Data are valid at +25°C, unless otherwise specified.
Limit or
typical
Industrial
Grade
Parameter
Input
Nominal input voltage
Permanent input
voltage range (Ui)
Start up time*
Conditions
Units
Single Output MGDSI-04
04 - C
04 - I
24
18- 36
200
Full temperature range
Full temperature range
Ui max.
Nominal output
Full load : resistive
Ui nominal, full load at switching
freq. BW = 20MHz
Decoupling capacitor 10µF
Ui nominal
Short-circuit
Ui nominal
No load
Nominal
Min. - Max.
Maximum*
VDC
VDC
ms
5
4,5- 5,5
200
Reflected ripple current
Input current in short
circuit mode (Average)
No load input current
Output
Output voltage
Typical
Maximum
Maximum
mApp
mA
mA
50
50
50
30
30
30
Ui min. to max.
Ambient temperature : +25°c
Ui nominal, 75% load
At 105°c baseplate
Ui min. to max.
Full temperature range
Ui min. to max.
Nominal
Nominal
Nominal
Nominal
Maximum
Maximum
Maximum
Maximum
Maximum
Maximum
Maximum
Maximum
Maximum
Typical
Typical
Typical
VDC
VDC
VDC
VDC
%
W
mA
mA
mA
mA
mVpp
mVpp
mVpp
%
%
%
3,3
5
12
15
+/- 2
4
1 000
800
330
260
50
100
150
+/- 1
+/- 2,5
76
3,3
5
12
15
+/- 2
4
1 000
800
330
260
50
100
150
+/- 1
+/- 2,5
78
Set Point accuracy
Output power
Output current
3,3V output
5V output
12V output
15V output
Ripple output voltage **
3,3V and 5V output
12V output
15V output
Line regulation
Load regulation ***
Efficiency
Maximum admissible
Capacitive load
3,3V and 5V output
12V and 15V output
5
Ui nominal
Full load
BW = 20MHz
Ui min. to max.
Full load
Ui nominal
25% to full load
Ui nominal
Full load
Ui nominal
Full load
Per output
Maximum
Maximum
µF
µF
1 000
47
1 000
47
Note* : The start-up time is the time between start of the module through on/off release, input voltage present, and output voltage settled; for modules without on/
off function start up time value is an indicative value and not a maximum value.
Note ** : The ripple output voltage is the periodic AC component imposed on the output voltage, an aperiodic and random component (noise) has also to be considered.
This noise can be reduced by adding an external capacitor (typically 10µF/rated voltage depending on isolation requirement) connected between the pin Gin and the
pin Gout of the converter. This capacitor should be layed-out as close as possible from the converter.
Note *** : For load regulation characteristics from 0% to full load, please contact factory.
Data are valid at +25°C, unless otherwise specified.
Limit or
typical
Industrial
Grade
Parameter
Input
Nominal input voltage
Permanent input
voltage range (Ui)
Start up time*
Conditions
Units
Bi Output MGDBI- 04
04 - C
04 - I
24
18- 36
200
Full temperature range
Full temperature range
Ui max.
Nominal output
Full load : resistive
Ui nominal, full load at switching
freq. BW = 20MHz
Decoupling capacitor 10µF
Ui nominal
Short-circuit
Ui nominal
No load
Nominal
Min. - Max.
Maximum*
VDC
VDC
ms
5
4,5- 5,5
200
Reflected ripple current
Input current in short
circuit mode (Average)
No load input current
Output
Output voltage
Set Point accuracy
Output power
Output current
+/- 5V output
+/- 12V output
+/- 15V output
Ripple output voltage **
5V output
12V output
15V output
Line regulation
Load regulation ***
Cross load output
regulation
Efficiency
Maximum admissible
Capacitive load
5V output
12V and 15V output
Typical
Maximum
Maximum
mApp
mA
mA
50
50
50
30
30
30
Ui min. to max.
Ambient temperature : +25°c
Ui nominal, 75% load
At 105°c baseplate
Ui min. to max.
Full temperature range
Ui min. to max.
Ui nominal
Full load
BW = 20MHz
Ui min. to max.
