EEWORLDEEWORLDEEWORLD

Part Number

Search

AM28F020-70PIB

Description
2 Megabit (256 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory
File Size260KB,35 Pages
ManufacturerAMD
Websitehttp://www.amd.com
Download Datasheet View All

AM28F020-70PIB Overview

2 Megabit (256 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory

FINAL
Am28F020
2 Megabit (256 K x 8-Bit)
CMOS 12.0 Volt, Bulk Erase Flash Memory
DISTINCTIVE CHARACTERISTICS
s
High performance
— Access times as fast as 70 ns
s
CMOS low power consumption
— 30 mA maximum active current
— 100 µA maximum standby current
— No data retention power consumption
s
Compatible with JEDEC-standard byte-wide
32-pin EPROM pinouts
— 32-pin PDIP
— 32-pin PLCC
— 32-pin TSOP
s
10,000 write/erase cycles minimum
s
Write and erase voltage 12.0 V
±5%
s
Latch-up protected to 100 mA from
–1 V to V
CC
+1 V
s
Flasherase Electrical Bulk Chip Erase
— One second typical chip erase time
s
Flashrite Programming
— 10 µs typical byte program time
— 4 s typical chip program time
s
Command register architecture for
microprocessor/microcontroller compatible
write interface
s
On-chip address and data latches
s
Advanced CMOS flash memory technology
— Low cost single transistor memory cell
s
Automatic write/erase pulse stop timer
GENERAL DESCRIPTION
The Am28F020 is a 2 Megabit Flash memory orga-
nized as 256 Kbytes of 8 bits each. AMD’s Flash mem-
ories offer the most cost-effective and reliable read/
write non-volatile random access memor y. The
Am28F020 is packaged in 32-pin PDIP, PLCC, and
TSOP versions. It is designed to be reprogrammed and
erased in-system or in standard EPROM programmers.
Th e Am 28F 020 i s eras ed w hen s h ip ped from
the factory.
The standard Am28F020 offers access times of as fast
as 70 ns, allowing high speed microprocessors to
operate without wait states. To eliminate bus conten-
tion, the device has separate chip enable (CE#) and
output enable (OE#) controls.
AMD’s Flash memories augment EPROM functionality
with in-circuit electrical erasure and programming. The
Am28F020 uses a command register to manage this
functionality, while maintaining a JEDEC-standard 32-
pin pinout. The command register allows for 100% TTL
level control inputs and fixed power supply levels during
erase and programming, while maintaining maximum
EPROM compatibility.
AMD’s Flash technology reliably stores memory con-
tents even after 10,000 erase and program cycles. The
AMD cell is designed to optimize the erase and pro-
gramming mechanisms. In addition, the combination of
advanced tunnel oxide processing and low internal
electric fields for erase and programming operations
produces reliable cycling. The Am28F020 uses a
12.0±5% V
PP
supply input to perform the Flasherase
and Flashrite functions.
The highest degree of latch-up protection is achieved
with AMD’s proprietary non-epi process. Latch-up pro-
tection is provided for stresses up to 100 mA on
address and data pins from –1 V to V
CC
+1 V.
The Am28F020 is byte programmable using 10 µs
programming pulses in accordance with AMD’s
Flashrite programming algorithm. The typical room
temperature programming time of the Am28F020 is
four seconds. The entire chip is bulk erased using 10
ms erase pulses according to AMD’s Flasherase
algorithm. Typical erasure at room temperature is
accomplished in less than one second. The windowed
package and the 15–20 minutes required for EPROM
erasure using ultraviolet light are eliminated.
Commands are written to the command register using
standard microprocessor write timings. Register con-
tents serve as input to an internal state-machine, which
controls the erase and programming circuitry. During
write cycles, the command register internally latches
Publication#
14727
Rev:
F
Amendment/+2
Issue Date:
January 1998
The pros and cons of interrupting dog feeding!
I have seen many posts on the website that suggest not to feed the dog in the interrupt program. Most people's reason is that the interrupt will not necessarily "die" if the program runs away. But if ...
chenky Embedded System
2011 National Undergraduate Electronic Design Competition Training-Basic Skills
[i=s] This post was last edited by paulhyde on 2014-9-15 03:00 [/i] It contains 2011 National Undergraduate Electronic Design Competition Training - Basic Skills and 2011 National Undergraduate Electr...
谷粒朱古力 Electronics Design Contest
Bit operations that can be used to show off (transferred)
Hacker's Delight The Secret of Efficient Programming and this article from Stanford, it's hard not to show off when using bit operations http://graphics.stanford.edu/~seander/bithacks.htmlBit Twiddlin...
白丁 Integrated technical exchanges
What’s wrong with the TIM4 query program?
#include "iostm8L152k4.h" main() { // First initialize GPIO PD_DDR = 0x08; PD_CR1 = 0x08; // Set PD3 to push-pull output PD_CR2 = 0x00; // Then initialize timer 4 TIM4_IER = 0x00; TIM4_EGR = 0x01; TIM...
suzhiqiang168 stm32/stm8
Does the MSP430 MCU timer have an encoder interface mode?
RT, I saw that the STM32 MCU timer has such a function. I want to ask if the MSP430 MCU timer has an encoder interface mode. Thank you....
rowen800 Microcontroller MCU
Difficult question: Regarding the registry, experts please come in
Operating system password history security baseline requirement: "Maximum password retention period" is set to no more than "90 days". Enter "Control Panel->Administrative Tools->Local Security Policy...
cailong Embedded System

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 759  2407  1599  692  1327  16  49  33  14  27 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号