without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to
obtain the latest version of this device specification before relying on any published information and before placing orders for products.
Integrated Silicon Solution, Inc. — www.issi.com —
1-800-379-4774
Rev. A
9/26/02
1
IS45S16100
PIN FUNCTIONS
Pin No.
20 to 24
27 to 32
Symbol
A0-A10
Type
Input Pin
Function (In Detail)
ISSI
®
A0 to A10 are address inputs. A0-A10 are used as row address inputs during active
command input and A0-A7 as column address inputs during read or write command
input. A10 is also used to determine the precharge mode during other commands. If
A10 is LOW during precharge command, the bank selected by A11 is precharged,
but if A10 is HIGH, both banks will be precharged.
When A10 is HIGH in read or write command cycle, the precharge starts
automatically after the burst access.
These signals become part of the OP CODE during mode register set command
input.
A11 is the bank selection signal. When A11 is LOW, bank 0 is selected and when
high, bank 1 is selected. This signal becomes part of the OP CODE during mode
register set command input.
CAS,
in conjunction with the
RAS
and
WE,
forms the device command. See the
“Command Truth Table” item for details on device commands.
The CKE input determines whether the CLK input is enabled within the device. When
is CKE HIGH, the next rising edge of the CLK signal will be valid, and when LOW,
invalid. When CKE is LOW, the device will be in either the power-down mode, the
clock suspend mode, or the self refresh mode. The CKE is an asynchronous input.
CLK is the master clock input for this device. Except for CKE, all inputs to this device
are acquired in synchronization with the rising edge of this pin.
The
CS
input determines whether command input is enabled within the device.
Command input is enabled when
CS
is LOW, and disabled with
CS
is HIGH. The
device remains in the previous state when
CS
is HIGH.
I/O0 to I/O15 are I/O pins. I/O through these pins can be controlled in byte units
using the LDQM and UDQM pins.
LDQM and UDQM control the lower and upper bytes of the I/O buffers. In read
mode, LDQM and UDQM control the output buffer. When LDQM or UDQM is LOW,
the corresponding buffer byte is enabled, and when HIGH, disabled. The outputs go
to the HIGH impedance state when LDQM/UDQM is HIGH. This function
corresponds to
OE
in conventional DRAMs. In write mode, LDQM and UDQM control
the input buffer. When LDQM or UDQM is LOW, the corresponding buffer byte is
enabled, and data can be written to the device. When LDQM or UDQM is HIGH, input
data is masked and cannot be written to the device.
RAS,
in conjunction with
CAS
and
WE,
forms the device command. See the
“Command Truth Table” item for details on device commands.
WE,
in conjunction with
RAS
and
CAS,
forms the device command. See the
“Command Truth Table” item for details on device commands.
V
DDQ
is the output buffer power supply.
V
DD
is the device internal power supply.
GNDQ is the output buffer ground.
GND is the device internal ground.
19
A11
Input Pin
16
34
CAS
CKE
Input Pin
Input Pin
35
18
CLK
CS
Input Pin
Input Pin
2, 3, 5, 6, 8, 9, 11
12, 39, 40, 42, 43,
45, 46, 48, 49
14, 36
I/O0 to
I/O15
LDQM,
UDQM
I/O Pin
Input Pin
17
15
7, 13, 38, 44
1, 25
4, 10, 41, 47
26, 50
RAS
WE
V
DDQ
V
DD
GNDQ
GND
Input Pin
Input Pin
Power Supply Pin
Power Supply Pin
Power Supply Pin
Power Supply Pin
2
Integrated Silicon Solution, Inc. — www.issi.com —
1-800-379-4774
Rev. A
9/26/02
IS45S16100
FUNCTIONAL BLOCK DIAGRAM
ISSI
®
COMMAND
DECODER
&
CLOCK
GENERATOR
ROW DECODER
CLK
CKE
CS
RAS
CAS
WE
A11
MODE
REGISTER
11
11
ROW
ADDRESS
BUFFER
MEMORY CELL
ARRAY
2048
11
BANK 0
DQM
SENSE AMP I/O GATE
A10
8
COLUMN
ADDRESS BUFFER
BURST COUNTER
COLUMN
ADDRESS LATCH
DATA IN
BUFFER
16
16
256
COLUMN DECODER
ROW DECODER
MULTIPLEXER
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
REFRESH
CONTROLLER
SELF
REFRESH
CONTROLLER
I/O 0-15
8
256
SENSE AMP I/O GATE
REFRESH
COUNTER
DATA OUT
BUFFER
16
16
11
ROW
ADDRESS
LATCH
11
ROW
ADDRESS
BUFFER
2048
MEMORY CELL
ARRAY
V
DD
/V
DDQ
GND/GNDQ
BANK 1
11
S16BLK.eps
Integrated Silicon Solution, Inc. — www.issi.com —
1-800-379-4774
Rev. A
9/26/02
3
IS45S16100
ABSOLUTE MAXIMUM RATINGS
(1)
Symbol
V
DD
MAX
MAX
ISSI
Parameters
Maximum Supply Voltage
Maximum Supply Voltage for Output Buffer
Input Voltage
Output Voltage
Allowable Power Dissipation
Output Shorted Current
Operating Temperature
Storage Temperature
A
A1
Rating
–1.0 to +4.6
–1.0 to +4.6
–1.0 to +4.6
–1.0 to +4.6
1
50
0 to +70
-40 to +85
Unit
V
V
V
V
W
mA
°C
°C
®
V
DDQ
V
IN
V
OUT
P
D
I
CS
T
OPR
T
STG
MAX
–55 to +150 °C
DC RECOMMENDED OPERATING CONDITIONS
(2)
(
At T
A
= 0 to +70°C)
Symbol
V
DD
, V
DDQ
V
IH
V
IL
Parameter
Supply Voltage
Input High Voltage
(3)
Input Low Voltage
(4)
Min.
