Data are valid at +25°C, unless otherwise specified.
Limit or
typical
Industrial
Grade
Parameter
Input
Nominal input voltage
Permanent input
voltage range (Ui)
Start up time*
Conditions
Units
Single Output MGDSI-04
04 - C
04 - I
24
18- 36
200
Full temperature range
Full temperature range
Ui max.
Nominal output
Full load : resistive
Ui nominal, full load at switching
freq. BW = 20MHz
Decoupling capacitor 10µF
Ui nominal
Short-circuit
Ui nominal
No load
Nominal
Min. - Max.
Maximum*
VDC
VDC
ms
5
4,5- 5,5
200
Reflected ripple current
Input current in short
circuit mode (Average)
No load input current
Output
Output voltage
Typical
Maximum
Maximum
mApp
mA
mA
50
50
50
30
30
30
Ui min. to max.
Ambient temperature : +25°c
Ui nominal, 75% load
At 105°c baseplate
Ui min. to max.
Full temperature range
Ui min. to max.
Nominal
Nominal
Nominal
Nominal
Maximum
Maximum
Maximum
Maximum
Maximum
Maximum
Maximum
Maximum
Maximum
Typical
Typical
Typical
VDC
VDC
VDC
VDC
%
W
mA
mA
mA
mA
mVpp
mVpp
mVpp
%
%
%
3,3
5
12
15
+/- 2
4
1 000
800
330
260
50
100
150
+/- 1
+/- 2,5
76
3,3
5
12
15
+/- 2
4
1 000
800
330
260
50
100
150
+/- 1
+/- 2,5
78
Set Point accuracy
Output power
Output current
3,3V output
5V output
12V output
15V output
Ripple output voltage **
3,3V and 5V output
12V output
15V output
Line regulation
Load regulation ***
Efficiency
Maximum admissible
Capacitive load
3,3V and 5V output
12V and 15V output
5
Ui nominal
Full load
BW = 20MHz
Ui min. to max.
Full load
Ui nominal
25% to full load
Ui nominal
Full load
Ui nominal
Full load
Per output
Maximum
Maximum
µF
µF
1 000
47
1 000
47
Note* : The start-up time is the time between start of the module through on/off release, input voltage present, and output voltage settled; for modules without on/
off function start up time value is an indicative value and not a maximum value.
Note ** : The ripple output voltage is the periodic AC component imposed on the output voltage, an aperiodic and random component (noise) has also to be considered.
This noise can be reduced by adding an external capacitor (typically 10µF/rated voltage depending on isolation requirement) connected between the pin Gin and the
pin Gout of the converter. This capacitor should be layed-out as close as possible from the converter.
Note *** : For load regulation characteristics from 0% to full load, please contact factory.
Data are valid at +25°C, unless otherwise specified.
Limit or
typical
Industrial
Grade
Parameter
Input
Nominal input voltage
Permanent input
voltage range (Ui)
Start up time*
Conditions
Units
Bi Output MGDBI- 04
04 - C
04 - I
24
18- 36
200
Full temperature range
Full temperature range
Ui max.
Nominal output
Full load : resistive
Ui nominal, full load at switching
freq. BW = 20MHz
Decoupling capacitor 10µF
Ui nominal
Short-circuit
Ui nominal
No load
Nominal
Min. - Max.
Maximum*
VDC
VDC
ms
5
4,5- 5,5
200
Reflected ripple current
Input current in short
circuit mode (Average)
No load input current
Output
Output voltage
Set Point accuracy
Output power
Output current
+/- 5V output
+/- 12V output
+/- 15V output
Ripple output voltage **
5V output
12V output
15V output
Line regulation
Load regulation ***
Cross load output
regulation
Efficiency
Maximum admissible
Capacitive load
5V output
12V and 15V output
Typical
Maximum
Maximum
mApp
mA
mA
50
50
50
30
30
30
Ui min. to max.
Ambient temperature : +25°c
Ui nominal, 75% load
At 105°c baseplate
Ui min. to max.
Full temperature range
Ui min. to max.
Ui nominal
Full load
BW = 20MHz
Ui min. to max.
Full load
Ui nominal
25% to full load
Ui nominal
+ Vout nominal load
- Vout from 25% to full load
Ui nominal
Full load
Ui nominal
Full load
Per output
Nominal
Nominal
Nominal
Maximum
Maximum
Maximum
Maximum
Maximum
Maximum
Maximum
Maximum
Typical
Typical
Typical
Typical
VDC
VDC
VDC
%
W
mA
mA
mA
mVpp
mVpp
mVpp
%
%
%
%
+/- 5
+/- 12
+/- 15
+/- 2
+/- 2
+/- 400
+/- 165
+/- 130
50
100
150
+/- 1
+/- 2,5
+/- 0,5
76
+/- 5
+/- 12
+/- 15
+/- 2
+/- 2
+/- 400
+/- 165
+/- 130
50
100
150
+/- 1
+/- 2,5
+/- 0,5
78
5
Maximum
Maximum
µF
µF
470
22
470
22
Note* : The start-up time is the time between start of the module through on/off release, input voltage present, and output voltage settled; for modules without on/
off function start up time value is an indicative value and not a maximum value.
