EEWORLDEEWORLDEEWORLD

Part Number

Search

MIC803-40D2VC3

Description
1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3
CategoryPower/power management    The power supply circuit   
File Size251KB,10 Pages
ManufacturerMicrochip
Websitehttps://www.microchip.com
Download Datasheet Parametric View All

MIC803-40D2VC3 Overview

1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3

MIC803-40D2VC3 Parametric

Parameter NameAttribute value
MakerMicrochip
package instruction2 X 2.10 MM, SC-70, 3 PIN
Reach Compliance Codecompli
ECCN codeEAR99
Other featuresRESET THRESHOLD VOLTAGE IS 4V
Adjustable thresholdNO
Analog Integrated Circuits - Other TypesPOWER SUPPLY SUPPORT CIRCUIT
JESD-30 codeR-PDSO-G3
length2.025 mm
Number of channels1
Number of functions1
Number of terminals3
Maximum operating temperature125 °C
Minimum operating temperature-40 °C
Package body materialPLASTIC/EPOXY
encapsulated codeTSSOP
Package shapeRECTANGULAR
Package formSMALL OUTLINE, THIN PROFILE, SHRINK PITCH
Certification statusNot Qualified
Maximum seat height1.1 mm
Maximum supply voltage (Vsup)5.5 V
Minimum supply voltage (Vsup)1.2 V
Nominal supply voltage (Vsup)5 V
surface mountYES
Temperature levelAUTOMOTIVE
Terminal formGULL WING
Terminal pitch0.65 mm
Terminal locationDUAL
width1.25 mm
MIC803
3-Pin Microprocessor Supervisor Circuit
with Open-Drain Reset Output
General Description
The MIC803 is a single-voltage supervisor with open-drain
reset output that provides accurate power supply
monitoring and reset generation in microprocessor based
systems. The function of the device is to assert a reset
signal if the power supply voltage drops below the Reset
Threshold voltage, and retain this reset for the Reset
Timeout Period once the power supply increases above
the Reset Threshold voltage.
The MIC803 consumes only 4.5μA of supply current and
offers three reset delay periods of 20ms, 140ms and
1120ms (min). It features factory programmed reset
threshold levels from 2.63V to 4.63V to accommodate
3.0V, 3.3V, and 5.0V power supplies. It is available in the
compact 3-pin SC-70 and SOT-23 packages.
Features
4.5μA supply current (typical) at 3.6V
Open-Drain /RESET output
/RESET remains valid with V
CC
as low as 1V
20ms, 140ms, or 1120ms (min) reset timeout Options
2.63V to 4.63V Preset Voltage Threshold Options
2.5% Voltage Threshold Accuracy over temperature
3-pin SC70-3 package (2.0mm x 2.1mm)
3-pin SOT-23 package (2.3mm x 2.9mm)
-40˚C to +125˚C Junction Temperature Range
Applications
Critical microcomputer power monitoring
Portable equipment
Solid state drives
Printers/computers
Embedded controllers
____________________________________________________________________________________________________________
Typical Application
V
CC
V
CC
V
CC
100k
MIC803
RESET
GND
RESET
µP
GND
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 •
http://www.micrel.com
December 2010
M9999-122310-A
Design of JPEG Image Compression Based on DSP
I. Introduction The JPEG algorithm is a digital image compression coding algorithm with the characteristics of high compression ratio and low distortion, and has been determined as an international st...
Jacktang DSP and ARM Processors
Telnet problem under vxworks
The target machine has a telnet server component, which is downloaded and run. The host (XP) can log in from DOS. However, if the RLOGIN/telnet password protection component is added, there is no resp...
less_than Real-time operating system RTOS
Where does the program run during 2407 hardware emulation?
I am a novice. I used to use an ad, which did not require hardware simulation. The program was directly downloaded to the program RAM through the serial port for debugging and running. Now when 2407 i...
ZUNZHONG Microcontroller MCU
How to partition Nand Flash when the system does not have BinFS
I didn't use BinFS, but after I loaded the Flash driver, I found that there was a drive letter under My Device, which was consistent with the folder value set in my registry, and the size was about 24...
abncat Embedded System
Explanation of the parameters and terms of the power module
[align=left][color=rgb(85, 85, 85)][font=微软雅黑][size=12px]In the power module technical manual provided by the manufacturer, there are generally a lot of parameter data. The main parameter terms are ex...
tgd343310381 Power technology
How to switch from NetworkManager to systemd on Linux
How to Switch from NetworkManager to systemd on Linux In the Linux world, the adoption of systemd has been a subject of intense debate, with the flames of war still raging between its supporters and o...
奋斗之路 Linux and Android

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2004  71  2406  2276  2017  41  2  49  46  52 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号