3.0
2.0
-0.3
Typ.
3.3
—
—
Max.
3.6
V
DD
+ 0.3
+0.8
Unit
V
V
V
CAPACITANCE CHARACTERISTICS
(1,2)
(At T
A
= +25°C, V
DD
= V
DDQ
= 3.3 ± 0.3V, f = 1 MHz)
Symbol
C
IN
1
C
IN
2
CI/O
Parameter
Input Capacitance: A0-A11
Input Capacitance: (CLK, CKE,
CS, RAS, CAS, WE,
LDQM, UDQM)
Data Input/Output Capacitance: I/O0-I/O15
Typ.
—
—
—
Max.
4
4
5
Unit
pF
pF
pF
Notes:
1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a
stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
reliability.
2. All voltages are referenced to GND.
3. V
IH
(max) = V
DDQ
+ 2.0V with a pulse width
≤
3 ns.
4
Integrated Silicon Solution, Inc. — www.issi.com —
When using USB to transfer data under wince, calling GetTransferStatus shows the error value USB_DATA_OVERRUN_ERROR. What caused this error? Thank you...
Today I was looking at the Linux kernel semaphore, and there was a question I didn't understand. Please help! The code of the up() function that releases the semaphore in the book is: movl $sem->count...
[size=4] Because the G2 series has fewer IO ports, the LCD display has always been serial. In the end, only 3 ports were connected. PSB was directly connected to ground. RST was not connected, but it ...
[align=left][color=rgb(51, 51, 51)][font="]Today, the editor has summarized the basic common sense of module power supply. Please listen carefully! [/font][/color][/align][align=left][color=rgb(51, 51...
Chip: stm32f030f4 Problem: uart1 and tim1_ch1n pwm output cannot coexist. Outputting either one of them is normal. Please give me some advice.[/size][/backcolor][/color] [color=#000][backcolor=rgb(232...
From: Tencent I just read the news about the Chengdu bus fire, and I feel very sad. Dozens of lives were lost in a flash. From smoke and fire to a disaster, it only took five minutes. [align=center][/...
The TIA Portal software's shift instructions shift the contents of an accumulator bit by bit to the left or right. The number of bits shifted is determined by N. A left shift of N bits multiplies t...[Details]
There are many different ways of human-computer interaction. The more common ones are listed below:
Mouse interaction: Using a mouse to operate a computer and interact was the most common human...[Details]
Tesla and BYD, vying for dominance in the global electric vehicle market, are reportedly considering adopting Samsung's AMOLED (active-matrix organic light-emitting diode) technology for their next...[Details]
introduction
Bluetooth technology is a short-range wireless communication technology designed to replace wired cables. It is a wireless communication technology standard developed by the SIG, ...[Details]
introduction
With the development of digital and network technologies, broadcasting technology has become increasingly diversified, with the most significant trend being the transition from an...[Details]
On August 25th, Apple's expansion in India encountered new troubles. According to Bloomberg, Foxconn Technology Group has recalled approximately 300 Chinese engineers from India, further hindering ...[Details]
As the scale and business applications of national e-government networks continue to expand, the data and services transmitted over them are becoming increasingly sensitive and critical. To protect...[Details]
Normally, we determine our location and where we want to go by comparing our surroundings with observation and simple GPS tools. However, this kind of reasoning is very difficult for self-driving c...[Details]
A human-machine interface (HMI) refers to the platform used by people to operate a PLC. This platform provides an interface between programs and humans, serving as a medium for information transmis...[Details]
Over the past decade, the narrative surrounding fuel vehicles has been one of decline and replacement. Under the onslaught of new energy vehicles, traditional automakers have been forced to acceler...[Details]
There are many motors that can use thyristor speed control, and they can be used in almost all industries. Various types of motors, such as fans, pumps, AC motors, DC motors, torque motors, single-...[Details]
Batteries, at the core of new energy vehicles, are crucial to vehicle performance and range. Existing automotive batteries are categorized into lead-acid and lithium batteries. Currently, new energ...[Details]
With the support and encouragement of national policies, some Internet car manufacturers have also joined the new energy vehicle manufacturing industry. From the perspective of new car manufacturer...[Details]
For self-driving cars, LiDAR is the sensory organ that allows them to "see the road." Simply put, its operating principle involves sending out a laser beam, receiving the echo, and ultimately gener...[Details]
introduction
The rapid development of science and technology has enabled mankind to quickly move from the Internet era to the big data era. As a result, the amount of data generated by people ...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