Note ** : The ripple output voltage is the periodic AC component imposed on the output voltage, an aperiodic and random component (noise) has also to be considered.
This noise can be reduced by adding an external capacitor (typically 10µF/rated voltage depending on isolation requirement) connected between the pin Gin and the
pin Gout of the converter. This capacitor should be layed-out as close as possible from the converter.
Note *** : For load regulation characteristics from 0% to full load, please contact factory.
GND is the abbreviation of the ground terminal of the wire. It represents the ground wire or the zero wire. GND (Ground) on the circuit diagram and the circuit board represents the ground wire or the ...
[font=宋体][size=6][color=blue]I am using CCS5.1, and the target board is 5529 Launchpad. Has anyone encountered this problem? The serial port is recognized. [/color][/size][/font]...
As shown in the figure, the 10khz peripheral circuit has a duty cycle of about 0.15. How to reduce its duty cycle? Attached is its data sheet: https://wenku.baidu.com/view/d5edb5bd05a1b0717fd5360cba1a...
If I set the serial port receive FIFO to a depth of 7/8 and set the receive FIFO interrupt and receive timeout interrupt, when the length of the data received by my serial port is an integer multiple ...
[align=left][color=#000]Has anyone designed their own board based on the design drawing of the [color=rgb(205, 23, 31)][url=http://www.ti.com.cn/tool/cn/TMDSPLCKITV4-CEN]TMDSPLCKITV4-CEN[/url][/color]...
[font=PMingLiU][size=10.5pt]Nowadays, people are very concerned about their health and hope to have a good body. Body temperature is one of the important physiological parameters of the human body, an...
High efficiency and low standby power consumption are two major challenges in today's switching power supply design. Resonant topology or LLC topology is becoming increasingly popular because it ca...[Details]
Hardware designers have begun to adopt FPGA technology in high-performance DSP designs because it can provide 10-100 times faster computing than PC-based or microcontroller-based solutions. Previou...[Details]
introduction
With the continuous optimization of surface mount technology (SMT) and the rapid development of chip component manufacturing technology, the application of chip mounters in the el...[Details]
1. Introduction
Automobile pollution is one of the most important issues that people are most concerned about and need to solve urgently. As an important method for detecting automobile exhau...[Details]
At present, the traffic congestion in cities is quite serious. According to relevant news reports: In China, the traffic congestion has expanded from megacities such as Beijing, Shanghai, and Guang...[Details]
Do you often have to add brake fluid to your car's brakes? The fact that you need to pump out the brake fluid to make sure there is no gas in the brake fluid line may not be done by the car owner h...[Details]
In recent years, the market for mobile/portable devices such as smartphones and laptops has continued to grow rapidly. While these products continue to integrate more new features to enhance the ...[Details]
In this article, the high-performance DSP developed by TI can be used as an effective confidentiality method if it is applied to PC encryption cards.
As an effective network security solution,...[Details]
1. Introduction
Light control circuit plays a vital role in urban street lamps or corridor lighting. With light control circuit, the lights can be automatically turned on and off according to ...[Details]
For a long time, due to the limitation of hardware conditions, the display devices of traditional small handheld devices such as PDA are usually monochrome LCD, and the user interface is very simpl...[Details]
To differentiate their products in a crowded and competitive market, manufacturers of handheld devices often consider battery life and power management as key selling points for cell phones, PDAs, ...[Details]
July 11, 2012, Beijing - Altera Corporation (NASDAQ: ALTR) today announced the launch of 40-Gbps Ethernet (40GbE) and 100-Gbps Ethernet (100GbE) intellectual property (IP) core products. These core...[Details]
1 Introduction
As an emerging microfabrication technology, micro-electromechanical system (MEMS) technology has begun to be applied in various fields. It can integrate functions such as inform...[Details]
With the development and widespread application of computer technology, especially in the field of industrial control, computer communication is particularly important. Although serial communication g...[Details]
Contact resistance
is the resistance to current flow through a closed pair of contacts. This type of measurement is performed on devices such as connectors,
relays
, and switches. The...[Details]
Power technology
京公网安备 11010802033920号
EEWORLD
