531QB819M000DGR datasheet, PDF

Datasheet> All Categories > Passive components> oscillator> 531QB819M000DGR

531QB819M000DGR: DescriptionCMOS/TTL Output Clock Oscillator, 819MHz Nom, ROHS COMPLIANT, SMD, 6 PIN; CategoryPassive components oscillator; File Size215KB，12 Pages; ManufacturerSilicon Laboratories Inc; Environmental Compliance

Download Datasheet Parametric View All

531QB819M000DGR Overview

CMOS/TTL Output Clock Oscillator, 819MHz Nom, ROHS COMPLIANT, SMD, 6 PIN

531QB819M000DGR Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Maker	Silicon Laboratories Inc
Reach Compliance Code	unknown
Other features	TAPE AND REEL
maximum descent time	0.35 ns
Frequency Adjustment - Mechanical	NO
frequency stability	20%
JESD-609 code	e4
Manufacturer's serial number	531
Installation features	SURFACE MOUNT
Nominal operating frequency	819 MHz
Maximum operating temperature	85 °C
Minimum operating temperature	-40 °C
Oscillator type	CMOS/TTL
physical size	7.0mm x 5.0mm x 1.85mm
longest rise time	0.35 ns
Maximum supply voltage	3.63 V
Minimum supply voltage	2.97 V
Nominal supply voltage	3.3 V
surface mount	YES
maximum symmetry	55/45 %
Terminal surface	Nickel/Gold (Ni/Au)

Preview

Download Datasheet

View All

S i 5 3 0 / 5 31

EVISION

R Y S TA L

S C I L L A T O R

(XO)

(10 M H

Z T O

1.4 G H

)

Features

Available with any-rate output

frequencies from 10 MHz to 945 MHz

and select frequencies to 1.4 GHz

3rd generation DSPLL

with superior

jitter performance

3x better frequency stability than

SAW-based oscillators

Internal fixed crystal frequency

ensures high reliability and low

aging

Available CMOS, LVPECL,

LVDS, and CML outputs

3.3, 2.5, and 1.8 V supply options

Industry-standard 5 x 7 mm

package and pinout

Pb-free/RoHS-compliant

Si5602

Ordering Information:

See page 7.

Applications

SONET/SDH

Networking

SD/HD video

Test and measurement

Clock and data recovery

FPGA/ASIC clock generation

Pin Assignments:

See page 6.

(Top View)

GND

Description

The Si530/531 XO utilizes Silicon Laboratories’ advanced DSPLL circuitry

to provide a low jitter clock at high frequencies. The Si530/531 is available

with any-rate output frequency from 10 to 945 MHz and select frequencies to

1400 MHz. Unlike a traditional XO, where a different crystal is required for

each output frequency, the Si530/531 uses one fixed crystal to provide a

wide range of output frequencies. This IC based approach allows the crystal

resonator to provide exceptional frequency stability and reliability. In addition,

DSPLL clock synthesis provides superior supply noise rejection, simplifying

the task of generating low jitter clocks in noisy environments typically found in

communication systems. The Si530/531 IC based XO is factory configurable

for a wide variety of user specifications including frequency, supply voltage,

output format, and temperature stability. Specific configurations are factory

programmed at time of shipment, thereby eliminating long lead times

associated with custom oscillators.

CLK–

CLK+

Si530 (LVDS/LVPECL/CML)

GND

Functional Block Diagram

CLK– CLK+

CLK

Si530 (CMOS)

Fixed

Frequency

Any-rate

10–1400 MHz

DSPLL

Clock

Synthesis

GND

CLK–

CLK+

Si531 (LVDS/LVPECL/CML)

GND

Rev. 1.1 6/07

Si530/531

Recommended Resources

Two basic circuits of photorelay c

Condenser microphone FM circuit

Carrier transmitting circuit of cable broadcast disconnection monitor

STK0030 power amplifier circuit

Overvoltage automatic power-off device

Computer motherboard circuit diagram 815 4_43

Proteus simulates serial port data transmission and reception, and no need to press the power switch of the development board again and again: Without further ado, here is the pictureThe serial port receives an array of 16 bytes and displays it. 1. Install the virtual serial port software VSPD. Of course, there are other virtual serial port ...; ning_dan 51mcu

Lithium battery protection circuit for power MOS tube: Usually, due to the characteristics of lithium iron phosphate batteries, their charging and discharging processes need to be protected in applications to avoid overcharging, over-discharging or overhe...; qwqwqw2088 Power technology

Analog divider single power supply low power consumption everyone recommend a chip: I am new to analog circuits and want to make an analog divider, but the power supply needs low power consumption, low noise, and four quadrants. Can you recommend a film? Thank you....; thekobeking123 Analog electronics

2012 Hunan Province TI Design Competition Exchange Group: I hope that all students who participated in the 2012 Hunan TI will join this group to learn from each other. The group number is: 90630019[b] (2012 Hunan TI Exchange Group). After joining the group, ...; wangxin0901 TI Technology Forum

Should I leave?: Graduation is coming soon, so all kinds of entanglements come with it... By chance, I entered a state-owned enterprise and the CCC certification industry by chance, doing EMC testing. However, I found...; farme Talking about work

Principle of ISO5852 peripheral: [Ask if you don't understand] I've asked this before, but I didn't fully understand it. As shown in the picture, this is an IGBT module driver chip. When designing the desaturation protection, there i...; shaorc Power technology

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components