EEWORLDEEWORLDEEWORLD

Part Number

Search

3150-1-224-11

Description
Board Connector, 24 Contact(s), 1 Row(s), Male, Straight, Solder Terminal
CategoryThe connector    The connector   
File Size80KB,1 Pages
ManufacturerMethode Electronics Inc.
Download Datasheet Parametric View All

3150-1-224-11 Overview

Board Connector, 24 Contact(s), 1 Row(s), Male, Straight, Solder Terminal

3150-1-224-11 Parametric

Parameter NameAttribute value
Reach Compliance Codeunknown
Connector typeBOARD CONNECTOR
Contact to complete cooperationTIN
Contact completed and terminatedTIN
Contact point genderMALE
DIN complianceNO
Filter functionNO
IEC complianceNO
JESD-609 codee3
MIL complianceNO
Manufacturer's serial number3100-1
Plug informationMULTIPLE MATING PARTS AVAILABLE
Mixed contactsNO
Installation methodSTRAIGHT
Installation typeBOARD
Number of rows loaded1
OptionsGENERAL PURPOSE
Terminal pitch3.96 mm
Termination typeSOLDER
Total number of contacts24
UL Flammability Code94V-0
Base Number Matches1
Has the Newman MP3 repair story strengthened our determination to DIY? (Reposted)
Seeing so many DIY MP3 stuff, I found this article online. I read it and saw if it strengthened our determination to DIY. I read an article saying that doctors refer their patients to other hospitals ...
小瑞 MCU
Learning is endless
I have just joined the ranks of learning microcontrollers. I hope I can learn a lot of useful knowledge here. I hope my work will go smoothly. Come on!...
swallow0608 Talking
How to troubleshoot and repair rectifier circuit failures?
[size=4] Rectifier diodes are mainly used in rectifier circuits, so the fault mechanism of rectifier circuits is related to rectifier diodes. A set of methods for detecting diodes can be used to troub...
fish001 Analogue and Mixed Signal
The main control chip of the inverter and its cracking
Most of TI's DSP chips are used in frequency converters. ①The main control chip of the inverter may have the following options: Based on MCU solution (Intel's N87C196MC, Renesas microcontroller, etc.)...
欣之 DSP and ARM Processors
A verilog program sent through the serial port, the running result is very strange
always @ (posedge txclk or posedge ld_tx_data or negedge reset) if(!reset) begin tx_reg0 && tx_cnt < 9) begin //transport bit1-bit8 tx_out <= tx_reg[tx_cnt -1]; end if (tx_cnt = = 9) begin //when cnt=...
nksosoon FPGA/CPLD
Dead in calibrating delay loop... How to solve it? Don't complain about the small points.
I wrote a framebuffer code for a certain chip and modified the corresponding Config.in fbmem.c Makefile under drives/video. I also made corresponding changes in make menuconfig. I use MIPS. When runni...
yuqinfeng Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2781  2052  901  2606  1199  56  42  19  53  25 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号