2.5V / 3.3V QUAD ACTIVE LOW, HIGH BANDWIDTH SWITCH
INDUSTRIAL TEMPERATURE RANGE
QUICKSWITCH
®
PRODUCTS
2.5V / 3.3V QUAD ACTIVE LOW,
HIGH BANDWIDTH BUS SWITCH
FEATURES:
DESCRIPTION:
IDTQS3VH125
• N channel FET switches with no parasitic diode to V
CC
– Isolation under power-off conditions
– No DC path to V
CC
or GND
– 5V tolerant in OFF and ON state
• 5V tolerant I/Os
• Low R
ON
- 4Ω typical
Ω
• Flat R
ON
characteristics over operating range
• Rail-to-rail switching 0 - 5V
• Bidirectional dataflow with near-zero delay: no added ground
bounce
• Excellent R
ON
matching between channels
• V
CC
operation: 2.3V to 3.6V
• High bandwidth - up to 500MHz
• LVTTL-compatible control Inputs
• Undershoot Clamp Diodes on all switch and control Inputs
• Low I/O capacitance, 4pF typical
• Available in QSOP and SOIC packages
The QS3VH125 is a high bandwidth, Quad bus switch. The QS3VH125
has very low ON resistance, resulting in under 250ps propagation delay
through the switch. The switches can be turned ON under the control
of individual LVTTL-compatible active low Output Enable signals for
bidirectional data flow with no added delay or ground bounce. In the ON
state, the switches can pass signals up to 5V. In the OFF state, the
switches offer very high impedence at the terminals.
The combination of near-zero propagation delay, high OFF imped-
ance, and over-voltage tolerance makes the QS3VH125 ideal for high
performance communications applications.
The QS3VH125 is characterized for operation from -40°C to +85°C.
APPLICATIONS:
•
•
•
•
•
Hot-swapping
10/100 Base-T, Ethernet LAN switch
Low distortion analog switch
Replaces mechanical relay
ATM 25/155 switching
FUNCTIONAL BLOCK DIAGRAM
1
A
2
A
3
A
4
A
1OE
2OE
3OE
4OE
1
Y
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
2
Y
3
Y
4
Y
INDUSTRIAL TEMPERATURE RANGE
1
c
2013 Integrated Device Technology, Inc.
JANUARY 2013
DSC-5597/11
IDTQS3VH125
2.5V / 3.3V QUAD ACTIVE LOW, HIGH BANDWIDTH SWITCH
INDUSTRIAL TEMPERATURE RANGE
PIN CONFIGURATION
ABSOLUTE MAXIMUM RATINGS
(1)
Symbol
Description
Max
V
TERM
(2)
SupplyVoltage to Ground
V
TERM
(3)
DC Switch Voltage V
S
–0.5 to +4.6
–0.5 to +5.5
–0.5 to +5.5
–3
120
–65 to +150
Unit
V
V
V
V
mA
°C
NC
1OE
1
A
1
Y
2OE
2
A
2
Y
GND
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
V
CC
4OE
4
A
4
Y
3OE
3
A
3
Y
NC
V
TERM
(3)
DC Input Voltage V
IN
V
AC
I
OUT
T
STG
AC Input Voltage (pulse width
≤20ns)
DC Output Current (max. sink current/pin)
Storage Temperature
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and functional operation of
the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
2. V
CC
terminals.
3. All terminals except V
CC
.
QSOP
TOP VIEW
0V)
Symbol
C
IN
C
I/O
C
I/O
CAPACITANCE
Parameter
(1)
Control Inputs
(T
A
= +25°C, F = 1MHz, V
IN
= 0V, V
OUT
=
Typ.
3
4
8
Max.
