*** Resistance value measured with ≤10 % rated current at 25 °C ambient. Tolerance ±30 %.
**** 20 A – 60 A: Melting I
2
t calculated at 10 times rated current. 80 A – 100 A: Melting I
2
t calculated at 6 times rated current.
No.
1
2
Test
Solderability
Resistance to
soldering heat
Temperature setup: 235 ±5 °C
Time setup: 30 sec.
Test Condition
Temperature setup: 235 +0 / -5 °C
Time setup: 10 sec.
Requirement
After test terminal electrode wetting
area must be greater than 95 %
DCR change ≤ ±15 %
DCR change ≤ ±15 %
No mechanical damage
Test Reference
IEC 68-2-58
IEC 68-2-58
MIL-STD-202G
Method 107G
Test Condition B
MIL-STD-202G
Method 103B
Test Condition A
MIL-STD-202G
Method 101E
Test Condition A
IEC 60127-4
MIL-STD-202G
Method 201A
3
Thermal shock
Temperature setup:
25 °C ~ -65 °C ~ 25 °C ~ 125 °C
Time setup: -65 °C (30 min)
~ 25 °C (5 min) ~ 125 °C (30 min)
~ 25 °C (5 min), 5 cycles
Heat (85 ±0.5 °C)
High Humidity (85 ±1 % RH)
240 hours
Salt spray concentration: 5 ±1 %
Test liquid temperature: 35 ±0.5 °C
96 hours
The board shall be bent by 1 mm
at a rate of 1 mm/sec.
Frequency setup: 10 ~ 55 ~ 10 Hz
Time setup: 1 Minute/cycle
(X-Y-Z, 120 cycles, 6 hours)
4
5
6
7
Humidity unload
Salt spray
Bending
Vibration
DCR change ≤ ±15 %
No mechanical damage
DCR change ≤ ±15 %
No mechanical damage
DCR change ≤ ±15 %
DCR change ≤ ±15 %
No mechanical damage
WARNING Cancer and Reproductive Harm -
www.P65Warnings.ca.gov
* RoHS Directive 2002/95/EC Jan. 27, 2003 including annex and RoHS Recast 2011/65/EU June 8, 2011.
** Bourns considers a product to be “halogen free” if (a) the Bromine (Br) content is 900 ppm or less; (b) the Chlorine (Cl) content is 900 ppm or less; and (c) the total Bromine (Br) and
Chlorine (Cl) content is 1500 ppm or less.
“SinglFuse” is a trademark of Bourns, Inc.
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
SinglFuse
™
SF-2923UC-C Series Applications
n
Li-ion Battery Packs
n
Energy Storage Systems (ESS)
n
Power Tools
n
Electric Assist Bicycles
n
Servers and Routers
n
Uninterruptible Power Supplies (UPS)
n
Power Distribution Units (PDUs)
n
Power Factor Correction (PFC)
SF-2923UC-C Series – Ultra-High Current SMD Fuses
Environmental Characteristics
Operating Temperature................................................................................................................................................................ -55 °C to +125 °C
Storage Conditions
Temperature ............................................................................................................................................................................ +15 °C to +30 °C
Humidity.........................................................................................................................................................................................20 % to 70 %
Shelf Life..........................................................................................................................................................2 years from manufacturing date
ESD Classification (HBM)............................................................................................................................................................................ Class 6
Typical Part Marking
Represents total content. Layout may vary.
How to Order
Agency Recognition
SF - 2923 UC 20 C - 2
SinglFuse™
Product Designator
UL File Number ............................ E500949
U20
Rated Current
20 A
30 A
40 A
50 A
60 A
80 A
100 A
Part Marking
U20
U30
U40
U50
U60
U80
U100
SMD Footprint
2923 = EIA 2923
(7358 metric)
Construction
CERAMIC COVER
Fuse Blow Type
UC = Ultra-High Current
Rated Current
20 ~ 100 (20 A ~ 100 A)
U2
0
Structure Type
C = Ceramic Cube Housing
Packaging Type
- 2 = Tape & Reel
FUSE ELEMENT /
TERMINAL
Packaging Quantity
1,000 pieces per 13-inch reel
Recommended Pad Layout
4.40
(.173)
Product Dimensions
5.80 ± 0.30
(.228 ± .012)
U20
4.20 ± 0.20
(.165 ± .008)
4.00 ± 0.20
(.157 ± .008)
1.30 ± 0.20
(.051 ± .008)
5.80
(.228)
7.30 ± 0.50
(.287 ± .020)
2.70
(.106)
DIMENSIONS:
MM
(INCHES)
DIMENSIONS:
MM
(INCHES)
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
SF-2923UC-C Series – Ultra-High Current SMD Fuses
Current Rating Thermal Derating Curve
120
100
DERATING (%)
80
60
40
25 °C
20
0
-60
-40
-20
0
20
40
60
80
100
120
140
AMBIENT TEMPERATURE (°C)
Pulse Cycle Withstand Capability
100,000
NUMBER OF PULSES
10,000
1,000
100
10 %
100 %
PULSE I
2
t / AVERAGE MELTING I
2
t
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
SF-2923UC-C Series – Ultra-High Current SMD Fuses
Solder Reflow Recommendations
tp
RAMP-UP
TL
CRITICAL ZONE
T L TO TP
TP
Temperature
TS MAX.
tL
RAMP-DOWN
TS MIN.
ts
PREHEAT
Liquidous Temperature (T
L
)
Time (t
L
) maintained above T
L
Peak Package Body
Temperature (T
p
)
Ramp Up Rate (T
smax
to T
L
)
Ramp Up Rate (T
L
to T
p
)
Profile Feature
Preheat / Soak:
Temperature Min. (T
smin
)
Temperature Max. (T
smax
)
Time (t
s
) from (T
smin
to T
smax
)
Pb-Free Assembly
150 °C
200 °C
60~180 seconds
3 °C / second max.
