Ortel’s Model 755MM-U is a 1550 nm transmitter suitable for link
lengths of up to 10 km with 79 channel analog loading. The 755MM-U
may also be used up to 20 km with a lower channel load of 11 analog
channels and 40 QAM channels. The 75Ω
RF video input supports
frequencies up to 870 MHz. A 50Ω (75
Ω
available ) RF input supports
frequencies from 950 to 2600 MHz for FTTP, L-Band satellite, and
wireless applications.
Applications
Video signal distribution to
HFC CATV and FTTP nodes
Video overlay in passive
optical networks (PON)
Combines CATV + L Band
inputs into a single platform
Also integrated into the RF/Optical design are Ortel’s low chirp control
and noise suppression circuitry. Ortel’s patented pre distortion
technology provides outstanding performance with any of Ortel’s wide
range of cooled broadband lasers. These modules have optional dual
redundant power supplies and SNMP capability.
The performance specifications indicated below are subject to change.
Performance Highlights
Parameter
Operating Temperature Range
Wavelength (Multiple Options)
Optical Power
Frequency Response
CNR (10 km)
CNR (20 km)
CSO (10 km)
CSO (20 km)
CTB (10 km)
CTB (20 km)
SBS (10 km)
SBS (20 km)
RF Input Return Loss
Optical Return Loss
Min
0
1530
10
47
950
52
48
-
-
-
-
-
-
16
40
Typ
25
-
-
-
-
-
-
-
-
-
-
-
-
-
Max
50
1560
-
870
2600
-
-56
-56
-63
-63
17
12
Unit
°C
nm
dBm
MHz
MHz
dB
dBc
dBc
dBc
dBc
dBm
dBm
dB
dB
Features
Optical Spectrum Reshaping
Technology
Optimized RF integration of
predistorter, amplifiers and
laser
Dual redundant power
supplies
Supports SNMP protocol
Complete, efficient laser bias
and TEC control circuitry
OEM/ODM opportunities
available through Ortel
Wideband Transmitter
Digital monitoring and control
ITU Wavelengths
-
-
See following pages for complete specifications and operating/test conditions.
For more information on this and other products:
Contact Sales at Ortel 626-293-3400, or visit www.emcore.com.
755MM-U 1550 nm Transmitter
DATASHEET- OCT, 2006
Absolute Maximum Ratings
Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are
absolute stress ratings only. Functional operation of the device is not implied at these or any other conditions in
excess of those given in the operational sections of the data sheet. Exposure to absolute maximum ratings for
extended periods can adversely affect device reliability.
Parameter
Operating Temperature Range
Storage Case Temperature Range
RF Input Level
Symbol
T
OP
T
stg
-
Min.
0
-20
-
Max.
50
65
3
Unit
°
C
°
C
dBm
RF Characteristics
Parameter
Bandwidth
Frequency Response
RF Input Level
CNR
3
(10 km)
CNR
5
(20 km)
CSO
2
(10 km)
5
CSO (20 km)
CTB
2
(10 km)
5
CTB (20 km)
Input Impedance
75Ω Video Input Return Loss
75Ω Test Port Input Return Loss
50Ω Input Return Loss
4
1.Excludes tilt component.
2.CW carriers, 79 channel NTSC channel plan, 4 MHz noise bandwidth, -5 dBm received power, SMF-28 or equivalent.
3. CW carriers, 79 channel NTSC channel plan, 4 MHz noise bandwidth, 0 dBm received power, SMF-28 or equivalent
4. 75Ω option available
5. 11 channel NTSC channel plan with 40 channel QAM, 4 MHz noise bandwidth, 0 dBm received power, SMF-28 or equivalent
Condition
-
47-870 MHz
950-2600 MHz
79 channels analog
11 channel analog + 40 QAM
-
-
-
-
-
-
47 – 870 MHz RF Input
950-2600 MHz RF Input
47 to 870 MHz
47 to 870 MHz
950 to 2600 MHz
Min
47
-
-
-2.5
-5.8
52
48
-
-
-
-
-
-
16
16
10
Typ
-
-
-
-2
-5.3
-
-
-
-
-
-
75
4
50
-
-
-
Max
2600
1.5
3.5
1
Unit
MHz
dB
p-p
dB
p-p
dBm
dBm
dB
dB
dBc
dBc
dBc
dBc
Ohms
Ohms
dB
dB
dB
-1.5
-4.8
-
-
-56
-56
-63
-63
-
-
-
-
-
Optical Characteristics
Parameter
Optical Output Power
SBS Threshold
Side Mode Suppression Ratio
Optical Return Loss
1
Condition
-
10 km SMF-28
20 km SMF-28
-
APC style connector
Min
-
-
-
30
40
Typ
10
-
-
-
-
Max
-
17
12
-
-
Unit
dBm
dBm
dBm
dB
dB
1. In order to prevent reflection-induced distortion, the laser must be connected to an optical cable having a return loss of at least 55 dB for discrete
reflections and 30 dB for distributed reflections
2 of 5
755MM-U 1550 nm Transmitter
DATASHEET- OCT, 2006
Power Requirements
Parameter
AC Input Range
DC Input Range
Power
Min.
94
50
36
-
Max.
245
60
60
50
Unit
Vac
Hz
Vdc
W
Package Characteristics
Parameter
Height
Width
Depth
Weight
Dimension
1.75 (44), 1U
19 (483)
17.77(452) with fans
9.0 (4)
Unit
in. (mm.)
in. (mm.)
in. (mm.)
lbs. (kg.)
