For applications requiring improved electrical and
thermal performance at reduced cost, consider
DATEL’s new UCQ series “quarter brick” DC/DC
power converters. These compact units measure
just 1.45" x 2.3" x 0.4" (36.8 x 60.9 x 10.2 mm)
and fit the industry-standard footprint.
Available outputs range between 1.2V @ 30 Amps
to 15V @ 6.7 Amps and accept a wide input range.
The UCQ’s interleaved, synchronous-rectifier
topology offers high efficiency (up to 93%), tight
line and load regulation, low noise and fast step
response. A single-board optimized open-frame
design contributes to impressive thermal opera-
tion. UCQ’s will operate up to +70°C and 100 LFM
airflow with no derating.
The UCQ’s feature full isolation to 2250Vdc
meeting BASIC insulation requirements of
UL/EN/IEC 60950-1. Input filters reduce propa-
gated switching noise back to input sources. Also
included is a remote On/Off switch control (with
positive or negative polarity), output trim adjustable
over nominal and output sense functions to reduce
power lead losses. Extensive protection items
avoid damage from out of limit voltages, currents
and temperatures. Protection faults automatically
recover using the hiccup technique. Besides safety
testing to 60950-1, certifications for the UCQ in-
clude application for EMC compliance (to EN55022/
CISPR22 with filter), qualification testing.
+SENSE
(7)
+V
OUT
(8)
+V
IN
(3)
SWITCH
CONTROL
–V
OUT
(4)
–V
IN
(1)
–SENSE
(5)
PWM
CONTROLLER
OPTO
ISOLATION
REFERENCE &
ERROR AMP
V
OUT
TRIM
(6)
INPUT UNDERVOLTAGE, INPUT
OVERVOLTAGE, AND OUTPUT
OVERVOLTAGE COMPARATORS
REMOTE
ON/OFF
CONTROL*
(2)
* Can be ordered with positive (standard) or negative (optional) polarity.
Figure 1. Simplified Schematic
For full details go to
www.murata-ps.com/rohs
Typical topology may vary between units.
www.murata-ps.com/support
MDC_UCQ Models.B20
Page 1 of 24
Single Output UCQ Models
Low-Profile, Quarter Brick, 8.3-40 Amp
Isolated DC/DC Converters
PERFORMANCE SPECIFICATIONS SUMMARY AND ORDERING GUIDE
➀
Output
R/N (mVp-p)
Root Models
➀
UCQ-1.2/40-D24P-C
UCQ-1.2/30-D48N-C
UCQ-1.5/25-D48N-C
UCQ-1.5/40-D48N-C
UCQ-1.8/30-D48N-C
UCQ-1.8/40-D48N-C
UCQ-2.5/40-D24P-C
UCQ-2.5/30-D48N-C
UCQ-3.3/35-D24P-C
UCQ-3.3/20-D48N-C
UCQ-3.3/30-D48N-C
UCQ-3.3/40-D48N-C
UCQ-5/20-D24P-C
UCQ-5/20-D48N-C
UCQ-5/25-D48N-C
UCQ-12/8.3-D48N-C
UCQ-15/6.7-D48N-C
V
OUT
I
OUT
Power
(Volts) (Amps) (Watts)
Typ.
Max.
Regulation (Max.)
➁
Line
Load
V
IN
Nom.
(Volts)
Range
(Volts)
I
IN
no
load (mA)
Input
I
IN
full
load
(Amps)
Efficiency
Min.
Typ.
1.2
1.2
1.5
1.5
1.8
1.8
2.5
2.5
3.3
3.3
3.3
3.3
5
5
5
12
15
40
30
25
40
30
40
40
30
35
20
30
40
20
20
25
8.3
6.7
48
36
37.5
60
54
72
100
75
115.5
66
99
132
100
100
125
99.6
100.5
50
50
50
80
50
80
50
80
50
50
60
50
35
50
100
100
100
80
100
100
100
120
100
120
80
80
100
60
55
100
150
150
Please contact Murata Power Solutions for further information.
±0.125%
±0.25%
48
36-75
30
0.90
±0.125%
±0.25%
48
36-75
50
0.94
±0.125%
±0.25%
48
36-75
50
1.45
±0.125%
±0.25%
48
36-75
45
1.31
±0.1%
±0.2%
48
36-75
30
1.70
±0.125%
±0.25%
24
18-36
120
4.96
±0.125%
±0.25%
48
36-75
50
1.80
±0.25%
±0.25%
24
18-36
130
5.41
±0.125%
±0.25%
48
36-75
50
1.53
±0.125%
±0.25%
48
36-75
50
2.3
±0.1%
±0.2%
48
36-75
30
3.06
±0.125%
±0.25%
24
18-36
160
4.55
±0.125%
±0.25%
48
36-75
80
2.26
±0.125%
±0.25%
48
36-75
30
2.89
±0.125%
±0.25%
48
36-75
80
2.28
±0.125%
±0.25%
48
36-75
100
2.28
81%
81%
85%
83%
86%
82%
85%
87%
88.5%
89.5%
89%
88%
89%
88%
90%
90%
83%
83%
86%
86%
88%
84%
87%
89%
90%
91%
90%
91.5%
92%
90%
91%
92%
➀
Please refer to the part number structure for additional ordering part numbers and options.