5
6
12
Unit
pF
pF
pF
Quickswitch Channels (Switch OFF)
Quickswitch Channels (Switch ON)
NOTE:
1. This parameter is guaranteed but not production tested.
1OE
1
A
1
Y
2OE
2
A
2
Y
GND
1
2
3
4
5
6
7
14
13
12
11
10
9
8
V
CC
4OE
4
A
4
Y
3OE
3
A
3
Y
PIN DESCRIPTION
Pin Names
1
A
- 4
A
1
Y
- 4
Y
1OE
-
4OE
I/O
I/O
I/O
I
Bus A
Bus Y
Output Enable
Description
FUNCTION TABLE
(1)
SOIC
TOP VIEW
OE
L
L
H
A
H
L
X
Y
H
L
X
Function
Connect
Connect
Disconnect
NOTE:
1. H = HIGH Voltage Level
L = LOW Voltage Level
X = Don't Care
2
IDTQS3VH125
2.5V / 3.3V QUAD ACTIVE LOW, HIGH BANDWIDTH SWITCH
INDUSTRIAL TEMPERATURE RANGE
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified:
Industrial: T
A
= –40°C to +85°C, V
CC
= 3.3V ±0.3V
Symbol
V
IH
V
IL
I
IN
I
OZ
I
OFF
R
ON
Parameter
Input HIGH Voltage
Input LOW Voltage
Input Leakage Current (Control Inputs)
Off-State Current (Hi-Z)
Data Input/Output Power Off Leakage
Switch ON Resistance
for Control Inputs
Guaranteed Logic LOW
for Control Inputs
0V
≤
V
IN
≤
V
CC
0V
≤
V
OUT
≤
5V, Switches OFF
V
IN
or V
OUT
0V to 5V, V
CC
= 0V
V
CC
= 2.3V
Typical at V
CC
= 2.5V
V
CC
= 3V
NOTE:
1. Typical values are at V
CC
= 3.3V and T
A
= 25°C.
Test Conditions
Guaranteed Logic HIGH
V
CC
= 2.3V to 2.7V
V
CC
= 2.7V to 3.6V
V
CC
= 2.3V to 2.7V
V
CC
= 2.7V to 3.6V
Min.
1.7
2
—
—
—
—
—
Typ.
(1)
Max.
—
—
—
—
—
—
—
6
7
4
5
—
—
0.7
0.8
±1
±1
±1
8
9
6
8
Unit
V
V
μA
μA
μA
Ω
V
IN
= 0V
V
IN
= 1.7V
V
IN
= 0V
V
IN
= 2.4V
I
ON
= 30mA
I
ON
= 15mA
I
ON
= 30mA
I
ON
= 15mA
—
—
—
—
TYPICAL ON RESISTANCE vs V
IN
AT V
CC
= 3.3V
16
14
R
ON
(ohms)
12
10
8
6
4
2
0
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
V
IN
(Volts)
3
IDTQS3VH125
2.5V / 3.3V QUAD ACTIVE LOW, HIGH BANDWIDTH SWITCH
INDUSTRIAL TEMPERATURE RANGE
POWER SUPPLY CHARACTERISTICS
Symbol
I
CCQ
ΔI
CC
I
CCD
Parameter
Quiescent Power Supply Current
Power Supply Current
(2,3)
per Input HIGH
Dynamic Power Supply Current
(4)
Test Conditions
(1)
V
CC
= Max., V
IN
= GND or V
CC
, f = 0
V
CC
= Max., V
IN
= 3V, f = 0 per Control Input
V
CC
= 3.3V, A and Y Pins Open, Control Inputs
Toggling @ 50% Duty Cycle
Min.
—
—
Typ.
2
—
Max.
4
30
Unit
mA
μA
See Typical I
CCD
vs Enable Frequency graph below
NOTES:
1. For conditions shown as Min. or Max., use the appropriate values specified under DC Electrical Characteristics.
2. Per input driven at the specified level. A and Y pins do not contribute to
ΔIcc.
3. This parameter is guaranteed but not tested.
4. This parameter represents the current required to switch internal capacitance at the specified frequency. The A and Y inputs do not contribute to the Dynamic Power Supply Current. This
parameter is guaranteed but not production tested.
TYPICAL I
CCD
vs ENABLE FREQUENCY CURVE AT V
CC
= 3.3V
6
4
I
CCD
(mA)
2
0
0
2
4
6
8
10
12
14
16
18
20
ENABLE FREQUENCY (MHz)
4
IDTQS3VH125
2.5V / 3.3V QUAD ACTIVE LOW, HIGH BANDWIDTH SWITCH
INDUSTRIAL TEMPERATURE RANGE
SWITCHING CHARACTERISTICS OVER OPERATING RANGE
T
A
= -40°C to +85°C
V
CC
= 2.5 ± 0.2V
(1)
Symbol
t
PLH
t
PHL
t
PZL
t
PZH
t
PLZ
t
PHZ
f
xOE
Parameter
Data Propagation Delay
(2,3)
A to Y
Switch Turn-On Delay
xOE
to xA/xY
Switch Turn-Off Delay
xOE
to xA/xY
Operating Frequency -Enable
(2,5)
Min
.
