• Extremely low wavelength dependent loss (WDL) and PDL
• Up to 10-channel arrays
Applications
• EDFA
• Raman amplifiers
• Add/Drop monitoring
• DWDM systems
JDSU miniature integrated power monitors are designed for channel monitoring
in dense wavelength division multiplexing (DWDM) systems and Add/Drop
modules. They can also be used for signal/pump power monitoring in erbium
doped fiber amplifiers (EDFAs) and Raman amplifiers where integrated solutions
tend to replace traditional fused fiber tap + photodiodes. The miniaturized
version is a high performance active hybrid device that incorporates a micro-optic
tap coupler and high-sensitivity InGaAs photodiode in a miniature package. It
offers high reliability, compact footprint with ultra-wide bandwidth, and very low
polarization dependent loss (PDL).
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
MINIATURE INTEGRATED POWER MONITOR
2
IPM Single Unit Diagram
(Specifications in mm unless otherwise noted.)
20.1 MAX
18.35
7.0 MAX
Ø 3.20
0.50 X 0.50
Ø 0.50
PITCH 2.54
IPM Array (6 to 8 channels) Diagram
(Specifications in mm unless otherwise noted.)
32.00
3.20
PITCH 2.54 X 11
=27.94
3.0
Ø 0.51
Ø 1.14
PIN 1
27.94
32.50
22.86
6.00
IPM Array Pinout
(8 channel only)
BOTTOM VIEW
Pin
1
2
3
4
5
6
7
8
9
10
11
12
Description
Anode (Common)
Cathode 1
Cathode 2
Anode (Common)
Cathode 3
Cathode 4
Cathode 5
Anode (Common)
Cathode 6
Cathode 7
Anode (Common)
Cathode 8
MINIATURE INTEGRATED POWER MONITOR
3
Specifications
Parameter
Wavelength range
C-Band
L-Band
C+L Band
Insertion loss (input to output)
Wavelength flatness (input to output)
Polarization dependent loss (input to output)
PMD (input to output)
Optical return loss
PD operating bias voltage, V
R
PD responsivity
PD linearity
PD dark current
PD cut-off frequency
Input optical power
Operating temperature
Storage temperature
Tensile load
Package dimensions
Single unit
6 to 8 channels array
10 channels array
Fiber type
Pigtail color code
Specification
Maximum
Maximum
Maximum
Maximum
Minimum
Minimum
Maximum
Maximum
Maximum
1510-1580 nm
1560-1625 nm
1510-1625 nm
See table below
0.002 dB/nm
0.03 dB
0.1 ps
45 dB
-5 V (typical)
0.8 A/W (for net responsivity, see table below)
±10%
1 nA @ V
R
= -5 V and 23 °C
600 MHz @ V
R
= -5 V and R
L
= 50 W
See table below
-20 to 75 °C
-40 to 85 °C
5N
3.2 mm x 18.5 mm
32 mm x 32.5 mm x 6 mm
38.8 mm x 32.5 mm x 6 mm
SMF-28, 250 µm primary coating
Black (input port); Clear (output port)
Note: Parameters are specified for the signal wavelength range, all polarization states, and operating temperature range without connector unless otherwise stated.
Tap Ratio and Insertion Loss Table
Code
Tap Ratio
Maximum Insertion Loss
(Input to Output)
0.5 dB
0.5 dB
0.5 dB
0.5 dB
0.6 dB
0.8 dB
Minimum Net Responsivity
1
Maximum Optical Power
2
1
2
3
4
5
T
1%
2%
3%
4%
5%
10%
0.008 A/W
0.016 A/W
0.024 A/W
0.032 A/W
0.040 A/W
0.080 A/W
500 mW
250 mW
150 mW
125 mW
100 mW
50 mW
1. The net responsivity is defined as the ratio of the PD current output and optical power measured at output fiber.
2. The maximum optical power is the maximum value of the power at input port within the PD linearity range specified.
MINIATURE INTEGRATED POWER MONITOR
Ordering Information
For more information on this or other products and their availability, please contact your local JDSU account manager or
JDSU directly at 1-800-498-JDSU (5378) in North America and +800-5378-JDSU worldwide or via e-mail at
customer.service@jdsu.com.
