EEWORLDEEWORLDEEWORLD

Part Number

Search

MCP14E6T

Description
2.0A Dual High-Speed Power MOSFET Driver With Enable
File Size654KB,31 Pages
ManufacturerMicrochip
Websitehttps://www.microchip.com
Download Datasheet Compare View All

MCP14E6T Overview

2.0A Dual High-Speed Power MOSFET Driver With Enable

MCP14E6/7/8
2.0A Dual High-Speed Power MOSFET Driver With Enable
Features
• High Peak Output Current: 2.0A (typical)
• Independent Enable Function for Each Driver
Output
• Wide Input Supply Voltage Operating Range:
- 4.5V to 18V
• Low Shoot-Through/Cross-Conduction Current in
Output Stage
• High Capacitive Load Drive Capability:
- t
R
: 12 ns with 1000 pF load (typical)
- t
F
: 15 ns with 1000 pF load (typical)
• Short Delay Times: 45 ns (typical)
• Low Supply Current:
- With Logic ‘1’ Input/Enable – 1 mA (typical)
- With Logic ‘0’ Input/Enable – 300 µA (typical)
• Latch-up Protected: Passed JEDEC JESD78A
• Logic Input will Withstand Negative Swing,
up to 5V
• Space-Saving Packages:
- 8-Lead SOIC, PDIP, 6x5 DFN
General Description
The MCP14E6/7/8 devices are high-speed MOSFET
drivers, capable of providing 2.0A of peak current. The
dual inverting, dual non-inverting and complementary
outputs are directly controlled from either TTL or
CMOS (3V to 18V). These devices also feature low
shoot-through current, fast rise/fall times and
propagation delays, which make them ideal for high
switching frequency applications.
The MCP14E6/7/8 devices operate from a 4.5V to 18V
single power supply and can easily charge and
discharge 1000 pF of MOSFET gate capacitance. They
provide low enough impedances, in both the ON and
OFF states, to ensure the MOSFETs’ intended state
will not be affected, even by large transients.
The additional control of the MCP14E6/7/8 outputs is
allowed by the use of separate enable functions. The
ENB_A and ENB_B pins are active-high and are
internally pulled up to V
DD
. The pins may be left floating
for standard operation.
The MCP14E6/7/8 dual output, 2.0A driver family is
offered in both surface-mount and pin-through-hole
packages with a -40
o
C to +125
o
C temperature rating.
The low thermal resistance of the thermally enhanced
DFN package allows greater power dissipation
capability for driving heavier capacitive or resistive
loads.
These devices are highly latch-up resistant under any
conditions within their power and voltage ratings. They
are not subject to damage when up to 5V of noise
spiking (of either polarity) occurs on the ground pin.
The devices are fully latch-up protected when tested
according to JEDEC JESD78A. All terminals are fully
protected against Electrostatic Discharge (ESD), up to
4 kV (HBM) or 400V (MM).
Applications
Switch Mode Power Supplies
Pulse Transformer Drive
Line Drivers
Motor and Solenoid Drive
©
2011 Microchip Technology Inc.
DS25006A-page 1

MCP14E6T Related Products

MCP14E6T MCP14E8 MCP14E6 MCP14E7
Description 2.0A Dual High-Speed Power MOSFET Driver With Enable 2.0A Dual High-Speed Power MOSFET Driver With Enable 2.0A Dual High-Speed Power MOSFET Driver With Enable 2.0A Dual High-Speed Power MOSFET Driver With Enable
WinCE5.0 system automatically recognizes USB flash drive after startup?
WinCE5.0 system automatically recognizes USB flash drive after startup? Now I want to ask everyone, when using WinCE5.0, when the system is not started, plug in the USB flash drive, and after WinCE is...
smilesmile13 Embedded System
TI's CC2541DK-SENSOR shipments delayed
I just received an email from TI. The CC2541DK-SENSOR that was originally scheduled to be shipped yesterday (September 5) has now been changed to September 13. I wonder if this is the case with you to...
眼大5子 Analogue and Mixed Signal
Problem with eeprom in AVR
I use mega128 to operate its eeprom, and I can write data. The problem is that after I write the data, I can read it, but after I assign the initial value, I read it and it is not the original value I...
duxuetao Microchip MCU
Why does CC2530's PWM have to use standby position 2?
When learning CC2530, I found that everyone uses spare position 2. The original channels of timer 1 are P02, P03, P04, P05, P06. Why must we use P2, P1, P0, P7, P6? Can we use position 1? Please expla...
flying510 RF/Wirelessly
【Goodbye 2021, Hello 2022】The first time in 2021
This is the first post of 2022, recording the past events of 2021 and my aspirations for 2022! I changed jobs for the first time in 2021. Although my previous job was comfortable, the comfort made me ...
PowerWorld Talking
DDS
DDS has the following advantages: ⑴ High frequency resolution, multiple output frequency points, up to frequency points (N is the number of phase accumulator bits); ⑵ Fast frequency switching speed, u...
285506445 MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2646  1447  1668  1597  56  54  30  34  33  2 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号