(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperature .......................................................... 65°C to +150°C
Note:
Stresses greater than those listed under MAXIMUM
Ambient Temperature with Power Applied .......................... 40°C to +85°C
RATINGS may cause permanent damage to the
Supply Voltage to Ground Potential (Inputs & Vcc Only) ........ 0.5V to +7.0V device. This is a stress rating only and functional
Supply Voltage to Ground Potential (Outputs & D/O Only) ..... 0.5V to +7.0V operation of the device at these or any other conditions
above those indicated in the operational sections of
DC Input Voltage ................................................................... 0.5V to +7.0V
this specification is not implied. Exposure to absolute
DC Output Current ............................................................................. 120mA maximum rating conditions for extended periods may
Power Dissipation ................................................................................. 0.5W affect reliability.
DC Electrical Characteristics
(Over the Operating Range, T
A
= 40°C to +85°C, V
CC
= 5V ±5%)
Parameters Description
V
IH
V
IL
I
IH
I
IL
I
OZH
V
IK
I
OS
V
H
R
ON
Input HIGH Voltage
Input LOW Voltage
Input HIGH Current
Input LOW Current
High Impedance Output Current
Clamp Diode Voltage
Short Circuit Current
(3)
Input Hysteresis at Control Pins
Switch On Resistance
(4)
V
CC
= Min., V
IN
= 0.0V, I
ON
= 48mA
V
CC
= Min., V
IN
= 2.4V, I
ON
= 15mA
Test Conditions
(1)
Guaranteed Logic HIGH Level
Guaranteed Logic LOW Level
V
CC
= Max., V
IN
= V
CC
V
CC
= Max., V
IN
= GND
0 A, B V
CC
V
CC
= Min., I
IN
= 18mA
A (B) = 0V, B (A) = V
CC
100
150
5
10
7
15
0.7
Min.
2.0
0.5
0.8
±1
±1
±1
1.2
V
mA
m
V
ohm
µA
Typ
(2)
Max.
Units
V
Capacitance
(T
A
= 25°C, f = 1 MHz)
Parameters
(5)
C
IN
C
OFF
C
ON
Description
Input Capacitance
A/B Capacitance, Switch Off
A/B Capacitance, Switch On
Test Conditions
V
IN
= 0V
V
IN
= 0V
V
IN
= 0V
Typ
Max.
6
6
8
Units
pF
Notes:
1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the
applicable device type.
2. Typical values are at V
CC
= 5.0V, T
A
= 25°C ambient and maximum loading.
3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
4. Measured by the voltage drop between A and B pin at indicated current through the switch. ON resistance is determined
by the lower of the voltages on the two (A,B) pins.
5. This parameter is determined by device characterization but is not production tested.
The CC2640 is a wireless MCU for Bluetooth Smart applications. This device belongs to the CC26xx family of cost-effective, ultra-low-power 2.4GHz RF devices. Very low active RF and MCU currents and lo...
[i=s]This post was last edited by paulhyde on 2014-9-15 03:55[/i]c8051f serial communication keyboard lcd DDS control generates square wave triangle wave.........
To be precise, I am a freshman in "eeworld" because I just came here not long ago. I am very happy to see so many experts here and to download so many valuable materials. In this electronics industry,...
I saw the Maxim Startup Program https://bbs.eeworld.com.cn/thread-1061993-1-1.html and applied for it with the idea of giving it a try. Some of the company's new energy projects always have interferen...
The core performance indicators of LED devices are mainly reflected in the following six aspects: 1. Brightness or lumen value; 2. Light decay; 3. Failure rate; 4. Light efficiency; 5. Consistency; 6....
I. Introduction
In the field of power conversion, isolated converters (forward, flyback, and double-ended) with low output DC voltage all use MOSFET as the rectifier device. Since these devi...[Details]
This paper establishes a fuel cell engine test platform based on the NI integrated hardware and software environment. This platform can realize the test and control of fuel cell engines and their a...[Details]
With the rapid development of urban economy, elevators are increasingly used as a vertical transportation tool. However, elevator fault detection and maintenance, especially the role of elevator remot...[Details]
A standard cell
is an electrochemical
cell
used as a voltage reference standard in many electrical standards laboratories
. If properly maintained, standard cells are very stable. The ...[Details]
LED is the abbreviation of light emitting diode, which is an electric light source made of semiconductor technology. The core part of LED is a chip composed of P-type semiconductor and N-type semi...[Details]
12v Lead Acid batteries used in trucks, cars, RVs and uninterruptible power supplies are usually rated at 12V. This circuit monitors the battery, the charge and discharge curves, gives the cu...[Details]
Motors are important products that convert electrical energy into mechanical energy to achieve automation, and they are widely used in industrial control, medical electronics, white a...[Details]
It is well known to automotive suppliers that automakers are demanding more from their supply base. For connector suppliers, this means stricter requirements for product performance, stability and ...[Details]
The era of mobile access to the Internet has arrived, and it will rapidly change the business and infrastructure needs of mobile operators under a whole new trend of requirements. We need 4G LTE to...[Details]
The DisplayPort interface standard is approved by the Video Electronics Standards Association (VESA) to provide an open, scalable standard for the entire industry. The development of DisplayPort ca...[Details]
introduction
Steam turbines are driven by high-temperature and high-pressure steam generated by boilers to run at high speed. They are key power equipment in thermal power plants. The emergenc...[Details]
As the global LED market demand continues to increase, my country's LED industry will face huge opportunities in the future. However, the core LED technology and patents are basically monopolized b...[Details]
Currently, high-frequency and high-efficiency DCDC converters are increasingly used in automotive electronic systems.
High switching frequency can use smaller power inductors and output filter...[Details]
1 Introduction
With the development of computer technology and information technology in the world, the global information age has arrived. All countries are formulating their own development p...[Details]
Current
measurement:
Magnetic balance Hall current
sensor
is used
. The sensor can measure AC from DC to 100kHz.
In automatic measurement and control systems, it is often nec...[Details]