EEWORLDEEWORLDEEWORLD

Part Number

Search

PPC21270CLF7

Description
RES,SMT,METAL GLAZE,127 OHMS,500WV,.25% +/-TOL,-25,25PPM TC
CategoryPassive components    The resistor   
File Size178KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance  
Download Datasheet Parametric View All

PPC21270CLF7 Overview

RES,SMT,METAL GLAZE,127 OHMS,500WV,.25% +/-TOL,-25,25PPM TC

PPC21270CLF7 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerTT Electronics plc
Reach Compliance Codecompliant
ECCN codeEAR99
structureChip
Manufacturer's serial numberPPC
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package diameter2.67 mm
Package length9.32 mm
Package formSMT
method of packingTR
Rated power dissipation(P)2 W
resistance127 Ω
Resistor typeFIXED RESISTOR
seriesPPC
technologyMETAL GLAZE/THICK FILM
Temperature Coefficient-25,25 ppm/°C
Tolerance0.25%
Operating Voltage500 V
Metal Glaze
Surface Mount
Precision Power Chip
PPC Series
Surge tolerant
Up to 1000 volts
Tight TCR - 25 ppm/°C
Tolerance down to ±0.1%
Solder over nickel
barrier
High
temperature
dielectric
coating
Metal Glaze™ thick
film element fired
at 1000°C to solid
ceramic substrate
Electrical Data
Size
Code
B
D
F
H
Industry
Footprint
1206
2010
2512
3610
IRC
Type
PPC1/8
PPC1/2
PPC1
PPC2
Power
Rating at
70°C (W)
1/8 W
1/2 W
1W
2W 1.33W
Working
Voltage
200
300
350
500
Resistance
Range
(ohms)
100 - 10K
100 - 10K
100 - 10K
100 - 10K
0.1% (B)
0.25% (C)
0.5% (D)
Tolerance
(±%)
Qty /
Reel (7")
2500
1500
N/A
N/A
Qty /
Reel (13")
10000
5000
5000
1500
Environmental Data
Characteristics
Temperature Coefficient
Thermal Shock
Low Temperature Operation
Short Time Overload
High Temperature Exposure
Resistance to Bonding
Exposure
Solderability
Moisture Resistance
Life Test
Terminal Adhesion Strength
Maximum Change
As specified
±0.5% + 0.01 ohm
±0.25% + 0.01 ohm
±0.5% + 0.01 ohm
±0.5% + 0.01 ohm
±0.25% + 0.01 ohm
95% minimum coverage
±0.5% + 0.01 ohm
±0.5% + 0.01 ohm
±1% + 0.01 ohm
±1% + 0.01 ohm
no mechanical damage
Test Method
MIL-R-55342E Par 4.7.9 (-55°C + 125°C)
MIL-R-55342E Par 4.7.3 (-65°C + 150°C, 5 cycles)
MIL-R-55342E Par 4.7.4 (-65°C @ working voltage)
MIL-R-55342E Par 4.7.5 2.5 x
for 5 seconds
MIL-R-55342E Par 4.7.6 (+150°C for 100 hours)
MIL-R-55342E Par 4.7.7 (Reflow soldered to board at 260°C
for 10 seconds)
MIL-STD-202, Method 208 (245°C for 5 seconds)
MIL-R-55342E Par 4.7.8 (10 cycles, total 240 hours)
MIL-R-55342E Par 4.7.10 (2000 hours at 70°C intermittent)
1200 gram push from underside of mounted chip for 60
seconds
Chip mounted in center of 90mm long board, deflected 1mm
so as to exert pull on chip contacts for 5 seconds
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
Wire and Film Technologies Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
PPC Series Issue November 2008 Sheet 1 of 3
Help with NOR partition on wince6!!!
I've been working on NOR partitions recently and have run into some problems. I'd like to ask for advice. The specific situation is this: WINCE6, the board is pxa270, the cloned BSP is mainstonIII, th...
hanzhenwei Embedded System
Application of humidity resistors,
I am asked to design a circuit diagram for the application of a humidity sensitive resistor. It is known that it is connected in series with a 510 ohm resistor and in parallel with a 1M resistor. Ther...
wo160wang Analog electronics
RF Shielding Box Design Technical Data
Product Introduction JC-P505 is a manual shielding box, which can be opened and closed in one action.After opening the cover, the upper cover of the box is supported by two hydraulic support rods, whi...
gongchengshijie RF/Wirelessly
I would like to ask a question about op amp signal amplification
I want to process the DC voltage signal after high voltage division (about 0.1V, the reference point is uncertain, it may be ground or floating high voltage). I want to amplify it with an op amp befor...
myfunny Analog electronics
TI General LED Lighting Seminar
After TI merged with National Semiconductor, it will provide the market with more LED lighting chip products. To this end, TI will hold the 2012 TI General LED Lighting Seminar in Xiamen, Shanghai, Sh...
EEWORLD社区 Analogue and Mixed Signal
Introduction to PCB
Introduction to PCB PCB Basics 1.PCB definition: PCB (Printing Circuit Board) refers to a board that is processed by printing, etching, punching and other means to produce the electrical graphics requ...
wangqingtao Power technology

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1015  1762  1918  2381  2635  21  36  39  48  54 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号