The LOGDAC® AD7112 is a monolithic dual multiplying D/A
converter featuring wide dynamic range and excellent DAC-to-
DAC matching. Both DACs can attenuate an analog input sig-
nal over the range 0 dB to 88.5 dB in 0.375 dB steps. It is
available in skinny 0.3" wide 20-pin DIPs and in 20-terminal
surface mount packages.
The degree of attenuation in either channel is determined by the
8-bit word applied to the onboard decode logic. This 8-bit word
is decoded into a 17-bit word which is then loaded into one of
the 17-bit data latches, determined by
DACA/DACB.
The fine
step resolution over the entire dynamic range is due to the use of
these 17-bit DACs.
The AD7112 is easily interfaced to a standard 8-bit MPU bus
via an 8-bit data port and standard microprocessor control lines.
It should be noted that the AD7112 is exactly pin-compatible
with the AD7528, an industry standard dual 8-bit multiplying
DAC. This allows an easy upgrading of existing AD7528 de-
signs which would benefit both from the wider dynamic range
and the finer step resolution offered by the AD7112.
The AD7112 is fabricated in Linear Compatible CMOS
(LC
2
MOS), an advanced, mixed technology process that com-
bines precision bipolar circuits with low power CMOS logic.
*Protected
by U.S. Patent No. 4521764.
LOGDAC is a registered trademark of Analog Devices, Inc.
PRODUCT HIGHLIGHTS
1. DAC-to-DAC Matching: Since both of the AD7112 DACs
are fabricated at the same time on the same chip, precise
matching and tracking between the two DACs is inherent.
2. Small Package: The AD7112 is available in a 20-pin DIP
and a 20-terminal SOIC package.
3. Fast Microprocessor Interface: The AD7112 has bus inter-
face timing compatible with all modern microprocessors.
REV. 0
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 617/329-4700
Fax: 617/326-8703
AD7112–SPECIFICATIONS
(V = +5toVT
Output amplifier AD712 except where noted. All specifications T
DD
MIN
5%; OUT A = OUT B = AGND = DGND = 0 V; V
IN
A = V
IN
B = 10 V.
MAX
unless otherwise noted.)
Parameter
ACCURACY
Resolution
Accuracy Relative to
0 dB Attenuation
0.375 dB Steps:
Accuracy
≤ ±
0.17 dB
Monotonic
0.75 dB Steps:
Accuracy
≤ ±
0.35 dB
Monotonic
1.5 dB Steps:
Accuracy
≤ ±
0.7 dB
Monotonic
3.0 dB Steps:
Accuracy
≤ ±
1.4 dB
Monotonic
6.0 dB Steps:
Accuracy
≤ ±
2.7 dB
Monotonic
Gain Error
C Version
T
A
=
T
A
=
+25 C
T
MIN
, T
MAX
0.375
0.375
1
B Version
T
A
=
T
A
=
+25 C
T
MIN
, T
MAX
0.375
0.375
Units
dB
Conditions/Comments
Guaranteed Attenuation
Ranges for Specified Step Sizes.
0 to 36
0 to 54
0 to 48
0 to 72
0 to 36
0 to 54
0 to 42
0 to 66
0 to 30
0 to 48
0 to 42
0 to 72
0 to 48
0 to 85.5
0 to 30
0 to 48
0 to 36
0 to 60
0 to 42
0 to 72
dB min
dB min
dB min
dB min
dB min
dB min
dB min
dB min
dB min
dB min
dB max
0 to 54
0 to 48
Full Range 0 to 78
0 to 66
0 to 54
Full Range Full Range
0 to 72
0 to 60
Full Range Full Range
±
0.1
±
0.15
Full Range Is 0 dB to 88.5 dB.
0 to 60
0 to 48
Full Range Full Range
0 to 60
0 to 60
Full Range Full Range
±
0.15
±
0.2
Measured Using R
FB
A,
R
FB
B. Both DAC Registers
Loaded With All 0s.
