CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTE:
2.
θ
JA
is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See
Tech Brief TB379.
Electrical Specifications
All specifications apply under the following conditions unless otherwise noted: AVDD = 1.8V, OVDD = 1.8V,
T
A
= -40°C to +85°C (typical specifications at +25°C), A
IN
= -1dBFS, f
SAMPLE
= Maximum Conversion Rate
(per speed grade).
KAD5612P-25
(Note 3)
PARAMETER
DC SPECIFICATIONS
Analog Input
Full-Scale Analog
Input Range
Input Resistance
Input Capacitance
Full Scale Range
Temp. Drift
Input Offset Voltage
Gain Error
Common-Mode
Output Voltage
Clock Inputs
Inputs Common
Mode Voltage
CLKP,CLKN Input
Swing
Power Requirements
1.8V Analog Supply
Voltage
1.8V Digital Supply
Voltage
1.8V Analog Supply
Current
1.8V Digital Supply
Current (Note 4)
Power Supply
Rejection Ratio
AVDD
OVDD
I
AVDD
I
OVDD
PSRR
3mA LVDS
30MHz, 200mV
P-P
signal on AVDD
1.7
1.7
1.8
1.8
170
68
-36
1.9
1.9
177
76
1.7
1.7
1.8
1.8
158
66
-36
1.9
1.9
165
74
1.7
1.7
1.8
1.8
142
64
-36
1.9
1.9
152
72
1.7
1.7
1.8
1.8
128
62
-36
1.9
1.9
135
70
V
V
mA
mA
dB
0.9
1.8
0.9
1.8
0.9
1.8
0.9
1.8
V
V
V
FS
R
IN
C
IN
A
VTC
V
OS
E
G
V
CM
435
Differential
Differential
Differential
Full Temp
-10
1.40
1.47
1000
1.8
90
±2
±2
535
635
435
10
-10
1.54 1.40
1.47
1000
1.8
90
±2
±2
535
635
435
10
-10
1.54 1.40
1.47
1000
1.8
90
±2
±2
535
635
435
10
-10
1.54 1.40
1.47
1000
1.8
90
±2
±2
535
635
10
1.54
V
P-P
Ω
pF
ppm/°C
mV
%
mV
SYMBOL
CONDITIONS
MIN
TYP
KAD5612P-21
(Note 3)
TYP
KAD5612P-17
(Note 3)
TYP
KAD5612P-12
(Note 3)
TYP
MAX UNITS
MAX MIN
MAX MIN
MAX MIN
Total Power Dissipation
Normal Mode
P
D
3mA LVDS
429
456
405
432
372
405
342
369
mW
4
FN6803.2
September 9, 2009
KAD5612P
Electrical Specifications
All specifications apply under the following conditions unless otherwise noted: AVDD = 1.8V, OVDD = 1.8V,
T
A
= -40°C to +85°C (typical specifications at +25°C), A
Recently, I have been investigating the processor for the next product. At first, I planned to use 6410, but its BGA pitch is 0.5mm. If the quantity is not large, the cost will be very high. Later, I ...
Before answering this question, I would like to ask you to answer a question of mine: Can one controller control two LIN transceivers, that is, can it control two LIN nodes?If so, I have a strange que...
Firstly, the advantages of high-frequency link inverter technology in inverter power supply are briefly introduced. Then, the main circuit and control scheme of 1000VA high-frequency link inverter pow...
[i=s]This post was last edited by mastone1981 on 2014-5-31 00:23[/i] I just want to control the motor, as long as the motor turns and stops, it doesn't need to rotate. The motor's working voltage is 3...
Traditional broadcasting systems generally need to be operated manually at a fixed time, and can only realize one-way broadcasting with few functions. Traditional bell ringing equipment has a singl...[Details]
This program is written to simulate the serial port hardware mechanism. When used, a timed interrupt can be set with a time interval of 1/4 baud rate. The receiving function is called once for ea...[Details]
1. Circuit composition
The whole circuit consists of two parts:
1. Power saving control circuit
As shown in the figure below. Including delay circuit and drive circuit.
(1) Delay ci...[Details]
Google's driverless technology is not only an eye-catching technology, but also a subversion of the car usage model.
Those who have watched anti-terrorism films and TV dramas must have been im...[Details]
1. Introduction
With the growth of parking demand, the scale of parking lots is becoming larger and larger. A lot of research has been done on intelligent parking lots in China, but most of th...[Details]
Converged processors meet scalability requirements
In current embedded system design, solutions based on MCU, DSP, FPGA and ASIC account for more than 90% of the market share. These solutions ...[Details]
DSP (digital signal processor) is used more and more frequently in today's engineering applications. There are three main reasons for this: first, it has powerful computing power and is capable of ...[Details]
Overview
As a remote network communication control method with advanced technology, high reliability, complete functions and reasonable cost, CAN-bus has been widely used in various automa...[Details]
Only a small number of LED manufacturers can produce high-quality LEDs. For applications that are only used for simple indication, low-quality LEDs are sufficient. However, high-quality LEDs must...[Details]
1. Introduction
With the increasing popularity of fully automatic washing machines, consumers have higher and higher requirements for their environmenta...[Details]
1 Embedded Systems
Embedded System refers to a collection of computer hardware and software with specific functions or purposes, which is divided into embedded software system and embe...[Details]
This article discusses the six design steps of LED lighting system design in detail: (1) determine the lighting requirements; (2) determine the design goals and estimate the optics; (3) the efficie...[Details]
Currently, the commonly used solar cell technologies include monocrystalline silicon solar cells and polycrystalline silicon thin-film solar cells. Production process: Monocrystalline silicon solar...[Details]
The production process of lithium batteries does not mention the previous processes such as material preparation, winding, liquid injection, and packaging, but only talks about the final formation ...[Details]
The principles to be followed are as follows:
(1) In terms of component layout, related components should be placed as close as possible. For example, clock generators, crystal oscillat...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
