EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-SLPSC4082

Description
Transponder, SC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerLumentum Operations LLC
Download Datasheet Parametric View All

PH1-SLPSC4082 Overview

Transponder, SC/UPC Connector,

PH1-SLPSC4082 Parametric

Parameter NameAttribute value
MakerLumentum Operations LLC
Reach Compliance Codecompliant
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body height13.2 mm
Body length or diameter84.1 mm
Communication standardsOC-192, SONET
Connection TypeSC/UPC CONNECTOR
Emitter/Detector TypePIN PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1558 nm
Nominal optical power output1.584 mW
minimum return loss-27 dB
Sensitivity-17 dBm
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
Using FPGA to Simulate Taxi Fare Meter
Looking for a program, VHDL...
wanglinacoolmm FPGA/CPLD
GMS87C1102-1202 8-bit microcontroller.pdf
GMS87C1102-1202 8-bit microcontroller is also used to control the microprocessor GMS87C1102-1202...
rain MCU
Please tell me about the power chip in the barley box
224540 The UP10 above has CU3ZL written on the chip (I looked for it on alldatasheetcn.com and ICkey, but couldn't find it). The capacitor next to the 6-pin is 220, and the inductor is 4R7 (it should ...
lidonglei1 Power technology
A spike voltage appears when the current of a single-phase bridge phase-controlled rectifier resistor and inductive load is interrupted
[i=s]This post was last edited by Dahanchong on 2019-4-28 10:04[/i] I am a student, and when I was simulating a single-phase bridge rectifier, I encountered the phenomenon shown in the picture. How do...
大寒虫 Analog electronics
Help: Wireless chip transceiver debugging information
Help: I need information about wireless chip transceiver debugging. I am doing my graduation project, which includes wireless transceiver. I plan to use wireless remote control to implement it. The tr...
fenglin51 Embedded System
Is there a signal after the LINUX system time is changed?
When using alarm() to set a timer, if the system time is changed, there will be a series of problems with recalculating the time. Is there such a signal to notify "the LINUX system time has been chang...
qinxuewei101 Linux and Android

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2757  2701  1460  1946  53  56  55  30  40  2 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号