Output Leakage Current
OUT A, OUT B
Input Resistance,
V
IN
A, V
IN
B
Input Resistance Match
Feedback Resistance,
R
FB
A, R
FB
B
LOGIC INPUTS
CS, WR,
DAC A/DAC
B,
DB0–DB7
Input Low Voltage, V
INL
Input High Voltage, V
INH
Input Leakage Current
Input Capacitance
2
POWER REQUIREMENTS
V
DD
, Range
3
±
50
9/15
±
1
9.3/15.7
±
400
9/15
±
1
9.3/15.7
±
50
9/15
±
2
9.3/15.7
±
400
9/15
±
2
9.3/15.7
nA max
kΩ min/max Typically 12 kΩ.
% max
kΩ min/max
0.8
2.4
±
1
10
4.75/5.25
2
2
0.8
2.4
±
10
10
4.75/5.25
2
2
0.8
2.4
±
1
10
4.75/5.25
2
2
0.8
2.4
±
10
10
4.75/5.25
2
2
V max
V min
µA
max
pF max
V min/max
mA max
mA max
For Specified Performance.
Logic Inputs = V
IL
or V
IH
Logic Inputs = 0 V or V
DD
NOTES
l
Temperature range as follows: B, C Versions: –40°C to +85°C.
2
Guaranteed by design, not production tested.
3
The part will function with V
DD
= 5 V
±
10% with degraded performance.
Specifications subject to change without notice.
–2–
REV. 0
AD7112
TIMING SPECIFICATIONS
1
(V
Parameter
CS
to
WR
Setup Time
CS
to
WR
Hold Time
DAC Select to
WR
Setup Time
DAC Select to
WR
Hold Time
Data Valid to
WR
Setup Time
Data Valid to
WR
Hold Time
WR
Pulse Width
t
CS
t
CH
t
AS
t
AH
t
DS
t
DH
t
WR
DD
= +5 V
5%; 0UT A = OUT B = AGND = DGND = O V; V
IN
A = V
IN
B = 10 V)
T
A
= –40 C to +85 C
0
0
4
0
55
10
53
Units
ns min
ns min
ns min
ns min
ns min
ns min
ns min
Conditions/Comments
See Figure 3.
T
A
= +25 C
0
0
4
0
55
10
53
NOTES
1
Timing specifications guaranteed by design not production tested. All input signals are specified with tr = tf = 5 ns (10% to 90% of 5 V) and timed from a voltage
level of 1.6 V.
Specifications subject to change without notice.
AC PERFORMANCE CHARACTERISTICS
Parameter
DC Supply Rejection
∆
Gain/∆ V
DD
Digital-to-Analog Glitch Impulse
Output Capacitance, C
OUT A
, C
OUT B
AC Feedthrough
V
IN
A to OUT A
V
IN
B to OUT B
Channel-to-Channel Isolation
V
IN
A to OUT B
V
IN
B to OUT A
Digital Feedthrough
Output Noise Voltage Density
(30 Hz to 50 kHz)
Total Harmonic Distortion
NOTES
1
Guaranteed by design, not production tested.
Specifications subject to change without notice.
1
(V
DD
= +5 V
5%; 0UT A = OUT B = AGND = DGND = 0 V; V
IN
A =
V
IN
B = 10 V. Output amplifier AD712 except where noted.)
T
A
=
+25 C
0.001
10
50
–94
–94
–87
–87
1
15
–91
T
A
=
–40 C to
+85 C
0.005
10
50
–90
–90
–87
–87
1
15
–91
Units
dB/% max
nV s typ
pF max
dB max
dB max
dB typ
dB typ
nV s typ
nV/√Hz typ
dB typ
Conditions/Comments
∆
V
DD
=
±
5%. Input Code = 00000000
Measured with AD843 as output amplifier for input
code transition 10000000 to 00000000.
V
IN
A, V
IN
B = 6 V rms at 1 kHz. DAC
Registers loaded with all 1s.
V
IN
A = 6 V rms at 10 kHz sine wave,
V
IN
B = 0 V. DAC Registers loaded with all 0s.
V
IN
B = 6 V rms at 10 kHz sine wave,
V
IN
A = 0 V. DAC Registers loaded with all 0s.
