It is like this, after the metal wire is melted, the high-temperature powder is sprayed onto the surface of the product, but the process time is short, and there is an exhaust system, so the temperatu...
Designers implement current sensing for system protection and monitoring by placing a very small "shunt" resistor in series with the load and a current sense amplifier or op amp between the two. While...
[i=s]This post was last edited by TEL18688947970 on 2021-7-26 11:13[/i]Lingdong Microelectronics is a leading Chinese supplier of general-purpose 32-bit MCU products and solutions. Lingdong Microelect...
The DSP28335 GPIO module is divided into three types of IO ports: PORTA (0-31), PORTB (32-63), and PORTC (64-87). The settings of the GPIO module are mainly completed through three types of registers,...
This is probably the best analog engineer's circuit design guide + a compilation of blog posts on op amp design topicsTo simplify and speed up system design, TI's "Circuit Design Cookbook for Analog E...
[font=微软雅黑][size=4]I am glad to see that there are already 6 pages of replies, which shows that this post has attracted some attention from everyone. No matter in which aspect, my intention has not be...
Hardware designers have begun to adopt FPGA technology in high-performance DSP designs because it can provide 10-100 times faster computing than PC-based or microcontroller-based solutions. Previou...[Details]
1. Introduction
RFID (radio frequency identification) is a non-contact automatic identification technology that emerged in the 1990s. It uses the characteristics of radio frequency signal prop...[Details]
1. Introduction
This design was made for participating in an electronic design competition. It effectively solved the problem of the operation and control of an electric car on a seesaw. The s...[Details]
With the advent of increasingly powerful processors, image sensors, memory, and other semiconductor devices, as well as the algorithms that enable them, computer vision can be implemented in a wide...[Details]
introduction
In the discharge process of tokamak plasma physics, the study of rupture and sawtooth is of great significance. Rupture and sawtooth exist in most tokamaks. Rupture is a notew...[Details]
All electronic design engineers and scientists have performed electrical signal analysis, or signal analysis for short. Through this basic measurement, they can gain insight into signal details and...[Details]
There are three types of mobile TV: one is based on analog TV broadcasting network, another is based on mobile communication network, and the other is based on digital broadcasting network. The f...[Details]
Electronic systems are located at different points on the automotive power bus and therefore often need to operate under very stringent power requirements. These include load dump, cold crank, very lo...[Details]
To differentiate their products in a crowded and competitive market, manufacturers of handheld devices often consider battery life and power management as key selling points for cell phones, PDAs, ...[Details]
July 11, 2012, Beijing - Altera Corporation (NASDAQ: ALTR) today announced the launch of 40-Gbps Ethernet (40GbE) and 100-Gbps Ethernet (100GbE) intellectual property (IP) core products. These core...[Details]
1. Introduction
At present, most lighting equipment still uses traditional energy for lighting. Making full use of solar energy as the energy supply for lighting equipment is of great si...[Details]
Overview:
This paper introduces a method of connecting a CAN-bus network with Ethernet to form a medium-sized remote monitoring/data transmission network.
CAN (Controller Area Network) is ...[Details]
1 Introduction
Intelligent control instruments are one of the most commonly used controllers in industrial control. They are mainly aimed at a specific parameter (such as pressure, tempera...[Details]
1. Introduction
Testing the temperature of steel billets before rolling is an important measure to ensure the quality of steel. Traditional manual testing is difficult to ensure product qu...[Details]
Many battery-powered systems require a visual indicator to show when the battery needs to be replaced. LEDs are commonly used for this purpose, but they consume at least 10mA of current. This con...[Details]
Sensor
京公网安备 11010802033920号
EEWORLD
