[attach ]656568[/attach]
Previously there was a Raspberry Pi:
But... there is no HDMI cable with a small head...
This time, I got the wires, the box, and even the antenna. Maybe I can have some fun wi...
SPI module introduction
Refer to 28. Serial Peripheral Interface (SPI) in Renesas RA2L1 Group User's Manual: Hardwarefeature2 channels
Supports full-duplex and send-only modes, 3-wire and 4-wire syste...
[i=s]This post was last edited by qinyunti on 2022-11-12 10:27[/i]Prepare
The prerequisite is that MDK and JLINK have been installed.
MDK version V5.37
JLINK version V7.82 (V7.5 or above)Development b...
A week's work is finally over. I work overtime until late every day and don't have much time to learn the Xingkong board. I quickly take advantage of the weekend to play with it.
As the saying goes, i...
In the previous review, we had a preliminary understanding of the hardware system of the Xingkong board. This article introduces several connection methods of the Xingkong board.The Xingkong board sup...
I want to use a SOT23 MOS tube to drive a 24V/180MA solenoid valve. The maximum power dissipation here is 2.5W, but 24*0.18=4.32W. Is it not enough?...
Traditional broadcasting systems generally need to be operated manually at a fixed time, and can only realize one-way broadcasting with few functions. Traditional bell ringing equipment has a singl...[Details]
Assume that data is read from 8-bit AD (if it is a higher-bit AD, the data type can be defined as int), the subroutine is get_ad();
1. Limited secondary filtering
/* A value can be adjust...[Details]
As a wireless broadband metropolitan area network standard, WiMAX technology has greater advantages than previous 3.5GHz MMDS products in terms of non-line-of-sight transmission and spectrum utiliz...[Details]
1. Circuit composition
The whole circuit consists of two parts:
1. Power saving control circuit
As shown in the figure below. Including delay circuit and drive circuit.
(1) Delay ci...[Details]
This article discusses how to wake up a touch-sensitive device such as a tablet without touching the device, using basic gesture recognition and novel proximity sensors. The article discusses the p...[Details]
1. Introduction
With the growth of parking demand, the scale of parking lots is becoming larger and larger. A lot of research has been done on intelligent parking lots in China, but most of th...[Details]
Floating-point digital signal processing has become a constant requirement for precision technology, often in applications requiring high accuracy in areas such as aviation, industrial machinery, a...[Details]
Converged processors meet scalability requirements
In current embedded system design, solutions based on MCU, DSP, FPGA and ASIC account for more than 90% of the market share. These solutions ...[Details]
introduction
In the discharge process of tokamak plasma physics, the study of rupture and sawtooth is of great significance. Rupture and sawtooth exist in most tokamaks. Rupture is a notew...[Details]
1 Introduction
Solar street lights are mainly composed of four parts: solar photovoltaic cell components, batteries, charge and discharge controllers, and lighting fixtures. The bo...[Details]
To differentiate their products in a crowded and competitive market, manufacturers of handheld devices often consider battery life and power management as key selling points for cell phones, PDAs, ...[Details]
July 11, 2012, Beijing - Altera Corporation (NASDAQ: ALTR) today announced the launch of 40-Gbps Ethernet (40GbE) and 100-Gbps Ethernet (100GbE) intellectual property (IP) core products. These core...[Details]
In the single-chip microcomputer system, in addition to display devices, sound devices are often used, and the most common sound device is the buzzer. Buzzers are generally used for some low-demand...[Details]
Overview
In spectral measurement, photomultiplier tubes (PMT) and charge-coupled devices (CCD) are often used as photoelectric converters. PMT is used in slow-changing, high-precision spectral...[Details]
Continuity test
A variety of devices need to be checked for continuity, including cable assemblies, printed circuit boards, and connectors to ensure that these components have the expected contin...[Details]