Measured with input code transitions of all 0s to all 1s.
Measured between R
FB
A and OUT A or between
R
FB
B and OUT B.
V
IN
A = V
IN
B = 6 V rms at 1 kHz. DAC
Registers loaded with all 0s.
REV. 0
–3–
AD7112
ABSOLUTE MAXIMUM RATINGS*
V
DD
to AGND or DGND . . . . . . . . . . . . . . . . . . –0.3 V, +7 V
[i=s]This post was last edited by paulhyde on 2014-9-15 03:04[/i] I would like to ask everyone, what kind of device do you choose for the mechanical part of the metal detector, is it a gear sliding li...
It has been a while since I got the UFUN board. As I have been busy with work recently, I have not found time to take a look at this board. Overall, the UFUN development board is relatively small, eas...
I received the Renesas R7F0C809 development kit by express delivery. I won't post pictures since there is already an unpacking post. I will share some of my experience. 1. List of development boards T...
Please indicate the source and author contact information when reprintingArticle source: http://www.limodev.cn/blogAuthor contact: Li Xianjing xianjimli@gmail.com FTK supports themes. Using theme conf...
Recently I found on the Jiali Chuang forum that Jiali Chuang only posts green boards, so I was wondering if the color of the board has an effect on the patch, or if Jiali Chuang only posts green for c...
Click to enter the live broadcast
Live broadcast time:
October 22, 2020, 10:00-11:30 amLive broadcast topic:
Gigabit Digital Isolators for Video, Converters, CommunicationsLive Introduction:Various re...
introduction
my country has a vast territory and a large population. The scale of housing construction is huge, and the amount of residential construction is large and wide. It is still on t...[Details]
Google's driverless technology is not only an eye-catching technology, but also a subversion of the car usage model.
Those who have watched anti-terrorism films and TV dramas must have been im...[Details]
introduction
In the discharge process of tokamak plasma physics, the study of rupture and sawtooth is of great significance. Rupture and sawtooth exist in most tokamaks. Rupture is a notew...[Details]
Aromatic gases are widely present in food, medicine, cosmetics and various daily chemical products, such as snacks, liquor, spices, Chinese herbal medicines, plasters, perfumes, soaps, shampoos, et...[Details]
Overview
As a remote network communication control method with advanced technology, high reliability, complete functions and reasonable cost, CAN-bus has been widely used in various automa...[Details]
Capacitors
are basic components in various electronic devices and are widely used for bypassing, coupling,
filtering
, tuning, etc. in electronic circuits. However, to use capacitors,...[Details]
Abstract: Aiming at the needs of coal-rock acoustic emission signal monitoring system, a data acquisition circuit with 24-bit resolution and 16-channel synchronous data acquisition function is desi...[Details]
hint:
The number of speakers and their spacing limit the sound field of a portable stereo system.
Spatial audio attempts to artificially recreate the experience of listening to sounds i...[Details]
1 Basic Features
In computer control systems and various intelligent instruments and meters composed of single-chip microcomputers (or microprocessors), various external analog signals must be ...[Details]
Temperature compensated quartz crystal oscillator (TCXO) is widely used as a high-precision frequency source in communication systems, radar navigation systems, precision measurement and control sy...[Details]
Distributed Wireless Communication System (DWCS) uses distributed antennas, distributed processing control, joint signal processing and other technologies to improve the system's spectrum efficie...[Details]
For battery-powered portable devices, in addition to breaking through the limitations of processing power, the performance of portable system power supplies also needs to be continuously improved. ...[Details]
Measurement compatibility
It is very important to ensure the compatibility between the pressure sensor and its actual application. Before making a pressure sensor selection, the fo...[Details]
1 Introduction
At present, advocating health has become the focus of people's attention, and the emergence of treadmills has become more and more popular. People can exercise at home or in the ...[Details]
introduction
Temperature and humidity are the main environmental parameters of industrial and agricultural production. It is of great significance to measure them accurately and timely. Using a s...[Details]
Electronics Design Contest
京公网安备 11010802033920号
EEWORLD
