uPD78F0134M5GC(A1)-8BS datasheet, PDF

Datasheet> All Categories > uPD78F0134M5GC(A1)-8BS

Preview

uPD78F0134M5GC(A1)-8BS: Description8-Bit Single-Chip Microcontrollers; File Size3MB，558 Pages; ManufacturerNEC ( Renesas ); Websitehttps://www2.renesas.cn/zh-cn/

Download Datasheet View All

uPD78F0134M5GC(A1)-8BS Overview

8-Bit Single-Chip Microcontrollers

Preview

Download Datasheet

View All

User’s Manual

78K0/KE1

8-Bit Single-Chip Microcontrollers

PD780131

PD780132

PD780133

PD780134

PD780136

PD780138

PD78F0134

PD78F0138

PD780131(A)

PD780132(A)

PD780133(A)

PD780134(A)

PD780136(A)

PD780138(A)

PD78F0134(A)

PD78F0138(A)

PD780131(A1)

PD780132(A1)

PD780133(A1)

PD780134(A1)

PD780136(A1)

PD780138(A1)

PD78F0134(A1)

PD78F0138(A1)

PD780131(A2)

PD780132(A2)

PD780133(A2)

PD780134(A2)

PD780136(A2)

PD780138(A2)

Document No. U16228EJ2V0UD00 (2nd edition)

Date Published November 2003 N CP(K)

2002

Printed in Japan

NOTES FOR CMOS DEVICES

PRECAUTION AGAINST ESD FOR SEMICONDUCTORS

Note:

Strong electric field, when exposed to a MOS device, can cause destruction of the gate oxide and

ultimately degrade the device operation. Steps must be taken to stop generation of static electricity

as much as possible, and quickly dissipate it once, when it has occurred. Environmental control

must be adequate. When it is dry, humidifier should be used. It is recommended to avoid using

insulators that easily build static electricity. Semiconductor devices must be stored and transported

in an anti-static container, static shielding bag or conductive material. All test and measurement

tools including work bench and floor should be grounded. The operator should be grounded using

wrist strap. Semiconductor devices must not be touched with bare hands. Similar precautions need

to be taken for PW boards with semiconductor devices on it.

HANDLING OF UNUSED INPUT PINS FOR CMOS

Note:

No connection for CMOS device inputs can be cause of malfunction. If no connection is provided

to the input pins, it is possible that an internal input level may be generated due to noise, etc., hence

causing malfunction. CMOS devices behave differently than Bipolar or NMOS devices. Input levels

of CMOS devices must be fixed high or low by using a pull-up or pull-down circuitry. Each unused

pin should be connected to V

or GND with a resistor, if it is considered to have a possibility of

being an output pin. All handling related to the unused pins must be judged device by device and

related specifications governing the devices.

STATUS BEFORE INITIALIZATION OF MOS DEVICES

Note:

Power-on does not necessarily define initial status of MOS device. Production process of MOS

does not define the initial operation status of the device. Immediately after the power source is

turned ON, the devices with reset function have not yet been initialized. Hence, power-on does

not guarantee out-pin levels, I/O settings or contents of registers. Device is not initialized until the

reset signal is received. Reset operation must be executed immediately after power-on for devices

having reset function.

EEPROM is a trademark of NEC Electronics Corporation.

Windows and Windows NT are either registered trademarks or trademarks of Microsoft Corporation in the

United States and/or other countries.

PC/AT is a trademark of International Business Machines Corporation.

HP9000 series 700 and HP-UX are trademarks of Hewlett-Packard Company.

SPARCstation is a trademark of SPARC International, Inc.

Solaris and SunOS are trademarks of Sun Microsystems, Inc.

TRON stands for The Realtime Operating system Nucleus.

ITRON is an abbreviation of Industrial TRON.

User’s Manual U16228EJ2V0UD

These commodities, technology or software, must be exported in accordance

with the export administration regulations of the exporting country.

Diversion contrary to the law of that country is prohibited.

•

The information in this document is current as of May, 2003. The information is subject to change

without notice. For actual design-in, refer to the latest publications of NEC Electronics data sheets or

data books, etc., for the most up-to-date specifications of NEC Electronics products. Not all

products and/or types are available in every country. Please check with an NEC Electronics sales

representative for availability and additional information.

