EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-FLALC3322

Description
Transponder, 10660Mbps(Tx), 10660Mbps(Rx), LC/SPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerJDS Uniphase Corporation ( VIAVI )
Websitehttp://www.jdsu.com/index.html
Download Datasheet Parametric View All

PH1-FLALC3322 Overview

Transponder, 10660Mbps(Tx), 10660Mbps(Rx), LC/SPC Connector,

PH1-FLALC3322 Parametric

Parameter NameAttribute value
MakerJDS Uniphase Corporation ( VIAVI )
Reach Compliance Codeunknown
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body height13.2 mm
Body length or diameter84.1 mm
Connection TypeLC/SPC CONNECTOR
Data rate (receive)10660 Mbps
Data rate (send)10660 Mbps
Emitter/Detector TypeAVALANCHE PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1543 nm
Nominal optical power output1.584 mW
minimum return loss-27 dB
Sensitivity-24 dBm
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
EEWORLD University Hall----VertiGo, a wall-climbing robot
Wall-climbing robot VertiGo : https://training.eeworld.com.cn/course/4322Disney Research and ETH Zurich have jointly developed a wall-climbing robot called Vertigo, which can climb vertical walls like...
老白菜 Robotics Development
WINCE simple question
Could you please tell me how to use the dynamic library written in VC in WinCE? It would be best if you can give more detailed steps. Thank you!...
z9x386 Embedded System
Is this the correct way to receive SSP data?
I am currently using the SSP port of LPC1114 to communicate with an AD. This AD has four channels, but currently I am sending the "VOLTAGE" channel to convert this channel. However, the data stored in...
milan111 NXP MCU
Please help, about the two interrupt modes of ARM7 s3c44b0
The datesheet of s3c44b0 says that there are two modes for interrupt jumps, non-vectored interrupt mode and vectored interrupt mode. So where should the non-vectored interrupt mode code segment be pla...
pansy413 ARM Technology
In our security field, let’s talk about what multimeters can be used for?
Tell us about your understanding of multimeters and in what situations can they be used! ! I have tested whether the network cable is connected. What have you used it for?...
banana Industrial Control Electronics
Shunchip RK3288 development and design
[align=left][color=#000000][font=Calibri] [b]RK3288[/b][/font][b]Baseboard[/b][b][font=Calibri]+[/font][/b][b]Core Board Design Process[/b][/color][/align] [align=left][b][font=Calibri][color=#000000]...
qq7643066 PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1399  1392  470  1646  886  29  10  34  18  45 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号