Over recommended operating conditions unless otherwise stated.
Symbol
R
POT
R
POT
R
POT
R
POT
Parameter
Potentiometer Resistance (-00)
Potentiometer Resistance (-50)
Potentiometer Resistance (-10)
Potentiometer Resistance (-2.5)
Potentiometer Resistance
Tolerance
R
POT
Matching
Power Rating
Wiper Current
Wiper Resistance
Wiper Resistance
Voltage on any R
H
or R
L
Pin
Resolution
Absolute Linearity
(5)
Relative Linearity
(6)
Temperature Coefficient of R
POT
Ratiometric Temp. Coefficient
Potentiometer Capacitances
Frequency Response
Test Conditions
Min
Typ
100
50
10
2.5
±20
25°C, each pot
I
W
= ±3mA @ V
CC
= 3V
I
W
= ±3mA @ V
CC
= 5V
V
SS
= 0V
R
W(n)(actual)
- R
(n)(expected)(8)
R
W(n+1)
- [R
W(n) + LSB
]
(8)
(4)
(4)
(4)
R
POT
= 50kΩ
(4)
±300
20
10/10/25
0.4
1
50
±6
300
150
V
CC
±1
±0.2
Max
Units
kΩ
kΩ
kΩ
kΩ
%
%
mW
mA
Ω
Ω
V
%
LSB
(7)
LSB
(7)
ppm/ºC
ppm/ºC
pF
MHz
Ratings
+2.5 to +6
-40 to +85
Units
V
°C
Ratings
-55 to +125
-65 to +150
-2.0 to +V
CC
+ 2.0
-2.0 to +7.0
1.0
300
±12
Units
ºC
°C
V
V
W
ºC
mA
I
W
R
W
R
W
V
TERM
80
GND
1.6
TC
RPOT
TC
RATIO
C
H
/C
L
/C
W
fc
Notes:
(1) Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions outside of those listed in the operational sections of this
specification is not implied. Exposure to any absolute maximum rating for extended periods may affect device performance and reliability.
(2) The minimum DC input voltage is –0.5V. During transitions, inputs may undershoot to –2.0V for periods of less than 20ns. Maximum DC
voltage on output pins is V
CC
+0.5V, which may overshoot to V
CC
+2.0V for periods of less than 20ns.
(3) Latch-up protection is provided for stresses up to 100mA on address and data pins from –1V to V
CC
+1V.
(4) This parameter is tested initially and after a design or process change that affects the parameter.
(5) Absolute linearity is utilized to determine actual wiper voltage versus expected voltage as determined by wiper position when used as a potentiometer.
(6) Relative linearity is utilized to determine the actual change in voltage between two successive tap positions when used as a potentio-
Many people think that portability is the ability of software to run normally when it is moved from one platform to another hardware platform. This statement is very general. If we think about it care...
I'm working on a pulse measurement project recently, but since I've only been using op amps for a short time, I'm aware of many problems during debugging. The attached file is my lm324 two-stage ampli...
I read the post [url]https://bbs.eeworld.com.cn/forum.php?mod=viewthread&tid=474609&highlight=access[/url] and I don't understand step 4, which is to add the file path (including the file name and suf...
Abstract: In order to generate a stable excitation signal, the design of a digital frequency synthesizer is implemented on FPGA using Verilog hardware language. The design includes accumulator, wav...[Details]
In public places such as schools, government agencies, factories and mines, as well as public corridors in residential areas, the phenomenon of long-burning lights is very common, which causes a h...[Details]
With the rapid development of urban economy, elevators are increasingly used as a vertical transportation tool. However, elevator fault detection and maintenance, especially the role of elevator remot...[Details]
AD8205 is
a single-supply high-performance differential
amplifier
launched by
Analog
Devices of the United States
. The typical single-supply voltage is 5V, and its common-mode volta...[Details]
Vertical cavity surface emitting lasers (VCSELs) are gradually replacing traditional edge emitting lasers, especially in low bandwidth and short-distance communication systems where cost factors ar...[Details]
LED is the abbreviation of light emitting diode, which is an electric light source made of semiconductor technology. The core part of LED is a chip composed of P-type semiconductor and N-type semi...[Details]
This controller uses PIC16C54 single-chip microcomputer as the controller, and it is very easy to use: just connect a telephone line to the loudspeaker through the controller, and you can rem...[Details]
It is well known to automotive suppliers that automakers are demanding more from their supply base. For connector suppliers, this means stricter requirements for product performance, stability and ...[Details]
The era of mobile access to the Internet has arrived, and it will rapidly change the business and infrastructure needs of mobile operators under a whole new trend of requirements. We need 4G LTE to...[Details]
Since the late 1990s, with the demand for higher system efficiency and lower power consumption, the technological update of telecommunications and data communication equipment has promoted the deve...[Details]
1. Overview
At present, an information revolution is in the ascendant around the world, led by microelectronics, computers and communication technologies, and centered on information technolog...[Details]
1 Introduction
With the improvement of people's quality of life, lamps are no longer just basic indoor lighting tools, but also a kind of practical art for architectural decoration. When ther...[Details]
Overview
By transmitting ultrasonic energy into the human body and receiving and processing the returning reflected signals, phased array ultrasound systems can generate images of organs and s...[Details]
Rated capacity refers to the maximum output power of the UPS (the product of voltage V and current A).
Usually, the UPS power supplies sold on the market are marked with "W" (watt) for smaller...[Details]
Don’t just look at the power when choosing a power supply
We know that a power supply with a low rated power can hardly meet the power supply needs of the system, which may cause frequent free...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
