531BC194M000DG datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Passive components> oscillator> 531BC194M000DG

531BC194M000DG: DescriptionLVDS Output Clock Oscillator, 194MHz Nom, ROHS COMPLIANT, SMD, 6 PIN; CategoryPassive components oscillator; File Size215KB，12 Pages; ManufacturerSilicon Laboratories Inc; Environmental Compliance

Download Datasheet Parametric View All

531BC194M000DG Overview

LVDS Output Clock Oscillator, 194MHz Nom, ROHS COMPLIANT, SMD, 6 PIN

531BC194M000DG Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Maker	Silicon Laboratories Inc
package instruction	ROHS COMPLIANT, SMD, 6 PIN
Reach Compliance Code	unknown
Other features	TRAY
maximum descent time	0.35 ns
Frequency Adjustment - Mechanical	NO
frequency stability	7%
JESD-609 code	e4
Manufacturer's serial number	531
Installation features	SURFACE MOUNT
Nominal operating frequency	194 MHz
Maximum operating temperature	85 °C
Minimum operating temperature	-40 °C
Oscillator type	LVDS
physical size	7.0mm x 5.0mm x 1.85mm
longest rise time	0.35 ns
Maximum supply voltage	3.63 V
Minimum supply voltage	2.97 V
Nominal supply voltage	3.3 V
surface mount	YES
maximum symmetry	55/45 %
Terminal surface	Nickel/Gold (Ni/Au)

Preview

Download Datasheet

View All

S i 5 3 0 / 5 31

EVISION

R Y S TA L

S C I L L A T O R

(XO)

(10 M H

Z T O

1.4 G H

)

Features

Available with any-rate output

frequencies from 10 MHz to 945 MHz

and select frequencies to 1.4 GHz

3rd generation DSPLL

with superior

jitter performance

3x better frequency stability than

SAW-based oscillators

Internal fixed crystal frequency

ensures high reliability and low

aging

Available CMOS, LVPECL,

LVDS, and CML outputs

3.3, 2.5, and 1.8 V supply options

Industry-standard 5 x 7 mm

package and pinout

Pb-free/RoHS-compliant

Si5602

Ordering Information:

See page 7.

Applications

SONET/SDH

Networking

SD/HD video

Test and measurement

Clock and data recovery

FPGA/ASIC clock generation

Pin Assignments:

See page 6.

(Top View)

GND

Description

The Si530/531 XO utilizes Silicon Laboratories’ advanced DSPLL circuitry

to provide a low jitter clock at high frequencies. The Si530/531 is available

with any-rate output frequency from 10 to 945 MHz and select frequencies to

1400 MHz. Unlike a traditional XO, where a different crystal is required for

each output frequency, the Si530/531 uses one fixed crystal to provide a

wide range of output frequencies. This IC based approach allows the crystal

resonator to provide exceptional frequency stability and reliability. In addition,

DSPLL clock synthesis provides superior supply noise rejection, simplifying

the task of generating low jitter clocks in noisy environments typically found in

communication systems. The Si530/531 IC based XO is factory configurable

for a wide variety of user specifications including frequency, supply voltage,

output format, and temperature stability. Specific configurations are factory

programmed at time of shipment, thereby eliminating long lead times

associated with custom oscillators.

CLK–

CLK+

Si530 (LVDS/LVPECL/CML)

GND

Functional Block Diagram

CLK– CLK+

CLK

Si530 (CMOS)

Fixed

Frequency

Any-rate

10–1400 MHz

DSPLL

Clock

Synthesis

GND

CLK–

CLK+

Si531 (LVDS/LVPECL/CML)

GND

Rev. 1.1 6/07

Si530/531

Recommended Resources

JK8 proximity switch circuit

Light control circuit principle circuit diagram

Silicon temperature sensor temperature measurement circuit

Frequency measurement circuit

Accurate 12V battery automatic charger circuit

Video amplifier circuit: TDA6107

EPCS chip programming problem: I want to ask, after programming the EPCS chip through the CONFIG port, if I do not unplug the download line, the FPGA will not start up when I power it on again, nSTATUS will be pulled low, and CONF_...; eeleader-mcu FPGA/CPLD

Questions about multisim simulation: I was recently simulating a 555 oscillator. The square wave I output was input to a voltage follower and then connected to an integrator to get a triangle wave. The problem is as shown in the figure b...; 音速兔 Analog electronics

Help, STM32F103 ADC problem: I use two ADCs for data acquisition. No matter in independent mode or synchronous mode, PA0 (channel 0) will have burr-like signals, and PA1 (channel 1) will have a level of about 1.7V (half of the 3....; laowen_110 stm32/stm8

TLC adopts AC voltage: I want to use TLC2543 to collect the instantaneous value of AC. The frequency of AC signal is only 50HZ. I wonder if the speed can be increased in time?...; 晴歌 Analogue and Mixed Signal

Design of audio products based on DSP: With the acceleration of the digitalization process, digital signals will replace more analog signal environments. Since 2004, the application of DSP in consumer electronics will enter people's lives ...; fish001 Microcontroller MCU

Ask for the classic connection diagram of max196 and 51 single chip microcomputer: Urgent use as title!...; 2002xiao Embedded System

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components