EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-GLHSC336N

Description
Transponder, 10000Mbps(Tx), 10000Mbps(Rx), SC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerLumentum Operations LLC
Download Datasheet Parametric View All

PH1-GLHSC336N Overview

Transponder, 10000Mbps(Tx), 10000Mbps(Rx), SC/UPC Connector,

PH1-GLHSC336N Parametric

Parameter NameAttribute value
MakerLumentum Operations LLC
Reach Compliance Codecompliant
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body height13.2 mm
Body length or diameter84.1 mm
Connection TypeSC/UPC CONNECTOR
Data rate (receive)10000 Mbps
Data rate (send)10000 Mbps
Emitter/Detector TypeAVALANCHE PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1544 nm
Nominal optical power output2.511 mW
minimum return loss-27 dB
Sensitivity-24 dBm
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
How to increase the operating frequency of the circuit
As designers, we certainly hope that the operating frequency of the circuit we design (unless otherwise specified, the operating frequency refers to the operating frequency within the FPGA chip) is as...
FPGA小牛 FPGA/CPLD
ucosii ported to STM32F107
I'm porting uCOSii to STM32F107 recently, and I've encountered some problems. The compiler I'm using is IAR6.4. The official DEMO uses Micrium_uC-Eval-STM32F107_uCOS-II. Download address: [url=http://...
tiaohan stm32/stm8
How do I attach a file when posting?
How do I post and attach files? How do I sell ChipCoin? Thanks....
西西西 Electronics Design Contest
Reprint power table
[[i] This post was last edited by tsb00 on 2009-3-22 13:40[/i]]...
tsb00 MCU
About the communication problem between arm9 and c5501dsp
When writing data to dsp, the control register and address register are all right, but when I use ccs to check the memory, there is no change. Reading data is also wrong. Please give me some advice!!!...
zhaojunlong1314 ARM Technology
Do I need to add magnetic beads to the input of a DC-DC power supply?
In designing a DC-DC power conversion circuit, the input power supply is shared with other analog circuits. In order to avoid The DC-DC part interferes with other analog circuits. Do I need to add a m...
通通 Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2404  2852  240  2049  1954  49  58  5  42  40 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号