stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
PERSONAL INJURY
•
The WDRR must be installed in accordance with the
requirements specified in this document in order to comply
with the specific Country Communication Agency
requirements. (i.e. FCC, IC, ETSI, ACMA, etc.) See
Section 3 as it requires choosing the correct Country Use
Code and thus allowable antenna and/or cable usage.
WARNING
WARNING
Honeywell does not recommend using devices for critical
control applications where there is, or may be, a single point
of failure or where single points of failure may result in an
unsafe condition. It is up to the end-user to weigh the risks
and benefits to determine if the products are appropriate for
the application based on security, safety and performance.
Additionally, it is up to the end-user to ensure that the
control strategy results in a safe operating condition if any
crucial segment of the control solution fails.
Honeywell customers assume full responsibility for learning
and meeting the required Declaration of Conformity,
Regulations, Guidelines, etc. for each country in their
distribution market.
Failure to comply with these instructions could result in
death or serious injury.
•
Pay attention to ESD discharge at dc-in port.
WARNING
WARNING
•
Korean Communication Commission does not allow this
equipment to be used for rescue service.
•
Anatel states that this device works as a secondary
function model. It may not be used as a protection device
against harmful interference. It cannot cause interference
with systems that are running as primary function.
WARNING
CAUTION
* Power to the WDRR should not be applied during
installation of antenna as damage could occur to the
WDRR electronics.
WARNING
•
To satisfy FCC RF exposure requirements for mobile
transmitting devices, a separation distance of 20 cm or
more should be maintained between the antenna of this
device and persons during device operation To ensure
compliance, operation at closer than this distance is not
recommended. The antenna used for this transmission
must not be co-located in conjunction with any other
antenna or transmitter.
Failure to comply with these instructions could result in
death or serious injury.
RF EXPOSURE
CAUTION
* The WDRR receiver offers optimal performance when
paired with Limitless™ inputs that have a firmware
version of 7170 or a greater number (i.e., FW7170 will be
printed on the Limitless™ input label). If the Limitless™
input is paired with older firmware (FW7170 or a lesser
number), the WDRR may exhibit delayed responses
under simultaneous operation.
Sensing and Productivity Solutions
Limitless™
WDRR Receiver
T
ABLE OF
C
ONTENTS
Issue 5
50063987
TABLE OF CONTENTS
............................................................................................................................................................ II
LIST OF FIGURES
.................................................................................................................................................................... VI
I want to make a point-and-read device. There seem to be several chipsets from several manufacturers to choose from. Can anyone provide a chipset for development (or where can I find an agent to buy o...
In the circuit using PIC16F716, a 20MHz crystal oscillator is used. As a result, the crystal oscillator sometimes oscillates and sometimes does not oscillate. In addition, the period and waveform of t...
LM3S8962, ASM problem. Why can the following code run normally: OSIntCtxSw PUSH {R4, R5} LDR R4, =NVIC_INT_CTRL ; trigger the PendSV exception LDR R5, =NVIC_PENDSVSET STR R5, [R4] POP {R4, R5} BX LR N...
[img]http://hiphotos.baidu.com/mtbf2000/pic/item/7efbff3f9f4c47fa55e72337.jpg[/img]Insulation resistance: The insulation between the windings and the core of an ideal transformer is an insulation requ...
Studio 764 was established in 2010 and is affiliated to the School of Software, Jiangxi Agricultural University.The studio members are composed of undergraduates. The purpose of establishing the studi...
As cellular phones become more advanced, the power consumption of the system during operation and the power consumption during standby are also increasing. Therefore, the power management design of...[Details]
To differentiate their products in a crowded and competitive market, manufacturers of handheld devices often consider battery life and power management as key selling points for cell phones, PDAs, ...[Details]
July 11, 2012, Beijing - Altera Corporation (NASDAQ: ALTR) today announced the launch of 40-Gbps Ethernet (40GbE) and 100-Gbps Ethernet (100GbE) intellectual property (IP) core products. These core...[Details]
In the single-chip microcomputer system, in addition to display devices, sound devices are often used, and the most common sound device is the buzzer. Buzzers are generally used for some low-demand...[Details]
Only a small number of LED manufacturers can produce high-quality LEDs. For applications that are only used for simple indication, low-quality LEDs are sufficient. However, high-quality LEDs must...[Details]
The serial interface real-time clock chip DS1302 launched by Dallas Company in the United States can trickle charge the backup battery of the clock chip. Due to the main features of the chip such a...[Details]
1. Introduction
With the increasing popularity of fully automatic washing machines, consumers have higher and higher requirements for their environmenta...[Details]
Fruit planting is an important part of China's agricultural development, and fruit tree pest control operations are becoming more and more important. At present, the overall level of pesticide applica...[Details]
Currently, the commonly used solar cell technologies include monocrystalline silicon solar cells and polycrystalline silicon thin-film solar cells. Production process: Monocrystalline silicon solar...[Details]
The future energy storage hotspot is not coal or iron ore, but lithium. This lightest metal in nature may be the heaviest resource in the future energy landscape. China launched an ambitious electr...[Details]
At present, with the diversification of portable products and the almost harsh requirements for audio and video parts, the power consumption requirements of the whole machine have been raised to a ...[Details]
It should be understood as follows: DC-DC means direct current to direct current (conversion of different DC power values). Anything that meets this definition can be called a DC-DC converter, incl...[Details]
Features
POE technology can ensure the safety of existing structured cabling while ensuring the normal operation of the existing network and minimizing costs. The IEEE 802.3af standard is ...[Details]
With the popularity of digital appliances, rechargeable batteries can be seen everywhere in people's daily lives and have become one of the indispensable daily necessities.
This article gives ...[Details]
0 Introduction
PROFIBUS is an open digital communication system with a wide range of applications, which has been included in the international standards IEC 61158 and IEC 61784. Since the gen...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
