LXZ2-3580-Y datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > LED optoelectronic/LED> photoelectric> LXZ2-3580-Y

LXZ2-3580-Y: DescriptionSINGLE COLOR LED; CategoryLED optoelectronic/LED photoelectric; File Size2MB，14 Pages; ManufacturerLumileds; Websitehttps://www.lumileds.com/

Download Datasheet Parametric Compare View All

LXZ2-3580-Y Overview

SINGLE COLOR LED

LXZ2-3580-Y Parametric

Parameter Name	Attribute value
Maker	Lumileds
Reach Compliance Code	compliant
Optoelectronic device types	SINGLE COLOR LED

Preview

Download Datasheet

View All

ILLUMINATION

LUXEON Z

Assembly and Handling Information

Introduction

This application brief addresses the recommended assembly and handling

procedures for LUXEON Z emitters. Proper assembly, handling, and thermal

management, as outlined in this application brief, ensure high optical output and

long lumen maintenance for LUXEON Z emitters.

Scope

The assembly and handling guidelines in this application brief apply to the following

products:

LUXEON Z White (all CCT & CRI)

LUXEON Z Lime (LXZ1-PX01)

LUXEON Z Green (LXZ1-PM01)

LUXEON Z Cyan (LXZ1-PE01)

LUXEON Z Blue (LXZ1-PB01)

LUXEON Z Royal Blue (LXZ1-PR01)

LUXEON Z Deep Red (LXZ1-PA01)

LUXEON Z Red (LXZ1-PD01)

LUXEON Z Red-Orange (LXZ1-PH01)

LUXEON Z Amber (LXZ1-PL01)

In the remainder of this document the term LUXEON Z refers to any product in the

LUXEON Z product family.

Table of Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

1 . Component . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

1.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

1.2 Optical Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

1.3 Handling Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

1.4 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

1.5 Electrical Isolation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

1.6 Mechanical Files. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

1.7 Soldering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

2 . Printed Circuit Board Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

2.1 Footprint and Land Pattern. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

2.2 Surface Finishing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

2.3 Minimum Spacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

3 . Thermal Measurement Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

4 . Assembly Process Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

4.1 Stencil Design. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

4.2 Pick-and-Place . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

4.3 Reflow Accuracy.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

5 . Packaging Considerations – Chemical Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

About Lumileds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Figure 4. Correct handling (top) and incorrect handling (bottom) of LUXEON Z emitters.

When handling finished boards containing LUXEON Z emitters, do not touch the top surface with any fingers (see Figure

5a) or apply any pressure to it. Also, do no turn over the board for probing, if the electrodes are at the back of the board,

or stack multiple boards on top of each other (see Figure 5b). A rough or contaminated surface, which is placed on top of a

LUXEON Z emitter, may damage the silicone overcoat of the emitter. Furthermore, any pressure applied onto the LUXEON

Z emitter during probing may damage the silicone layer or the chip underneath.

1.4 Cleaning

The LUXEON Z emitter should not be exposed to dust and debris. Excessive dust and debris may cause a drastic decrease

in optical output. In the event that the surface of a LUXEON Z emitter requires cleaning, a compressed gas duster at a

distance of 6” away will be sufficient to remove the dust and debris or an air gun with 20 psi (at nozzle) from a distance of

6”. Make sure the parts are secured first.

1.5 Electrical Isolation

The LUXEON Z emitter contains only two electrical pads on the bottom of the ceramic substrate with a spacing of 0.25mm

between them. In order to avoid any electrical shocks and/or damage to the LUXEON Z emitter, each design needs to

comply with the appropriate standards of safety and isolation distances, known as clearance and creepage distances,

respectively (e.g. IEC60950, clause 2.10.4).

1.6 Mechanical Files

Mechanical drawings for LUXEON Z (2D and 3D) are available upon request.

1.7 Soldering

LUXEON Z emitters are designed to be soldered onto a Printed Circuit Board (PCB). For detailed assembly instructions, see

Section 2. substrate as shown in Figure 4.

Figure 5. Do not touch the top of surface of the LUXEON Z emitter when handling a finished board (a) or stack

boards with one or more LUXEON Z emitters on top of each other (b).

LXZ2-3580-Y Related Products

	LXZ2-3580-Y	LXZ1-2780-Y	LXZ1-3080-Y	LXZ1-4080-Y	LXZ2-2780-Y	LXZ2-2790-Y	LXZ2-3080-Y	LXZ2-3090-Y
Description	SINGLE COLOR LED	SINGLE COLOR LED	SINGLE COLOR LED	SINGLE COLOR LED	SINGLE COLOR LED	SINGLE COLOR LED	SINGLE COLOR LED	SINGLE COLOR LED
state	-	-	Active	Active	-	Active	Active	Active
Optoelectronic device type	-	-	SINGLE COLOR LED	SINGLE COLOR LED	-	SINGLE COLOR LED	SINGLE COLOR LED	SINGLE COLOR LED

Recommended Resources

Unbalanced current drying motor winding circuit diagram

Motor automatic reciprocating control circuit

Active subwoofer circuit

CMOS power interface circuit for driving stepper motors

Stable speed circuit

unresolved external symbol ___security_cookie求助: In order to shorten the development cycle, I used windriver9 to write the driver. However, when using winddk to compile the kernel state function, it prompted unresolved external symbol ___security_co...; system110 Embedded System

Notes on DSP architecture from Imperial College London: Notes on DSP architecture from Imperial College London...; 安_然 DSP and ARM Processors

Request an EKC-LM3S8962 development board: I am preparing a project now. Through a single-chip microcomputer or an arm board, I collect the human body's electrocardiogram and other physiological parameters, and then upload them to the server. ...; mybays Buy&Sell

Asking for help when writing tasks in ucosii, the program only runs in the default task: Dear experts, after I wrote a task with ucosii, it only ran in the default task. The program just executed the task once at the beginning. Later, although a very high priority was set, it could not be...; mimosa4188 Real-time operating system RTOS

Free shipping for all items in the last 4 days: TI store special offer: popular development boards as low as 11% off!: From now until November 17 , the TI store Double 11 promotion is still going on.Popular development boards are as low as 11% off and free shipping. You can also participate in the lucky draw by postin...; EEWORLD社区 Wireless Connectivity

Motor Control - TI Motor Drive and Control Solutions Guide 2012: [i=s]This post was last edited by dontium on 2015-1-23 13:01[/i]Motor Control - TI Rotary Motors_Motor Drive and Control Solutions GuideFull version in Chinese and English: TI Rotary Motors_Motor Driv...; 德州仪器 Analogue and Mixed Signal

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components