The 5017-Series Delay System delivers unmatched performance for
radar testing, signal processing, phased antenna array, and phase
noise testing. The 5017 also provides unmatched convenience and
robustness because of its fully integrated fiber optics. All the fiber
interfaces are reliably fusion spliced internal to the box, thus eliminating
any handling and maintenance of optical connectors. The user only
needs to provide +5 and +15 volts, then plug in his RF connectors.
Emcore’s fiber-optic transceivers provide bandwidth that is essentially
independent of fiber length, loss or delay, and triple transit signals that
are immeasurable. In addition to enhanced electrical performance, the
delay lines provide several mechanical advantages. The small size of
these components allows for a long delay in a compact package with
the superior temperature stability of fiber. Emcore’s technology takes
advantage of the rigid yet flexible properties of fiber-optic cable to
provide repeatable enhanced phase and group delay characteristics.
Emcore’s Model 5017 consists of directly modulated DFB lasers and
photodiodes fabricated with mature, field-proven Ortel technology.
Performance Highlights
Min
Wavelength Options
1290
Typical
Max
1580
110
-25
0.1
-
-
+65
10 - 18
Units
nm
µ-sec
°C
GHz
Applications
Radar testing/calibration
Signal processing
Phased array antennas
Phase noise testing
Features
Bandwidth to 18 GHz
High dynamic range
Built-in optical isolator
1310 nm
Up to 110
µ
-sec
Integrated fiber
Internal Delay Spool
Temperature Range
Frequency Range
See following pages for complete specifications and conditions.
For more information on this and other products:
Contact Sales at Emcore 626-293-3400, or visit www.emcore.com.
5017-Series Delay Line
DATA SHEET
|
JANUARY 2, 2008
Absolute Maximum Ratings
Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are
absolute stress ratings only. Functional operation of the device is not implied at these or any other conditions in
excess of those given in the operational sections of the data sheet. Exposure to absolute maximum ratings for
extended periods can adversely affect device reliability.
Parameter
Operating Temperature Range of Baseplate:
Storage Temperature
RF Input Power
ESD, module
TEC Current, module
Symbol
T
OP
T
STG
P
IN
-
I
TEC
Condition
continuous
-
60 seconds
HBM: R = 1500 Ohm, C = 100 pF
continuous
Min
-55
-55
-
-500
-1.9
Max
+75
+85
20
500
1.9
Units
°C
°C
dBm
V
A
RF Characteristics
Parameter
Upper Band Edge Frequency
Lower Band Edge Frequency
Amplitude Flatness
Noise Figure
Max Delay Time
Insertion Loss
Input / Output Return Loss
Input Third Order Intercept
Impedance
Input 1 dB Compression
Triple Transit Response
9
+30
28
6
+25
50
+20
<-75
±
1.5
49
±
2.0
54
8
36
9
+30
50
6
+25
5017A
4
5017B
10
0.1
±
2.5
64
±
3.5
69
±
1.5
59
±
2.0
64
110
56
5017C
15
5017D
18
5017E
4
5017F
10
0.1
±
2.5
74
±
3.5
79
5017G
15
5017H
18
Unit
GHz
GHz
dB
dB
µ-sec
dB
dB
dBm
Ω
dBm
dBc
Connector Options
Parameter
Model Number
RF Connector
5017A/E
Specifications
5017B/F
5017C/G
5017D/H
SMA (f)
For more information on this and other products:
Contact Sales at Emcore 626-293-3400, or visit www.emcore.com.
5017-Series Delay Line
DATA SHEET
|
JANUARY 2, 2008
dc Interface Characteristics
Pin Number
1
2
Min
14V
4.75V
Typ
15V
5V
Max
16V
5.5V
Max Ripple
100 mV p-p
200 mV p-p
Current
0.3 A max
1.6 A max
Outline Diagram Model 5017A/B/C/B
Dimensions are in inches.
0.19
6.75
diameter 0.125
6.00
5.50
6.375
0.25
POWER ON
RF IN
DB 9 M
RF OUT
1.117
”
2.38
EMCORE
3 of 5
5017-Series Delay Line
DATA SHEET
|
JANUARY 2, 2008
Outline Diagram 5017E/F/G/H
Dimensions are in inches.
0.19”
6.75
diameter 0.125
6.00
5.50
6.375
0.25
X
Dimension “X”
35
µ-Sec
Max: 4.38 inches
60
µ-Sec
Max: 5.38 inches
80µ-Sec Max: 6.38 inches
110
µ-Sec
Max: 7.88 inches
POWER ON
2.38
RF IN
DB 9 M
RF OUT
1.117
”
For more information on this and other products:
Contact Sales at Emcore 626-293-3400, or visit www.emcore.com.
5017-Series Delay Line
DATA SHEET
|
JANUARY 2, 2008
Pin/Package Information
Nine-Pin D-sub Connector
Pin
1
2
3
4
5
6
7
8
9
Description
+15 Vdc
+5 Vdc
NC
Power Ground
Reference Ground
Laser Photodiode Current Monitor
Received Optical Power
Laser Current Monitor
Laser Over-temperature Alarm
1
Front Panel LEDs
Power on
dc Monitor Voltages
Laser Photodiode current, pin6
o
1V/100mA
±2%
accuracy (into 1 MΩ
load). Proportional to laser power at
beginning of fiber.