5 °C / second max.
217 °C
60~90 seconds
235 °C ± 5 °C
20~30 seconds*
6 °C / second max.
8 minutes max.
240 °C
25 °C
t 25 *C TO PEAK
Time
Time within 5 °C of actual peak
temperature (T
p
)
Ramp Down Rate (T
p
to T
L
)
Do not exceed
Time 25 °C to Peak Temperature
* Tolerance for peak profile temperature (Tp ) is defined as a
supplier minimum and a user maximum.
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
SF-2923UC-C
mm SMD Trimming Potentiometer
3312 - 2
Series – Ultra-High Current SMD Fuses
Average Pre-Arcing Time vs. Current Curves
50 A A
50
40 A A
40
30
30 A A
20 A A
20
60 A A
60
80 A A
80
100 100 A
A
100 100 A
A
80 A A
80
Average I
2
t vs. t Curves
100100
1000000
1000000
60
60 A A
50 A A
50
40 A A
40
10 10
30 A A
30
PRE-ARCING TIME (SECONDS)
PRE-ARCING TIME (SECONDS)
100000
100000
20 A A
20
1 1
0.1 0.1
0.01
0.01
0.001
0.001
10 10
I
2
t (A
2
s)
I
2
t (A
2
s)
10000
10000
1000
1000
100100
1000
1000
100100
0.001
0.001
0.01
0.01
0.1 0.1
1 1
10 10
100100
CURRENT (A)(A)
CURRENT
TIME (SECONDS)
TIME (SECONDS)
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
[i=s]This post was last edited by azxh on 2016-4-25 15:15[/i] I am a novice and this is my first time drawing a PCB with Altium Designer. I have no experience and I am worried that the board will not ...
There are Samsung, TI, Freescale, etc. in the market, but which one is better for consumer electronics? The biggest disadvantage of Samsung products is that there are too few external interfaces, whic...
Why is the STM32 serial port 2 burnt out, but other parts are not burnt out? The phenomenon is that the serial port 2 can be used at first, but later only the serial port 2 cannot be used, while other...
In the grinding robot system, the contact force between the grinding head and the workpiece is an important factor to ensure the machining accuracy and perform robot force control . The use of CAN com...
I would like to ask all the experts to help me. Can you provide a boost circuit? Requirements: Input: 0.9~1.5V Output: 8V10mA The key is: the boost chip control end can work in the pulse trigger state...
In the actual project development process, it is common to encounter modifications to the hardware circuit, and then the modified part requires the modification of the driver. Thinking about the comi...[Details]
The last two blogs talked about a version problem of STM32CubeMX and the problem of hardware reset. When you solve these two problems, you will find that after the program is burned into the board, t...[Details]
1. Initial understanding of FSMC: FSMC consists of 4 modules: (1) AHB interface (including FSMC configuration register) (2) NOR flash memory and PSRAM controller (when driving LCD, LCD is like a PSRA...[Details]
Automotive LCD Instrument Clock EMI Solution As early as 2014, the market size of China's automotive full LCD instrument has reached 3.506 billion yuan, and it is expected that by 2020, this s...[Details]
China Energy Storage Network:
At the Boao Forum, Zhu Min, the current dean of the National Institute of Finance at Tsinghua University, said: "When talking about blockchain, we must first sep...[Details]
Since China began to try to produce panels independently in 1998, in 2018, China's panel industry has gradually upgraded from a marginal industry to the largest production scale. Especially in the ...[Details]
At the just concluded InfoComm 2018 exhibition, the two major brands, Zhongke Jiguang and China Hualu, both displayed three-color light source
laser TVs
. The outstanding color performance ...[Details]
The adoption rate of serverless
cloud
computing
is gradually increasing, but it has not yet reached people's expectations. Various surveys show that serverless
is
still
an eme...[Details]
I rewrote the main part of this program. The program uses the watchdog as a normal timer and scans the digital tubes in the watchdog interrupt. In addition, I added a display buffer. If you want to d...[Details]
This routine is also a classic routine on the development board. I modified the framework of the program to make it more suitable for future calls. The specific 4*4 keyboard scanning principle is rel...[Details]
The implementation of CAN driver under embedded operating system Android requires not only adding CAN driver device in Linux kernel, but also implementing the call of Android HAL layer. Taking S5...[Details]
1) Independent watchdog has no interrupt, window watchdog has interrupt 2) Independent watchdogs can be divided into hardware and software, while window watchdogs can only be controlled by software...[Details]
At this exhibition, Microsoft brought its flagship intelligent voice products - XiaoIce and Xiaona. In addition, the voice will be equipped with an intelligent face recognition system. Let's see ho...[Details]
Use the STM32 timer input capture module to control 3-way ultrasonic sensors. The ultrasonic sensor used this time is the common HC-SR04, which is often used in the obstacle avoidance system of smal...[Details]
Sensor
京公网安备 11010802033920号
EEWORLD