Sample: IPM-C82310010
IPM-
Code
C
L
1
Wavelength
C-band
L-band
C + L bands
Code
1
2
3
4
5
T
Tap Ratio
1%
2%
3%
4%
5%
10%
Code
2
3
4
Package Size
Single
unit
6-8
channel
array
10-channel array
001
Code
0
1
2
3
4
5
8
9
A
B
C
Connector Type
No
connector
FC/PC
FC/SPC
FC/APC
SC/SPC
SC/APC
ST
FC/UPC
SC/UPC
LC/SPC
LC/UPC
Code
1
6
7
8
T
Channels
Single
device
6-channel array
7-channel array
8-channel array
10-channel array
Code
1
2
4
5
Fiber Length
1m
2m
0.5 m
1.5 m
SMF-28 is a registered trademark of Corning Incorporated.
ST is a registered trademark of Lucent Technologies.
All statements, technical information and recommendations related to the products herein are based upon information believed to be
reliable or accurate. However, the accuracy or completeness thereof is not guaranteed, and no responsibility is assumed for any
inaccuracies. The user assumes all risks and liability whatsoever in connection with the use of a product or its application. JDSU reserves
the right to change at any time without notice the design, specifications, function, fit or form of its products described herein, includ-
ing withdrawal at any time of a product offered for sale herein. JDSU makes no representations that the products
herein are free from any intellectual property claims of others. Please contact JDSU for more information. JDSU and the JDSU logo are
A real-time operating system (RTOS) is software that manages the time of a microprocessor or microcontroller. A real-time system is one in which serious consequences may occur if the logic and timing ...
One day, a new engineer asked me, what is the most important thing to do a good product development? This question stumped me. After thinking for a while, I answered: First: Never trust experience, no...
Generally speaking, the response result of the sensor has a strong linear correlation with the measured value, and some other physical quantities also affect the response value. For example, the respo...
As the title says, a curved magnet is mounted on a rotating shaft, and the output voltage is measured with a linear Hall sensor to obtain an approximately sinusoidal signal (not a 360-degree measureme...
1. Introduction to Carrier CommunicationPower line carrier communication (PLC) is a basic communication method unique to the power system. It refers to the technology of using existing power lines to ...
I have a basic knowledge of C++ but no work experience. I think this field has a good future and I want to learn it. Is it easy to learn by myself? What should I learn first? Please give me some advic...
The Mobile Industry Processor Interface (MIPI) Alliance is an organization responsible for promoting the standardization of software and hardware in mobile devices. It has released the D-PHY specif...[Details]
In public places such as schools, government agencies, factories and mines, as well as public corridors in residential areas, the phenomenon of long-burning lights is very common, which causes a h...[Details]
As cellular phones become more advanced, the power consumption of the system during operation and the power consumption during standby are also increasing. Therefore, the power management design of...[Details]
To differentiate their products in a crowded and competitive market, manufacturers of handheld devices often consider battery life and power management as key selling points for cell phones, PDAs, ...[Details]
July 11, 2012, Beijing - Altera Corporation (NASDAQ: ALTR) today announced the launch of 40-Gbps Ethernet (40GbE) and 100-Gbps Ethernet (100GbE) intellectual property (IP) core products. These core...[Details]
With the rapid development of urban economy, elevators are increasingly used as a vertical transportation tool. However, elevator fault detection and maintenance, especially the role of elevator remot...[Details]
1 Introduction
Ultrasonic waves have strong directivity, slow energy consumption, and can propagate over long distances in a medium, so they are used for distance measurement. Ultrasonic detec...[Details]
1. System Structure
This system is a simulation system of indoor air-conditioning temperature/humidity control system. The data acquisition and control center collects temperature/humidity...[Details]
LED is the abbreviation of light emitting diode, which is an electric light source made of semiconductor technology. The core part of LED is a chip composed of P-type semiconductor and N-type semi...[Details]
1 Introduction
There have been many studies on the detection and protection of power grid short circuit and line fault. The short circuit, overload and overvoltage protectors on the market have ...[Details]
In the single-chip microcomputer system, in addition to display devices, sound devices are often used, and the most common sound device is the buzzer. Buzzers are generally used for some low-demand...[Details]
Single-chip microcomputers are widely used because of their small size, powerful functions and low price. This article introduces the method of designing a micro electronic piano using the AT89C51 sin...[Details]
In today's body control module (BCM) designs, savvy engineers are moving away from electromechanical relays whenever possible. Their next step is to eliminate fuses. But is eliminating fuses a nece...[Details]
Robotics Development
京公网安备 11010802033920号
EEWORLD
