Halogen and Antimony Free. “Green” Device (Note 3)
8
7
6
5
SET
NC
NC
V
IN
GND 4
U-DFN3030-10
( Top View )
CTRL
RSVD
NC
SW
1
2
3
4
5
10
9
SET
NC
NC
NC
V
IN
AP8800
8
7
6
Applications
Commercial & Industrial Lighting
Small LCD Panel Backlight
Architecture Detail Lighting
Appliances Interior Lighting
GND
Notes:
1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS), 2011/65/EU (RoHS 2) & 2015/863/EU (RoHS 3) compliant.
2. See https://www.diodes.com/quality/lead-free/ for more information about Diodes Incorporated’s definitions of Halogen- and Antimony-free, "Green" and
Lead-free.
3. Halogen and Antimony free "Green‖ products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total Br + Cl)
Switch Pin. Connect inductor/freewheeling diode here. Minimize trace area at this pin to
reduce EMI.
GND Pin
Set Nominal Output Current Pin. To configure the output current of the device.
Dual function dimming control pin.
Input voltage of 0.2V or lower forces the device into low current standby mode and
shuts off the output.
A PWM signal (driven by an open-drain/collector source) allows the output current
to be adjusted over a wide range up to 100%.
CTRL
1
1
1
An analog voltage between 0.3V and 2.5V adjusts the output current between 25%
and 200% of the current set by 0.2V/R
S
.
The input impedance is about 200kΩ, and if the pin is left open V
CTRL
= V
REF
V
IN
RSVD
NC
5
2
6, 7
5
2
6, 7
6
2
2, 7, 8, 9
Input Supply Pin. Must be locally bypassed.
Reserved. Normally connected to Ground
No Connection.
Functional Block Diagram
Absolute Maximum Ratings
(@T
A
= +25° unless otherwise specified.)
C,
Symbol
V
IN
V
SET
VSW
V
CTRL
T
J
T
LEAD
T
ST
Caution:
Parameter
VIN Pin Voltage
Set Voltage Relative to V
IN
SW Voltage
CTRL Pin Input Voltage
Maximum Junction Temperature
Maximum Lead Temperature
Storage Temperature Range
Rating
-0.3 to +30
V
IN
-5 to V
IN
+0.3
-0.3 to +30
-0.3 to +5
+125
+300
-55 to +125
Unit
V
V
V
V
°
C
°
C
°
C
Stresses greater than the 'Absolute Maximum Ratings' specified above, may cause permanent damage to the device. These are stress ratings only;
functional operation of the device at these or any other conditions exceeding those indicated in this specification is not implied. Device reliability may be
affected by exposure to absolute maximum rating conditions for extended periods of time.
Semiconductor devices are ESD sensitive and may be damaged by exposure to ESD events.
Suitable ESD precautions should be taken when handling and transporting these devices.
This course introduces the use of Xilinx's new generation development platform Vivado in detail. It is divided into two parts: introductory and advanced. It covers four major topics: design process, t...
AT89C51 is a low-voltage, high-performance CMOS 8-bit microprocessor with 4K bytes of flash programmable and erasable read-only memory (FPEROM), commonly known as a single-chip microcomputer. The devi...
I saw a lot of information about launch pad and wanted to learn it. Do I need to buy any peripherals to learn launch pad? For example, LCD, digital tube, etc.?...
In the programming of DSP28335, are the programming procedures for serial port 232 and 485 the same? Why can I use the same program to communicate with 232, but 485 can only send but not receive?...
I helped my cousin upgrade his computer today, and when I got home I found that the USB driver-free camera didn't work, and the screen was black. I searched online and downloaded a black screen patch,...
Microchip's PIC18F46J50 is a low-power, high-performance 8-bit USB microcontroller (MCU) using nanoWatt XLP technology. The current in deep sleep mode can be as low as 13nA, the operating voltage i...[Details]
Microcontrollers (MCUs), which are widely used in automotive electronics, are rapidly facing time and cost pressures. The main advantage of using MCUs has always been to create high-level system in...[Details]
Analog engineers have traditionally struggled with complexity when designing power supplies that required multiple outputs, dynamic load sharing, hot-swap, or extensive fault-handling capabilities....[Details]
In recent years, the market for mobile/portable devices such as smartphones and laptops has continued to grow rapidly. While these products continue to integrate more new features to enhance the ...[Details]
1. Introduction
Light control circuit plays a vital role in urban street lamps or corridor lighting. With light control circuit, the lights can be automatically turned on and off according to ...[Details]
The reason for the light decay of white LEDs: the decline of phosphor performance
So far, the rapid decline of the luminous performance of white light LEDs, especially low-power white light LE...[Details]
Two simple circuits are implemented to drive two LEDs from a battery powered microprocessor.
This design is based on a circuit that uses three resistors and a microprocessor I/O pin as an input h...[Details]
With the continuous improvement of the requirements of intelligent building security systems and the continuous improvement of people's safety awareness, indoor anti-theft has gradually attracted peop...[Details]
We know that microcontroller development tools generally include real-time online emulators and programmers. Among them, online emulators are very good tools, but they are also more expensive...[Details]
Microcalorimetry
is used to determine energy relationships. Microcalorimetry techniques are often required when performing calorimetric experiments with small sample sizes or slow heating rat...[Details]
General LED lighting has a current limiting resistor in the driving circuit, and the power consumed by the resistor has nothing to do with the LED light emission. In order to improve efficiency, a...[Details]
LED technology has made rapid progress, and improvements in chip design and materials have promoted the development of brighter and more durable light sources, and the scope of light source applica...[Details]
The TPS92210 is a single-stage LED lighting pulse width modulation (PWM) controller. The TRIAC dimmable solution not only regulates the LED current, but also achieves a power factor close to 1. The...[Details]
Since AC mains power may experience power outages, voltage sags and surges, continuous undervoltage and overvoltage, and frequency fluctuations during supply, these factors will affect the continuous ...[Details]
Introduction
As the country increases its efforts to control the atmospheric environment, motorcycle emission regulations will become stricter year by year, and motorcycles that do not meet the...[Details]
Training Edition
京公网安备 11010802033920号
EEWORLD