Part Number / Ordering Information
(Note: customization can be made available upon request)
755MM-U
-
-
-
- XX -
Channel Plan
A = NTSC 80-Ch
L Band Option
50 = 50 ohm
75 = 75 ohm
Options
Connectors
ITU Wavelengths
AC Power Cord
NA = N.AMERICA
UK = U.K. & IRE.
EU = EUROPE
EC = EC NEMA
JP = JAPAN
A = Dual PS + SNMP
SC = SC/APC
ee= 21, 1560.61nm
B = Dual PS, No SNMP
FC = FC/APC
:
C = Single PS, No SNMP EC = E2000/APC ee= 59, 1530.33 nm
3 of 5
755MM-U 1550 nm Transmitter
DATASHEET- OCT, 2006
ITU Wavelength Channel Designations
Channel
21
23
25
27
29
31
33
Wavelength
(nm)
1560.61
1558.98
1557.36
1555.75
1554.13
1552.52
1550.92
Channel
35
37
39
41
43
45
47
Wavelength
(nm)
1549.32
1547.72
1546.12
1544.53
1542.94
1541.35
1539.77
Channel
49
51
53
55
57
59
Wavelength
(nm)
1538.19
1536.61
1535.04
1533.47
1531.90
1530.33
4 of 5
755MM-U 1550 nm Transmitter
DATASHEET- OCT, 2006
Laser Safety Information
This product meets the appropriate standard in Title 21 of the Code of Federal Regulations (CFR). FDA/CDRH
Class IIIb laser product. This device has been classified with the FDA/CDRH under accession number 0220800.
Single-mode bulkhead receptacles with internal SC/APC connectors (standard).
Wavelength = 1.5
μm.
Maximum power = 30 mW.
Product is shipped with internal AC/DC and DC/DC power supply converters.
Caution: Use of controls, adjustments and procedures other than those specified herein may result in
hazardous laser radiation exposure.
Information contained herein is deemed to be reliable and accurate as of issue date. EMCORE reserves the right to change the design or specifications of
the product at any time without notice. EMCORE and the EMCORE logo are trademarks of EMCORE Corporation.
Start erasing according to Zhou Gong's configuration sequence. Because Tiny M0 does not have a reset button, unplug the USB when erasing. Then power on and test the serial port. It can send and receiv...
Q: In ISE4.1, I can only simulate some files compiled with fpga express verilog with modelsimxe, but not post-simulation. I wonder if there is any improvement in 5.1i? Q: In addition to Modelsim, what...
[i=s] This post was last edited by Capacitor on 2018-9-7 15:21 [/i] [align=left][b]What is EMC [/b] [/align] [align=left]EMC is the abbreviation of Electromagnetic Compatibility. In Japanese, it is of...
When developing electronic products with processors, how to improve anti-interference ability and electromagnetic compatibility? 1. The following systems should pay special attention to anti-electroma...
At present, the development of wireless power supply technology for electric vehicles (EVs) is becoming more and more active. In 2012, Volvo of Sweden established Volvo Technology Japan in Tokyo as...[Details]
Traditional broadcasting systems generally need to be operated manually at a fixed time, and can only realize one-way broadcasting with few functions. Traditional bell ringing equipment has a singl...[Details]
When the WDP500-2A plane grating monochromator is used to test the emission wavelength of a high-power laser diode at different currents, the matching of the laser diode has the disadvantages of lo...[Details]
1. Circuit composition
The whole circuit consists of two parts:
1. Power saving control circuit
As shown in the figure below. Including delay circuit and drive circuit.
(1) Delay ci...[Details]
1. Introduction
With the growth of parking demand, the scale of parking lots is becoming larger and larger. A lot of research has been done on intelligent parking lots in China, but most of th...[Details]
Automotive applications are particularly sensitive to EMI events, which are unavoidable in a noisy electrical environment consisting of a central battery, bundled wiring harnesses, various inductiv...[Details]
Converged processors meet scalability requirements
In current embedded system design, solutions based on MCU, DSP, FPGA and ASIC account for more than 90% of the market share. These solutions ...[Details]
Abstract: In order to generate a stable excitation signal, the design of a digital frequency synthesizer is implemented on FPGA using Verilog hardware language. The design includes accumulator, wav...[Details]
In order to highlight the concept of "energy saving and environmental protection" of intelligent buildings, solar street lights are designed for intelligent communities. The inclination and capacit...[Details]
Although it is relatively easy to check the stability of a simple amplifier at lower frequencies, it may be much more difficult to evaluate the stability of a more complex circuit. This artic...[Details]
0 Introduction
With the rise and continuous improvement of the solid-state lighting industry, light-emitting diodes (LEDs) have become an alternative lighting technology and are gr...[Details]
This controller uses PIC16C54 single-chip microcomputer as the controller, and it is very easy to use: just connect a telephone line to the loudspeaker through the controller, and you can rem...[Details]
Problems such as the depletion of natural resources, air pollution, traffic congestion, and rising fossil fuel prices have forced societies and individuals to seek alternative means of transportati...[Details]
Motors, especially those with brushes, generate a lot of noise. This noise must be dealt with if the appliance is to meet the requirements of EMC standards. The means to solve EMC are nothing more ...[Details]
Motors are important products that convert electrical energy into mechanical energy to achieve automation, and they are widely used in industrial control, medical electronics, white a...[Details]
TI Technology Forum
京公网安备 11010802033920号
EEWORLD
