EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-SLASC352N

Description
Transponder, SC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerJDS Uniphase Corporation ( VIAVI )
Websitehttp://www.jdsu.com/index.html
Download Datasheet Parametric View All

PH1-SLASC352N Overview

Transponder, SC/UPC Connector,

PH1-SLASC352N Parametric

Parameter NameAttribute value
MakerJDS Uniphase Corporation ( VIAVI )
Reach Compliance Codeunknown
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body height13.2 mm
Body length or diameter84.1 mm
Communication standardsOC-192, SONET
Connection TypeSC/UPC CONNECTOR
Emitter/Detector TypeAVALANCHE PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1547 nm
Nominal optical power output1.584 mW
minimum return loss-27 dB
Sensitivity-24 dBm
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
MSP430 communicates with mobile phone through headphone interface. Step 1: Understanding headphone interface
[align=left][size=4]Let's take a look at the definition of the headphone jack on the mobile phone and see if it can complete the function of hardware peripherals communicating with the mobile phone. T...
wstt Microcontroller MCU
How does 430 drive 74 series chips?
430 is powered by 3V while 74 series is powered by 5V. How to drive it? It is impossible to convert all signals?...
sunway73 Microcontroller MCU
Request circuit diagram
I am working on a gas detection project. I used to design it in Verilog HDL language, but now I am at a loss. Please give me some guidance and provide me with some gas sensor detection circuits. Thank...
learndkid Embedded System
DC LED soft light strip short circuit detection
[color=#333333][font=微软雅黑]Hello everyone: [/font][/color][font=微软雅黑][color=#333333] [/color][/font][color=#333333][font=微软雅黑] LED soft light strip products, DC 24V power supply, maximum working curren...
wzk198005 LED Zone
Can't two SPIs of msp430f5229 be used at the same time?
Below is my configuration initialization code for clock configuration and two SPI //Debug clock configuration void halInitMCU(void) { WDTCTL = WDTPW + WDTHOLD; // Stop watchdog timer // P5SEL |= BIT2+...
wangfeng Microcontroller MCU
How to display on nokia5110LCD based on msp430 and digital blood oxygen module sensor
How can I display the blood oxygen sensor on the Nokia 5110 LCD based on the msp430 and digital blood oxygen module? Thank you!...
zhao_金辉 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 911  2296  1734  2505  236  19  47  35  51  5 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号