Full load
Ui nominal
25% to full load
Ui nominal
+ Vout nominal load
- Vout from 25% to full load
Ui nominal
Full load
Ui nominal
Full load
Per output
Nominal
Nominal
Nominal
Maximum
Maximum
Maximum
Maximum
Maximum
Maximum
Maximum
Maximum
Typical
Typical
Typical
Typical
VDC
VDC
VDC
%
W
mA
mA
mA
mVpp
mVpp
mVpp
%
%
%
%
+/- 5
+/- 12
+/- 15
+/- 2
+/- 2
+/- 400
+/- 165
+/- 130
50
100
150
+/- 1
+/- 2,5
+/- 0,5
76
+/- 5
+/- 12
+/- 15
+/- 2
+/- 2
+/- 400
+/- 165
+/- 130
50
100
150
+/- 1
+/- 2,5
+/- 0,5
78
5
Maximum
Maximum
µF
µF
470
22
470
22
Note* : The start-up time is the time between start of the module through on/off release, input voltage present, and output voltage settled; for modules without on/
off function start up time value is an indicative value and not a maximum value.
Note ** : The ripple output voltage is the periodic AC component imposed on the output voltage, an aperiodic and random component (noise) has also to be considered.
This noise can be reduced by adding an external capacitor (typically 10µF/rated voltage depending on isolation requirement) connected between the pin Gin and the
pin Gout of the converter. This capacitor should be layed-out as close as possible from the converter.
Note *** : For load regulation characteristics from 0% to full load, please contact factory.
Please help me find out if there is anything wrong with the program I wrote. The current situation is that after downloading it to the microcontroller, the first digital tube displays a zero, and then...
CC1120 Sub1G Development Kit Hands-on Practice : https://training.eeworld.com.cn/course/313Based on the CC1120 development kit from Xinwei Technology, this video series demonstrates how to use SmartRF...
On July 13, 2005, Renesas Technology Corporation officially launched the Renesas Forum 2005, the first stop of the three-city (Beijing, Shanghai, Shenzhen) China tour seminar, at the Beijing Lufthansa...
I don't quite understand. I'm a beginner. I want to try this. But I don't know where to start. Did I draw the circuit diagram myself? Or did I find it online? I can't draw it myself. Can anyone help m...
I have a question for you. Regarding the JTAG circuit of TI CC2530. Generally, when P2.1 and P2.2 are used for JTAG, they cannot be used for other functions. But when P1.4, P1.5 and P1.6 are used as J...
introduction
In the discharge process of tokamak plasma physics, the study of rupture and sawtooth is of great significance. Rupture and sawtooth exist in most tokamaks. Rupture is a notew...[Details]
System design is a complex process. It is not enough to just use ICs. There are many details to consider. This article uses a high-fidelity music playback system as an example to introduce how to s...[Details]
In this article, the high-performance DSP developed by TI can be used as an effective confidentiality method if it is applied to PC encryption cards.
As an effective network security solution,...[Details]
1 Introduction
With the acceleration of the pace of urban modernization, society has higher requirements for urban road lighting and urban lighting projects. The state has clearly required tha...[Details]
This paper designs a dot matrix LED text display screen that is easy to update, expandable, and low-cost. The way to reduce costs is
① Use the Bluetooth data transmission function of mobile ph...[Details]
When choosing a laptop battery, you should consider several factors, such as power, appearance, and quality.
Regarding power, we often see that a manufacturer uses values such as the number ...[Details]
Contact resistance
is the resistance to current flow through a closed pair of contacts. This type of measurement is performed on devices such as connectors,
relays
, and switches. The...[Details]
1 Introduction to HART Protocol
HART (Highway Addressable Remote Transducer), an open communication protocol for addressable remote sensor high-speed channels, was launched by Rosemen in the U...[Details]
This week, Microsoft held its 2012 Microsoft Worldwide Partner Conference (WPC) in Toronto, Canada. At the conference, Microsoft showed its new products and services to partners around the world. A...[Details]
PV inverter manufacturer SMA has launched its first DC arc fault circuit interrupter (AFCI) PV inverter and has received UL certification.
The new SunnyBoy AFCI inverter models include 3000-US...[Details]
The automotive lighting and signal control system is responsible for controlling the vehicle's lighting, signal lights, electric horns, reversing and brake buzzers. Traditional automotive lighting...[Details]
The typical fault troubleshooting listed below is for reference of maintenance personnel.
When the computer is turned on, the indicator light is off and there is no screen display
Mainte...[Details]
Continuity test
A variety of devices need to be checked for continuity, including cable assemblies, printed circuit boards, and connectors to ensure that these components have the expected contin...[Details]
hint:
The number of speakers and their spacing limit the sound field of a portable stereo system.
Spatial audio attempts to artificially recreate the experience of listening to sounds i...[Details]
Spatial Division Multiplexing (SDM) MIMO processing can significantly improve spectrum efficiency and thus greatly increase the capacity of wireless communication systems. Spatial Division Multip...[Details]
51mcu
京公网安备 11010802033920号
EEWORLD
