PCINT13 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > PCINT13

Preview

PCINT13: DescriptionHigh Performance, Low Power Atmel AVR 8-bit Microcontroller Advanced RISC Architecture; File Size4MB，294 Pages; ManufacturerAtmel (Microchip)

Download Datasheet View All

PCINT13 Overview

High Performance, Low Power Atmel AVR 8-bit Microcontroller Advanced RISC Architecture

Preview

Download Datasheet

View All

Features

•

High Performance, Low Power Atmel AVR 8-bit Microcontroller

•

Advanced RISC Architecture

– 123 Powerful Instructions - Most Single Clock Cycle Execution

– 32 x 8 General Purpose Working Registers

– Fully Static Operation

•

Non-volatile Program and Data Memories

– 16Kbyte of In-system Programmable (ISP) Program Memory Flash

• Endurance: 10,000 Write/Erase Cycles

– 512Bytes In-system Programmable EEPROM

• Endurance: 100,000 Write/Erase Cycles

– 512Bytes Internal SRAM

– Programming Lock for Self-programming Flash Program and EEPROM Data

Security

– Low Size LIN/UART Software In-system Programmable

•

Peripheral Features

– LF-RFID Reader/Writer Front End

• Carrier Frequency f

OSC

= 100kHz to 150kHz

• Typical Data Rate up to 5Kbaud at 125kHz

• Suitable for Manchester anf Biphase Modulation

• Does not Require an External Crystal

• Power Supply from the Car Battery or from 5V Regulated Voltage

• Optimized for Car Immobilizer Applications

• Tuning Capability

– LIN 2.1 and 1.3 Controller or 8-bit UART

– 8-bit Asynchronous Timer/Counter 0:

• 10-bit Clock Prescaler

• 1 Output Compare or 8-bit PWM Channel

– 16-bit Synchronous Timer/Counter 1:

• 10-bit Clock Prescaler

• External Event Counter

• 2 Output Compares Units or 16-bit PWM Channels each Driving up to 4 Output

Pins

– Master/Slave SPI Serial Interface

– Universal Serial Interface (USI) with Start Condition Detector (Master/Slave SPI,

TWI, ...)

– 10-bit ADC:

• 11 Single-ended Channels

• 8 Differential ADC Channel Pairs with Programmable Gain (8x or 20x)

– On-chip Analog Comparator with Selectable Voltage Reference

– 100µA ±10% Current Source (LIN Node Identification)

– On-chip Temperature Sensor

– Programmable Watchdog Timer with Separate On-chip Oscillator

125kHz LF

Reader/Writer

with Integrated

Atmel AVR

Microcontroller

Atmel ATA5505

Preliminary

9219A–RFID–01/11

Atmel ATA5505 [Preliminary]

1. Description

The Atmel

ATA5505 is an Atmel AVR

microcontroller with LF-RFID reader/writer front end

and LIN interface for low cost network applications.

The Atmel ATA5505 incorporates the energy-transfer circuit for supplying the transponder. It

consists of an on-chip power supply, an oscillator, and a coil driver optimized for automo-

tive-specific distances. It also includes all signal-processing circuits which are necessary to

transform the small input signal into a microcontroller-compatible signal.

The Atmel ATA5505 integrates a low-power CMOS 8-bit microcontroller based on the Atmel

AVR enhanced RISC architecture. By executing powerful instructions in a single clock cycle,

the ATA5505 achieves throughputs approaching 1 MIPS per MHz, allowing the system

designer to optimize power consumption versus processing speed.

The Atmel AVR core combines a rich instruction set with 32 general purpose working regis-

ters. All the 32 registers are directly connected to the Arithmetic Logic Unit (ALU), allowing two

independent registers to be accessed in a single instruction executed in one clock cycle. The

resulting architecture is more code-efficient while achieving throughputs up to ten times faster

than conventional CISC microcontrollers.

The Atmel ATA5505 provides the following features: 16K byte of in-system programmable

Flash, 512bytes EEPROM, 512bytes SRAM, 16 general purpose I/O lines, 32 general purpose

working registers, one 8-bit timer/counter with compare modes, one 8-bit high speed

timer/counter, a universal serial interface, a LIN controller, internal and external interrupts, an

11-channel, 10-bit ADC, a programmable watchdog timer with internal oscillator, and three

software selectable power saving modes. The Idle mode stops the CPU while allowing the

SRAM, timer/counter, ADC, analog comparator, and interrupt system to continue functioning.

Power-down mode saves the register contents, disabling all chip functions until the next inter-

rupt or hardware reset. To minimize switching noise during ADC conversions, ADC noise

reduction mode stops the CPU and all I/O modules except ADC,

The device is manufactured using Atmel’s high-density non-volatile memory technology. The

on-chip ISP Flash allows the program memory to be re-programmed in-system via an SPI

serial interface, by a conventional non-volatile memory programmer or by an on-chip boot

code running on the Atmel AVR core. The boot program can use any interface to download the

application program in the Flash memory. By combining an 8-bit RISC CPU with in-system

self-programmable Flash on a monolithic chip, the Atmel ATA5505 is a powerful microcon-

troller providing a highly flexible and cost-effective solution to many embedded control

applications.

The Atmel ATA5505 AVR is supported with a full suite of program and system development

tools including: C compilers, macro assemblers, program debuggers/simulators, in-circuit

emulators, and evaluation kits.

9219A–RFID–01/11

Recommended Resources

Field output circuit: TDA3654 circuit diagram

NCP1014 drives LED lighting circuit

Crystal diode-capacitor triple boost circuit

DC converter circuit diagram suitable for use in multimeter c

Reed switch liquid level control circuit

555 audio equipment automatic shutdown circuit

【Call for Essays】The Feelings of 51: Haha, what does it mean to hear someone before seeing him? Laugh, what are you laughing at? Hehe, laugh at some people and some things. In fact, 51 can complete all design work. Some people may ask, i...; ddllxxrr 51mcu

How to distinguish between X capacitors and Y capacitors?: At the input end of the AC power supply, three safety capacitors are generally needed to suppress EMI conduction interference. The AC power input is divided into three terminals: live wire (L)/neutral...; 木犯001号 Power technology

Requesting the operation of a function: [i=s]This post was last edited by Hu Doudou's Spring on 2017-5-7 20:54[/i] [size=6]Among them: What is the difference in the result of the operation when (GPIOB, GPIO_Pin_0) is replaced by (GPIOC, GPI...; 胡豆豆的春天 stm32/stm8

Single board design related: Do the signal ground and power ground of a single board have to be separated? The power is mainly the stepper motor or power MOS tube (working in switch mode). What we are doing now is to separate the...; S3S4S5S6 Analog electronics

S7-1200 price?: Does anyone know?...; eeleader Industrial Control Electronics

Project Cooperation---Remote Control System Based on FM Radio: Remote control system based on FM radio//********************************************************Project requirements******************************************************** This project plans to use ...; ykfall Embedded System

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components