Over recommended operating conditions unless otherwise stated.
Symbol
R
POT
R
POT
R
POT
R
POT
Parameter
Potentiometer Resistance (-00)
Potentiometer Resistance (-50)
Potentiometer Resistance (-10)
Potentiometer Resistance (-2.5)
Potentiometer Resistance
Tolerance
R
POT
Matching
Power Rating
Wiper Current
Wiper Resistance
Wiper Resistance
Voltage on any R
H
or R
L
Pin
Noise
Resolution
Absolute Linearity
(5)
Relative Linearity
(6)
Temperature Coefficient of R
POT
Ratiometric Temp. Coefficient
Potentiometer Capacitances
Frequency Response
Test Conditions
Min
Typ
100
50
10
2.5
±20
25°C, each pot
I
W
= ±3 mA @ V
CC
= 3 V
I
W
= ±3 mA @ V
CC
= 5 V
V
SS
= 0 V
(4)
R
W
(n)(actual) - R(n)(expected)
R
W
(n+1) - [R
W
(n) + LSB]
(8)
(4)
(4)
(4)
R
POT
= 50 kΩ
(4)
(8)
Ratings
-55 to +125
-65 to +150
-2.0 to +V
CC
+ 2.0
-0.2 to +7.0
1.0
300
±12
Units
ºC
°C
V
V
W
ºC
mA
Ratings
+2.5 to +6
-40 to +85
Units
V
°C
Max
Units
kΩ
kΩ
kΩ
kΩ
%
%
mW
mA
Ω
Ω
V
nV
√
Hz
%
LSB
(7)
LSB
(7)
ppm/ºC
ppm/ºC
pF
MHz
I
W
R
W
R
W
V
TERM
VN
200
100
GND
0.4
1
50
+3
300
150
V
CC
+1
+0.2
+300
20
10/10/25
0.4
TC
RPOT
TC
RATIO
C
H
/C
L
/C
W
fc
Notes:
(1) Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions outside of those listed in the operational sections of this
specification is not implied. Exposure to any absolute maximum rating for extended periods may affect device performance and reliability.
(2) The minimum DC input voltage is –0.5 V. During transitions, inputs may undershoot to –2.0 V for periods of less than 20 ns. Maximum
DC voltage on output pins is V
CC
+0.5 V, which may overshoot to V
CC
+2.0 V for periods of less than 20 ns.
(3) Latch-up protection is provided for stresses up to 100 mA on address and data pins from –1 V to V
CC
+1 V.
(4) This parameter is tested initially and after a design or process change that affects the parameter.
(5) Absolute linearity is utilized to determine actual wiper voltage versus expected voltage as determined by wiper position when used as a potentiometer.
(6) Relative linearity is utilized to determine the actual change in voltage between two successive tap positions when used as a potentio-
The pressure transmitter I use outputs a signal of 0.5v-4.5v. If I use 430f149 to collect the signal, I can only use an external voltage reference source. So what chip should I use? Can you recommend ...
1. When using MICROLIB, global variables are not initialized; 2. When not using MICROLIB, if you do not redefine _sys_exit(), you can see that the global variables are initialized correctly, but stop ...
[size=4]Due to the rapid development of microelectronics technology, digital electronic systems composed of IC chips are developing rapidly in the direction of large scale, small size and high speed, ...
If the use of single-function programmable power management ICs was ever manageable, that is a thing of the past. Many PCBs now typically use several multi-voltage devices, each with a different power...
At present, the development of wireless power supply technology for electric vehicles (EVs) is becoming more and more active. In 2012, Volvo of Sweden established Volvo Technology Japan in Tokyo as...[Details]
This program is written to simulate the serial port hardware mechanism. When used, a timed interrupt can be set with a time interval of 1/4 baud rate. The receiving function is called once for ea...[Details]
Remote keyless entry (RKE) systems have become popular with users, with more than 80% of new cars in North America and more than 70% in Europe equipped with RKE systems. In addition to the obvious ...[Details]
Automotive applications are particularly sensitive to EMI events, which are unavoidable in a noisy electrical environment consisting of a central battery, bundled wiring harnesses, various inductiv...[Details]
In order to highlight the concept of "energy saving and environmental protection" of intelligent buildings, solar street lights are designed for intelligent communities. The inclination and capacit...[Details]
DSP (digital signal processor) is used more and more frequently in today's engineering applications. There are three main reasons for this: first, it has powerful computing power and is capable of ...[Details]
Although it is relatively easy to check the stability of a simple amplifier at lower frequencies, it may be much more difficult to evaluate the stability of a more complex circuit. This artic...[Details]
1. Overview
The Virtual CAN Interface (VCI) function library is an application program interface specifically provided for the use of ZLGCAN devices on PCs. The functions in the library ar...[Details]
1. Project Introduction
Shandong Dezhou Xingtai Paper Co., Ltd. is a newly built high-end paperboard production enterprise with domestic leading level established by Shandong Zhaodongfang Pape...[Details]
The production process of lithium batteries does not mention the previous processes such as material preparation, winding, liquid injection, and packaging, but only talks about the final formation ...[Details]
1. Introduction
AS-Interface bus technology is an intelligent network that uses a single cable to connect sensors and actuators to controllers, transmit data, and provide power. It can be used...[Details]
1. Brief Introduction
With the continuous development and improvement of single-chip microcomputer technology, single-chip microcomputers have been widely used in all walks of life, and ...[Details]
UDN2916LB is a two-phase stepper motor bipolar driver integrated circuit launched by SANKEN. It can drive dual-winding bipolar stepper motors and is particularly suitable for controlling dual-step ...[Details]
Automotive electronics are in a noisy environment
,
so automotive electronics must have excellent electromagnetic compatibility (EMC) performance. The most important part of automotive elec...[Details]
The platemaking machine is an indispensable device in platemaking and printing, and plays a very important role. The platemaking machine is a device used to make printing plates. The principle is c...[Details]
Test/Measurement
京公网安备 11010802033920号
EEWORLD
