Over recommended operating conditions unless otherwise stated.
Symbol
R
POT
R
POT
R
POT
R
POT
Parameter
Potentiometer Resistance (-00)
Potentiometer Resistance (-50)
Potentiometer Resistance (-10)
Potentiometer Resistance (-2.5)
Potentiometer Resistance
Tolerance
R
POT
Matching
Power Rating
Wiper Current
Wiper Resistance
Wiper Resistance
Voltage on any R
H
or R
L
Pin
Resolution
Absolute Linearity
(5)
Relative Linearity
(6)
Temperature Coefficient of R
POT
Ratiometric Temp. Coefficient
Potentiometer Capacitances
Frequency Response
Test Conditions
Min
Typ
100
50
10
2.5
±20
25°C, each pot
I
W
= ±3mA @ V
CC
= 3V
I
W
= ±3mA @ V
CC
= 5V
V
SS
= 0V
R
W(n)(actual)
- R
(n)(expected)(8)
R
W(n+1)
- [R
W(n) + LSB
]
(8)
(4)
(4)
(4)
R
POT
= 50kΩ
(4)
±300
20
10/10/25
0.4
1
50
±6
300
150
V
CC
±1
±0.2
Max
Units
kΩ
kΩ
kΩ
kΩ
%
%
mW
mA
Ω
Ω
V
%
LSB
(7)
LSB
(7)
ppm/ºC
ppm/ºC
pF
MHz
Ratings
+2.5 to +6
-40 to +85
Units
V
°C
Ratings
-55 to +125
-65 to +150
-2.0 to +V
CC
+ 2.0
-2.0 to +7.0
1.0
300
±12
Units
ºC
°C
V
V
W
ºC
mA
I
W
R
W
R
W
V
TERM
80
GND
1.6
TC
RPOT
TC
RATIO
C
H
/C
L
/C
W
fc
Notes:
(1) Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions outside of those listed in the operational sections of this
specification is not implied. Exposure to any absolute maximum rating for extended periods may affect device performance and reliability.
(2) The minimum DC input voltage is –0.5V. During transitions, inputs may undershoot to –2.0V for periods of less than 20ns. Maximum DC
voltage on output pins is V
CC
+0.5V, which may overshoot to V
CC
+2.0V for periods of less than 20ns.
(3) Latch-up protection is provided for stresses up to 100mA on address and data pins from –1V to V
CC
+1V.
(4) This parameter is tested initially and after a design or process change that affects the parameter.
(5) Absolute linearity is utilized to determine actual wiper voltage versus expected voltage as determined by wiper position when used as a potentiometer.
(6) Relative linearity is utilized to determine the actual change in voltage between two successive tap positions when used as a potentio-
Professor Chedan of the Transhuman Research Center at Harvard University found that people with messy desks are 50% more creative than those with neat desks; people who are often late have a 70% highe...
[i=s]This post was last edited by jameswangsynnex on 2015-3-3 19:59[/i] People often breed fish and shrimps, which often die in large numbers due to water pollution. Even the fish tanks at home need t...
I made a board for leakage testing, but the instrument does not leak electricity now. I want to try whether this board is easy to use. Is there any way to simulate leakage?...
I saw that other people's circuits driving IRF530 all use transistor push-pull output. Why is it designed this way? The input resistance of the field effect tube is not very large, and it can be contr...
1 System Overview
As shown in the figure, this is the principle block diagram of the entire video acquisition system. At the beginning of power-on, the FPGA needs to initialize the register configurat...
After learning that I had the honor to participate in the NXP Rapid IoT evaluation, I started to install the mobile APP. According to my previous experience, I chose to use my mobile phone to log in t...
1. Introduction
RFID (radio frequency identification) is a non-contact automatic identification technology that emerged in the 1990s. It uses the characteristics of radio frequency signal prop...[Details]
1 Introduction
The high temperature tester is mainly used for temperature tracking measurement and data acquisition during the heating process. By systematically analyzing the test data, the...[Details]
In recent years, lighting has become an important area that countries around the world are targeting to promote energy conservation and environmental protection. According to statistics, about 20% ...[Details]
Electronic systems are located at different points on the automotive power bus and therefore often need to operate under very stringent power requirements. These include load dump, cold crank, very lo...[Details]
1. What is temperature?
Heat is a type of molecular motion. The hotter an object is, the faster its molecules move. Absolute zero is defined as the temperature at which all molecular motion ...[Details]
1. Introduction
Testing the temperature of steel billets before rolling is an important measure to ensure the quality of steel. Traditional manual testing is difficult to ensure product qu...[Details]
introduction
MEMS is a high-tech that has flourished on the basis of integrated circuit production technology and dedicated micro-electromechanical processing methods. Pressure sensors develop...[Details]
Motors are important products that convert electrical energy into mechanical energy to achieve automation, and they are widely used in industrial control, medical electronics, white a...[Details]
Abstract: The output of high-range acceleration sensor is less than 10 mV under the excitation of small signal. The noise of traditional test system may cover such small voltage signal, so that hig...[Details]
Today, with energy becoming increasingly scarce, the utilization of natural energy has become the focus of people's attention. Among various natural energies, the endless solar energy is highly fav...[Details]
At present, a large number of cooling tower fans, speed fans and special fans are in use in petroleum, chemical, pharmaceutical, metallurgical and other enterprises. Some fans have no monitoring in...[Details]
This article discusses the six design steps of LED lighting system design in detail: (1) determine the lighting requirements; (2) determine the design goals and estimate the optics; (3) the efficie...[Details]
Multimedia processors are often the most power-hungry devices in portable electronic devices. Common ways to reduce CPU power requirements are to reduce clock frequency or operating voltage, but th...[Details]
introduction
The core features of mobile value-added service products are mobility, immediacy and personalization. Mobile value-added services are a new service mode that is rapidly developing...[Details]
1 Introduction
Automatic Test
System The ATS (Automatic Test System) integrates all the stimulus and measurement equipment required for testing.
The computer
efficiently comp...[Details]
Talking
京公网安备 11010802033920号
EEWORLD
