EEWORLDEEWORLDEEWORLD

Part Number

Search

820NRA5E26

Description
CIT SWITCH
File Size192KB,3 Pages
ManufacturerCIT
Websitehttp://www.citswitch.com/
Download Datasheet View All

820NRA5E26 Overview

CIT SWITCH

820
SPECIFICATIONS
Electrical Ratings
Electrical Life
Contact Resistance
Actuation Force
Actuator Travel
Dielectric Strength
Insulation Resistance
Operating Temperature
Storage Temperature
100mA @ 48VDC
See Contact Options
100,000 cycles typical
< 50 mΩ initial
200 +/- 50gF
2.5 +/- .3mm
1000Vrms min
> 100MΩ min
-40°C to 85°C
-40°C to 85°C
MATERIALS
RoHS COMPLIANT
Actuator
Housing
Cover / Cap
Contacts
Terminals
Acetal
6/6 Nylon
6/6 Nylon
Silver or Gold plated copper alloy
Silver or Gold plated copper alloy
ORDERING INFORMATION
1. Series:
820
L
R
B
2
E2
820
2. Latching Option:
N = Momentary
L = Latching
3. Contact Options:
Q = Silver
R = Gold
4. Cap Style:
A = Large Cap
B = Small Cap
5. Cap Color:
1 = White
5 = Green
2 = Black
6 = Orange
3 = Red
7 = Blue
4 = Yellow
9 = Light Gray
6. Cover Style:
**ONLY AVAILABLE WITH “B SMALL CAP”
SS = Standard Cover
ES = Extended Cover
E1 = Extended Cover with 1 LED
E2 = Extended Cover with 2 LEDs
7. Cover Color:
1 = White
5 = Green
2 = Black
6 = Orange
3 = Red
7 = Blue
4 = Yellow
9 = Light Gray
8. LED 1 - Color:
Blank = No LED
R = Red
Y = Yellow
G = Green
9. LED 2 - Color:
Blank = No LED
R = Red
Y = Yellow
G = Green
2
R
G
Website: www.citswitch.com
Tel: 763-535-2339
Fax: 763-535-2194
[Xiao Meige FPGA Advanced Tutorial] Chapter 9 Serial Oscilloscope Download Based on Serial Port Hunter Software
[b]4. Basic Principles of DDS[/b] [color=#000][size=15px]Note: The content of this article is excerpted from the textbook "EDA Experiment and Practice" written by Zhou Ligong, pages 196-197. [/size][/...
芯航线跑堂 FPGA/CPLD
The minimum input voltage of a single-supply VI converter op amp is related to the load
[i=s]This post was last edited by 1nnocent on 2021-4-9 09:08[/i]The schematic diagram is as follows: If the input of a single-power op amp is not rail-to-rail, the op amp cannot input a signal close t...
1nnocent Analog electronics
Show the WEBENCH design process + multi-channel load power supply design solution
Designing a multi-load power supply using WEBENCH Design requirements: Design a 3-way power supply. Input range DC18V~DC26V, output 5V@2A, 3.3V@1A, [email]1.9V@0.5A[/email] three-way power supply. Amo...
ltbytyn Analogue and Mixed Signal
Analyze the internal circuit of an LED bulb
[backcolor=rgb(239, 245, 249)][size=14px]This is the internal circuit of an LED bulb I copied. I don't quite understand it. The output voltage of the bridge stack should be 310V. Why is such a small c...
House1989 Analog electronics
What are the pull-up and pull-down capabilities of a 0-10V dimmer?
What are the pull-up and pull-down capabilities of a 0-10V dimmer? I want to connect 100 dimmer power supplies in parallel. Will the dimmer's driving capacity be insufficient?...
ckf茉莉花 LED Zone
Some tips for protel
1: When laying out the board, first shrink the wiring area, hold down the right button, and see if the drawing board can be moved up, down, left, and right. If not, move it in the opposite direction u...
歹匕示申 FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 818  1249  2235  954  162  17  26  45  20  4 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号