EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-GLPFA3161

Description
Transponder, 10000Mbps(Tx), 10000Mbps(Rx), FC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerJDS Uniphase Corporation ( VIAVI )
Websitehttp://www.jdsu.com/index.html
Download Datasheet Parametric View All

PH1-GLPFA3161 Overview

Transponder, 10000Mbps(Tx), 10000Mbps(Rx), FC/UPC Connector,

PH1-GLPFA3161 Parametric

Parameter NameAttribute value
MakerJDS Uniphase Corporation ( VIAVI )
Reach Compliance Codecompliant
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body width56.1 mm
body height13.2 mm
Body length or diameter76.5 mm
Connection TypeFC/UPC CONNECTOR
Data rate (receive)10000 Mbps
Data rate (send)10000 Mbps
Emitter/Detector TypePIN PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1540 nm
Nominal optical power output1.584 mW
minimum return loss-27 dB
Sensitivity-17 dBm
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
Download the full set of ultra-stable Protel99se plus automatic Chinese package
Download the full set of ultra-stable Protel99se plus automatic Chinese package http://www.vip998.com/Soft/ShowSoftDown.asp?UrlID=1SoftID=50Download the full set of the ultra-stable Protel99se plus au...
fighting Analog electronics
Written for Symbian OS development beginners
1. No one forced you, you chose Symbian OS voluntarily. 2. This is the most important question, is there a future for developing software for Symbian OS? Every Symbian OS developer is considering this...
程序天使 Embedded System
Ask the moderator PowerAnts
I read one of your posts about 34063, which said that the efficiency can reach 97%. I admire it very much. Now I have also drawn a diagram of 34063. Please give me some guidance. If the input is 5V/2A...
fjzhang10 Power technology
Help - Program for sending and receiving short distances between two computers in serial communication mode
I. Requirements and content requirements for graduation thesis: 1. Master the basic principles of serial communication. 2. Master the basic structure and characteristics of RS-232. 3. Master the worki...
jb2680 Embedded System
ATMEL9261 serial debugging bootloader problem under pb5.0
Hello everyone! I am debugging the bootloader of 9261 under pb5.0 recently. Since there is no Ethernet on my board, I have to choose to use the serial port to download and debug. I have set Target->co...
wuh2003 Embedded System
CC1101 sending data problem
Recently, I was debugging CC1101 for link lighting control of LED lights. I encountered some problems during debugging. I am posting this thread for help. CC1101 is used for sending, and PT4303 is use...
76159437 Wireless Connectivity

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 885  217  2922  88  665  18  5  59  2  14 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号