The standard shipping format for serial types includes either a lower family group, an upper family group or a grouping of all individual brightness groups
of only a few brightness groups. Individual brightness groups cannot be ordered.
The extrapolated typical minimum and maximum values are calculated with a typical
Φ
V
/I
V
factor of 2.94. It is to consider that the ±3σ range of the
Φ
V
/I
V
factor is 2.8 - 3.1.
Anm.:
Die Standardlieferform von Serientypen beinhaltet entweder eine untere Familiengruppe, eine obere Familiengruppe oder eine Sammelgruppe, die aus
nur wenigen Helligkeitsgruppen bestehen. Einzelne Helligkeitsgruppen sind nicht bestellbar.
Der extrapolierte typische Minimum- und Maximumlichtstrom sind mit einem
Φ
V
/I
V
-Faktor von 2,94 berechnet. Mit der ±3σ-Abweichung ergibt sich ein
"Use a unique formula", "supplement calcium, iron and zinc", "develop intelligence"... These eye-catching words often appear in children's milk advertisements, and many parents buy them for their chil...
I plan to buy a 6472 EVM to do experiments, but I don't know how to operate it. I hope those experienced people can give me some advice. Those TI agents are really not helpful. I called them several t...
SIC1819 Coreless Tachometer/Speedometer Driver SIC1819 is a driver for automotive tachometers (dynamic-magnetic tachometers/speedometers). The chip contains a reference voltage source, a Norton amplif...
0. Preparation First use st-link to connect the stm32 core board and PC for burning St-link Stm32 3.3V 3.3V GND GND SWDIO PART SWCLK DCLK Then connect with USB serial port board to v...[Details]
I have always wanted to write some posts and blogs, but I just couldn't bear to do it as I just graduated. After some preparation, I decided to write down some of the things I learned in the past few...[Details]
LAN8720 configuration: IP: 192.168.192.30 Gateway: 192.168.192.1 A high frequency of ARP packets is detected The content of the packet asks for the mac address of 192.168.192.1, and asks the resp...[Details]
Function List and Notes (lower-level driver part) 1. IO port initialization: control IO and communication IO. Control includes power control, reset and low power mode. Communication is the serial po...[Details]
Time flies. Since the beginning of 2018, news related to home appliance companies have repeatedly made headlines, and competition in the home appliance market continues to intensify. In order to be...[Details]
As the brain of a mobile phone, the mobile phone processing chip is of great importance. Xiaomi, which started out as the MIUI company, has long been keenly aware of the gap between China and devel...[Details]
The independent watchdog of STM32 is driven by a dedicated internal 40Khz low-speed clock, that is, it is still effective even if the main clock fails. Here we need to note that the clock of the inde...[Details]
The pins of stm32 have two uses: GPIO (general purpose io) and AFIO (alternate function io) For some pins (depending on the chip), neither of these two uses exists. For example, in 64-pin products, O...[Details]
I have encountered many problems when tinkering with LD driver recently. I will record them one by one below. Otherwise, who will remember who in five hundred years? 1. Configuration issues of multi-...[Details]
The key is the configuration of registers. The T1 timer (16 bits) of CC2530 needs to configure three registers: T1CTL, T1STAT, IRCON Here is just a brief introduction. For more details, please refer ...[Details]
MCS-51 single-chip microcomputer timer/counter experiment programming program Programming requirements: 1. Connect a light-emitting diode LED to the P1.0 pin, light up for two seconds, turn off for o...[Details]
The circuit shown in the figure requires that the light is off when the machine is turned on. Press the button once, and the light D1 will turn on and automatically turn off after a delay of 10 secon...[Details]
;The hardware connection circuit of the 51 single-chip microcomputer is as follows: ;P1.3 and P1.4 are each connected to a button; ;P0.0 and P0.3 are each connected to a light-emitting diode; ;P2.0~P...[Details]
Requirements: Set timer T1 as an external event counter, count 500 pulses every time, then switch T1 to timing mode and output a positive pulse with a width of 10ms at P1.2. Over and over again. A...[Details]
MCU
京公网安备 11010802033920号
EEWORLD