➁
All specifications are at nominal line voltage and full load, +25 deg.C unless otherwise noted. See detailed specifications. Output capacitors are 1 μF ceramic || 10 μF electrolytic. I/O caps are necessary for
our test equipment and may not be needed for your application.
Outline dimensions:
2.3 × 1.45 × 0.40 inches
58.4 × 36.8 × 10.2 mm
Pinout: P32
(all models)
PART NUMBER STRUCTURE
Output
Configuration:
Unipolar,
single output
U CQ
-
3.3
/
30
-
D48 N B
H Lx
-
C
RoHS Hazardous Materials compliance
C
= RoHS-6, standard (does not claim EU RoHS exemption 7B–lead in solder)
Y
= RoHS-5 (with lead), optional, special order
Pin length option
Blank
= standard pin length 0.180 in. (4.6 mm)
L1
= 0.110 in. (2.79 mm)*
L2
= 0.145 in. (3.68 mm)*
Conformal coating
(optional)
Blank
= no coating, standard
H
= coating added, optional special order
Baseplate
(optional)
Blank
=
No baseplate
, standard
B
=
Baseplate installed
, optional special order
On/Off Control Polarity
P
=
Positive polarity (standard for D24, optional for D48)
N
=
Negative polarity (standard for D48, optional for D24)
[i=s]This post was last edited by paulhyde on 2014-9-15 09:48[/i]2010 Shandong Province Electronic Design Competition (Control Category) Exchange Group 71477207
Everyone is welcome to join......
How do the interrupt registers and interrupt controllers work with each other? What is the difference between the timer interrupt and the P1,2 interrupt?...
I am a newcomer here, learning new knowledge and making new friends.
I think this place is really great. Every day there are many people discussing issues and expressing their opinions here.
Seeing th...
Table of contentsRaspberry Pi Windows IoT Development (Part 1)
Raspberry Pi Windows IoT Development (Part 2) USB Camera
Raspberry Pi Windows IoT Development (Part 3) Flashing LED
Raspberry Pi Windows ...
1. Introduction
RFID (radio frequency identification) is a non-contact automatic identification technology that emerged in the 1990s. It uses the characteristics of radio frequency signal prop...[Details]
Microchip's PIC18F46J50 is a low-power, high-performance 8-bit USB microcontroller (MCU) using nanoWatt XLP technology. The current in deep sleep mode can be as low as 13nA, the operating voltage i...[Details]
Do you often have to add brake fluid to your car's brakes? The fact that you need to pump out the brake fluid to make sure there is no gas in the brake fluid line may not be done by the car owner h...[Details]
1 Introduction
With the acceleration of the pace of urban modernization, society has higher requirements for urban road lighting and urban lighting projects. The state has clearly required tha...[Details]
For a long time, due to the limitation of hardware conditions, the display devices of traditional small handheld devices such as PDA are usually monochrome LCD, and the user interface is very simpl...[Details]
Two simple circuits are implemented to drive two LEDs from a battery powered microprocessor.
This design is based on a circuit that uses three resistors and a microprocessor I/O pin as an input h...[Details]
Electronic systems are located at different points on the automotive power bus and therefore often need to operate under very stringent power requirements. These include load dump, cold crank, very lo...[Details]
This paper establishes a fuel cell engine test platform based on the NI integrated hardware and software environment. This platform can realize the test and control of fuel cell engines and their a...[Details]
In the previous series, we have listed some basic knowledge of C language in Tables 1 to 3. We hope that beginners can strengthen their memory of the above tables and gradually learn to use them wh...[Details]
Microcalorimetry
is used to determine energy relationships. Microcalorimetry techniques are often required when performing calorimetric experiments with small sample sizes or slow heating rat...[Details]
1. Introduction
Testing the temperature of steel billets before rolling is an important measure to ensure the quality of steel. Traditional manual testing is difficult to ensure product qu...[Details]
This week, Microsoft held its 2012 Microsoft Worldwide Partner Conference (WPC) in Toronto, Canada. At the conference, Microsoft showed its new products and services to partners around the world. A...[Details]
Continuity test
A variety of devices need to be checked for continuity, including cable assemblies, printed circuit boards, and connectors to ensure that these components have the expected contin...[Details]
1 Embedded Systems
Embedded System refers to a collection of computer hardware and software with specific functions or purposes, which is divided into embedded software system and embe...[Details]
Abstract: In order to realize wireless automatic alarm and monitoring of major safety places, based on the basic principle of pyroelectric infrared sensing, a detector for receiving infrared radia...[Details]
Electronics Design Contest
京公网安备 11010802033920号
EEWORLD