•

No part of this document may be copied or reproduced in any form or by any means without the prior

written consent of NEC Electronics. NEC Electronics assumes no responsibility for any errors that may

appear in this document.

•

NEC Electronics does not assume any liability for infringement of patents, copyrights or other intellectual

property rights of third parties by or arising from the use of NEC Electronics products listed in this document

or any other liability arising from the use of such products. No license, express, implied or otherwise, is

granted under any patents, copyrights or other intellectual property rights of NEC Electronics or others.

•

Descriptions of circuits, software and other related information in this document are provided for illustrative

purposes in semiconductor product operation and application examples. The incorporation of these

circuits, software and information in the design of a customer's equipment shall be done under the full

responsibility of the customer. NEC Electronics assumes no responsibility for any losses incurred by

customers or third parties arising from the use of these circuits, software and information.

•

While NEC Electronics endeavors to enhance the quality, reliability and safety of NEC Electronics products,

customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To

minimize risks of damage to property or injury (including death) to persons arising from defects in NEC

Electronics products, customers must incorporate sufficient safety measures in their design, such as

redundancy, fire-containment and anti-failure features.

•

NEC Electronics products are classified into the following three quality grades: "Standard", "Special" and

"Specific".

The "Specific" quality grade applies only to NEC Electronics products developed based on a customer-

designated "quality assurance program" for a specific application. The recommended applications of an NEC

Electronics product depend on its quality grade, as indicated below. Customers must check the quality grade of

each NEC Electronics product before using it in a particular application.

"Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio

and visual equipment, home electronic appliances, machine tools, personal electronic equipment

and industrial robots.

"Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster

systems, anti-crime systems, safety equipment and medical equipment (not specifically designed

for life support).

"Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life

support systems and medical equipment for life support, etc.

The quality grade of NEC Electronics products is "Standard" unless otherwise expressly specified in NEC

Electronics data sheets or data books, etc. If customers wish to use NEC Electronics products in applications

not intended by NEC Electronics, they must contact an NEC Electronics sales representative in advance to

determine NEC Electronics' willingness to support a given application.

(Note)

(1) "NEC Electronics" as used in this statement means NEC Electronics Corporation and also includes its

majority-owned subsidiaries.

(2) "NEC Electronics products" means any product developed or manufactured by or for NEC Electronics

(as defined above).

M8E 02. 11-1

User’s Manual U16228EJ2V0UD

Recommended Resources

The production of "Walkman" power connector 02

Electronic toys--number circuit

Single tube wireless transmitter circuit diagram

High operating voltage voltage stabilization circuit diagram

Infrared remote control receiver circuit diagram with 60 commands

Multipurpose alarm control circuit for workshops and warehouses

Did you solve Problem F? (Looking forward to the xyt of the experts): [i=s] This post was last edited by paulhyde on 2014-9-15 09:33 [/i] RT, it's a bit broken without the amplifier. . . [[i] This post was last edited by plich on 2009-9-5 10:53 [/i]]...; plich Electronics Design Contest

[Prize Quiz] Xilinx Industrial and Medical Special Topic, Win LX9 Microboard Development Board!: Activity name: [Read the topic and win a big prize] Xilinx Industrial and Medical Topic, win an LX9 Microboard development board worth $89.Event time: July 19-August 19Event format: Read the special t...; EEWORLD社区 FPGA/CPLD

Do you know the eight important knowledge points of FPGA design?: 1. Balance and exchange between area and speed The area here refers to the amount of logic resources consumed by a design in the FPGA/CPLD . For FPGA, it can be measured by the consumed FF (flip-flop)...; XYD李 Talking

How much memory does wince require?: How much memory is needed to run wince on target board? Is 32mb enough? thx...; 圆圈 Embedded System

How should the op amp voltage follower be connected?: I have seen some books introducing how to make an op amp into a voltage follower, with the output connected to the inverting phase, while others only briefly mention the same phase. I would like to as...; liweiliang Analog electronics

Embedded system construction: Embedded system construction[:)][:)][6]...; fighting Embedded System

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components