(4)
V
CC
= 3.3 ± 0.3V
(1)
Min
.
(4)
⎯
1.5
1.5
Max.
0.2
6.5
7
20
Unit
ns
ns
ns
MHz
Max.
0.2
8
7
10
⎯
1.5
1.5
⎯
⎯
NOTES:
1. See Test Conditions under TEST CIRCUITS AND WAVEFORMS.
2. This parameter is guaranteed but not production tested.
3. The bus switch contributes no propagation delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone is of the
order of 0.2ns at C
L
= 50pF. Since this time constant is much smaller than the rise and fall times of typical driving signals, it adds very little propagation delay to the system. Propagation
delay of the bus switch, when used in a system, is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side.
4. Minimums are guaranteed but not production tested.
My graduation project needs to collect DHT11 and light intensity data through ZIGBEE, but I don't know how to write the collection program of my bloodthirsty router. The protocol stack has been tested...
After the coordinator is networked, the terminal cannot be added to the network. After simulation, it is found that the following if statement is not true! ! ! ! ! if ( events & ZDO_NETWORK_INIT ) // ...
/******************************************************************** Serial port sends string function ************************************************************/ void UartTX_Send(unsigned char *Da...
Can anyone tell me what a communication protocol is? What is a communication protocol? I know the function and definition of a communication protocol. But what is its carrier? Is it a string of code? ...
When designing PCB, do you save the library file and PCB drawings in one folder? This makes it easier to share drawings. If others don't have this library, won't the 3D display be incomplete when they...
Emergency hand-held lamps powered by 6V maintenance-free batteries are widely used in rural areas. The charger used is a transformer step-down and single diode half-wave rectifier, and the charging...[Details]
This program is written to simulate the serial port hardware mechanism. When used, a timed interrupt can be set with a time interval of 1/4 baud rate. The receiving function is called once for ea...[Details]
As a wireless broadband metropolitan area network standard, WiMAX technology has greater advantages than previous 3.5GHz MMDS products in terms of non-line-of-sight transmission and spectrum utiliz...[Details]
introduction
In the discharge process of tokamak plasma physics, the study of rupture and sawtooth is of great significance. Rupture and sawtooth exist in most tokamaks. Rupture is a notew...[Details]
DSP (digital signal processor) is used more and more frequently in today's engineering applications. There are three main reasons for this: first, it has powerful computing power and is capable of ...[Details]
0 Introduction
With the development of society, people pay more and more attention to security work. Monitoring products have been used in various fields instead of being used only in importan...[Details]
1. Introduction to CIF Board
Fieldbus integration based on PC system
Whether it is a master or a slave, fieldbus has won unanimous praise in the field of PC-based automation. For more...[Details]
LED lamps and bulbs are now rapidly replacing incandescent, halogen and CFL (compact fluorescent lamp) light sources in many general lighting applications. Flyback DC/DC converters are the power su...[Details]
1 Introduction
There have been many studies on the detection and protection of power grid short circuit and line fault. The short circuit, overload and overvoltage protectors on the market have ...[Details]
Among the many members of the single-chip microcomputer family, the MCS-51 series of single-chip microcomputers has occupied the main market of industrial measurement and control and automation eng...[Details]
From the previous section, we have learned that the timer/counter in the microcontroller can have multiple uses, so how can I make them work for the purpose I need? This requires setting the timer/...[Details]
Single-chip microcomputers are widely used because of their small size, powerful functions and low price. This article introduces the method of designing a micro electronic piano using the AT89C51 sin...[Details]
hint:
The number of speakers and their spacing limit the sound field of a portable stereo system.
Spatial audio attempts to artificially recreate the experience of listening to sounds i...[Details]
1 Basic Features
In computer control systems and various intelligent instruments and meters composed of single-chip microcomputers (or microprocessors), various external analog signals must be ...[Details]
At present, how various communication technologies will evolve after 3G is a focus of great concern in the industry. Especially for TD-SCDMA, whether it can achieve smooth evolution to the next gen...[Details]
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
