EEWORLDEEWORLDEEWORLD

Part Number

Search

87916-535H

Description
Board Connector, 35 Contact(s), 1 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size418KB,3 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Download Datasheet Parametric View All

87916-535H Overview

Board Connector, 35 Contact(s), 1 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Black Insulator, Receptacle

87916-535H Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresBREAKAWAY TYPE
body width0.095 inch
subject depth0.1 inch
body length3.5 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationNICKEL PALLADIUM GOLD (15) OVER NICKEL (50)
Contact completed and terminatedTIN LEAD (150) OVER NICKEL (50)
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Dielectric withstand voltage1500VAC V
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialGLASS FILLED POLYCYCLOHEXYLENE TEREPHTHALLATE
JESD-609 codee0
Manufacturer's serial number87916
Plug contact pitch0.1 inch
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
Maximum operating temperature130 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
Plating thicknessFLASH inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.128 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts35
Base Number Matches1
Help: Suggest to delete "EDA/IC Design" IC Design Rules, confidential documents, please post if you want!
It is recommended to delete the post "Confidential Document, Comments Required!" in "EDA/IC Design? IC Design Rules". This post is suspected of promoting other companies. There are so many comments be...
yfee Suggestions & Announcements
Under 6410, I used IROM_Fusing_Tool.exe to make an SD card boot disk and burned something into it, but why did the SD card capacity not change? Is it hidden?
Under 6410, I used IROM_Fusing_Tool.exe to make an SD card boot disk and burned something into it, but why did the SD card capacity not change? Is it hidden?...
htjsmhj Embedded System
DFM should not be limited to chips, PCB needs it more
We all know that even if the silicon is 100% perfect, if any one component of the chip-to-chip communication link (such as the package, connector or circuit board) is damaged, the target system may st...
clj2004000 PCB Design
Report Forum
I've been busy making an amplifier recently, so I don't have time to share my experience with M3 with you. The information is not very valuable (I think the most valuable ones have been posted), and I...
heavenji Microcontroller MCU
Introduction to Intel Embedded Systems Invitational Competition
[i=s]This post was last edited by paulhyde on 2014-9-15 09:01[/i] The "Intel Cup Undergraduate Electronic Design Competition - Embedded System Special Invitational Competition" is part of the National...
open82977352 Electronics Design Contest
Adjustment of basic idle speed of electronically controlled vehicles 3
(2006-04-04 13:20:26 ) e. Turn off the engine after adjusting the basic idle speed, and then clear the fault code (35#) stored in the computer after disconnecting the ISCV circuit. Methods for clearin...
frozenviolet Automotive Electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 871  91  2515  168  290  18  2  51  4  6 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号