Photodiode current, pin7
o
1V/mA
±2%
accuracy (into 1 MΩ load).
Proportional to photodiode input power
end of fiber.
Laser dc current, pin 8:
o
1V/100mA
±2%
accuracy (into 1 MΩ
load).
Alarm Circuits
The alarms are open-collector outputs capable
20 mA when active and with standing +15
VDC when off.
Laser over temperature alarm, pin 9
o
Laser Temperature. This alarm is ON
(sinks current) if the laser substrate
temperature is more than 2
o
C higher
than the factory setpoint. The alarm is
not activated if the temperature is
LOWER than the setpoint.
Delay Time
The delay time is shown as “XXXX”.
X (hundreds) X (tens) X (ones) X (tenths)
A 5017C with a delay time of 15.5
µ-sec
would
be shown as 5017C-0155
1: Open collector outputs
Ordering Options Delay Line (For example, 5017A-0060)
5017
n-
Frequency
XXXX
Delay (Internal)
A
B
C
D
0.1 GHz to 4 GHz
0.1 GHz to 10 GHz
0.1 GHz to 15 GHz
0.1 GHz to 18 GHz
8
µ-sec
max
Ordering Options Delay Line (For example, 5017E-0850)
5017
n-
Frequency
XXXX
Delay (External)
E
F
G
H
0.1 GHz to 4 GHz
0.1 GHz to 10 GHz
0.1 GHz to 15 GHz
0.1 GHz to 18 GHz
110
µ-sec
max
Information contained herein is deemed to be reliable and accurate as of issue date. EMCORE reserves the right to change the design or specifications of
the product at any time without notice. Ortel, the Ortel logo, EMCORE, and the EMCORE logo are trademarks of EMCORE Corporation.
I used Corda's offline programmer to program the 430 chip. Under normal circumstances of the SBW two-wire system, there is no problem with programming whether online or offline. However, when the fuse...
Introduction Brushless DC motors and their drives are increasingly being used in home appliances, HVAC (HVAC ) and automotive applications . The reasons for this are their high efficiency, reliability...
I'm looking for an answer. I've just started learning ARM and I'm a complete novice and have no idea what to do. Why does this embedded assembler program report an error? void _nop_() { __asm("MOV R0,...
As medical equipment develops towards intelligence, miniaturization, serialization, digitization, and multi-functions, the logic control devices in medical equipment have also evolved from medium- a...[Details]
Preface
Sleep apnea is a very common sleep breathing disease. According to research, about 24% of adult men and 9% of adult women, or more than 2 million people, suffer from this disease ...[Details]
WiMax technology needs to demonstrate its advantages in specific application scenarios in order to gain market recognition, which requires application testing to measure system performance para...[Details]
In order to meet the requirements of video systems, industrial and medical display and video transmission applications such as eliminating the limitation of long connection cables, increasing data ...[Details]
Multi-parameter monitor is an important device in clinical nursing. It can monitor the patient's ECG, blood pressure, blood oxygen saturation, respiratory rate, pulse rate and temperature. At present,...[Details]
introduction
The data detected by various
measuring instruments
often need to be transferred to a PC for data processing and archiving, so as to make full use of the rich hardware an...[Details]
FSK (Frequeney-Shift Keying) uses carriers of different frequencies to transmit digital signals. FSK signals have the advantages of strong anti-interference ability and long transmission distance, and...[Details]
Focus shift problem
Visible light and infrared light have different wavelengths, so the imaging focus is not on the same plane, which results in a clear image under visible light condition...[Details]
0 Introduction
One of the basic tasks of machine vision is to obtain image information from the camera and calculate the geometric information of objects in three-dimensional space, so as ...[Details]
Today, many wireless devices combine GSM, WCDMA, Bluetooth, WLAN, GPS and FM technologies and support the high data rates required for mobile Internet. Moreover, as customers demand mobile wireless...[Details]
Fairchild Semiconductor provides the industry's smallest power management solution FAN5902 for 3G mobile phone and wireless data card designers. This RF power DC-DC converter uses a 12-bump 0.5mm p...[Details]
Designers have the most say, they believe that the most decisive integrated circuit technology in the 21st century is the field programmable gate array (FPGA), and traditional gate array and struct...[Details]
As modern cities develop towards multi-functionality, urban layouts become increasingly complex, with hundreds, even thousands of ground monitoring points. To ensure that functional departments can...[Details]
Today, a new systematic maintenance approach can measure, locate and repair problems in rail and tram tracks in a timely manner. Combining mature railway engineering techniques with advanced techno...[Details]
Body Control Module Design Requirements and ON Semiconductor Solutions
As people's demands for car controllability and comfort continue to increase, more and more electronic devices are in...[Details]
Analog electronics
京公网安备 11010802033920号
EEWORLD
