I want to find a chip with ASK receiving function, operating frequency of 300-900Mhz, operating voltage of 2.5-5V, and bandwidth less than 25khz. Please give me some advice....
[i=s]This post was last edited by nwx8899 on 2015-12-3 20:30[/i] [backcolor=rgb(239, 245, 249)]The information I have found so far mainly talks about the following two solutions for detecting phase cu...
[align=left][color=rgb(51, 51, 51)]For electronic equipment, a certain amount of heat will be generated when working, which will cause the internal temperature of the equipment to rise rapidly. If the...
The output waveform is shown in the figure above, the circuit schematic is as shown below, the op amp power supply is positive and negative 8V
No matter how you adjust the sliding rheostat, the output...
It is similar to a resistor with a switch, and the measured current signal is in the form of a square wave. How can we measure its fixed equivalent resistance, or how can we calculate it by calculatio...
[font=Tahoma, Helvetica, SimSun, sans-serif]The Flash Download Tools software for ESP8266 has been upgraded again. It supports ESP8266, ESP8285 (ESP8266 with built-in flash), and ESP32. [/font] [img=3...
A single-chip microcomputer is also called a single-chip microcontroller. It is not a chip that completes a certain logical function, but a computer system integrated into one chip. In general, a c...[Details]
Microchip's PIC18F46J50 is a low-power, high-performance 8-bit USB microcontroller (MCU) using nanoWatt XLP technology. The current in deep sleep mode can be as low as 13nA, the operating voltage i...[Details]
introduction
With the continuous optimization of surface mount technology (SMT) and the rapid development of chip component manufacturing technology, the application of chip mounters in the el...[Details]
1. Introduction
Automobile pollution is one of the most important issues that people are most concerned about and need to solve urgently. As an important method for detecting automobile exhau...[Details]
1. Introduction
Since the 1980s, with the continuous development of automotive electronic technology, there are more and more electronic control units in automobiles, such as electronic fuel i...[Details]
All electronic design engineers and scientists have performed electrical signal analysis, or signal analysis for short. Through this basic measurement, they can gain insight into signal details and...[Details]
Two simple circuits are implemented to drive two LEDs from a battery powered microprocessor.
This design is based on a circuit that uses three resistors and a microprocessor I/O pin as an input h...[Details]
5. Identifiers and keywords of C language
A complete PIC microcontroller C language program usually consists of six parts: include files (i.e. header files 1, variable definitions, variable de...[Details]
1. Introduction
At present, most lighting equipment still uses traditional energy for lighting. Making full use of solar energy as the energy supply for lighting equipment is of great si...[Details]
Microcalorimetry
is used to determine energy relationships. Microcalorimetry techniques are often required when performing calorimetric experiments with small sample sizes or slow heating rat...[Details]
1. With the development of modern industry and the continuous improvement of automation, some medium and large control systems have been greatly facilitated, which not only makes control easier, bu...[Details]
Overview:
This paper introduces a method of connecting a CAN-bus network with Ethernet to form a medium-sized remote monitoring/data transmission network.
CAN (Controller Area Network) is ...[Details]
On the afternoon of July 10, Beijing time, Taiwan's largest chip designer MediaTek expects its smartphone chip shipments to grow by double digits in the third quarter of this year, and the company is ...[Details]
The potentiometer is an adjustable electronic component. The main functions of the potentiometer in the circuit are as follows:
1. Used as a voltage divider
A potentiometer is a continuou...[Details]
Many battery-powered systems require a visual indicator to show when the battery needs to be replaced. LEDs are commonly used for this purpose, but they consume at least 10mA of current. This con...[Details]
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
