The AS7C4098 and AS7C34098 are high-performance CMOS 4,194,304-bit Static Random Access Memory (SRAM) devices
organized as 262,144 words × 16 bits. They are designed for memory applications where fast data access, low power, and
simple interfacing are desired.
Equal address access and cycle times (t
AA
, t
RC
, t
WC
) of 10/12/15/20 ns with output enable access times (t
OE
) of 5/6/7/8 ns are
ideal for high-performance applications. The chip enable input CE permits easy memory expansion with multiple-bank
memory systems.
When CE is High the device enters standby mode. The standard AS7C4098/AS7C34098 is guaranteed not to exceed 110/
72mW power consumption in CMOS standby mode. A write cycle is accomplished by asserting write enable (WE) and chip
enable (CE). Data on the input pins I/O1–I/O16 is written on the rising edge of WE (write cycle 1) or CE (write cycle 2). To
avoid bus contention, external devices should drive I/O pins only after outputs have been disabled with output enable (OE) or
write enable (WE).
A read cycle is accomplished by asserting output enable (OE) and chip enable (CE), with write enable (WE) High. The chip
drives I/O pins with the data word referenced by the input address. When either chip enable or output enable is inactive, or
write enable is active, output drivers stay in high-impedance mode.
These devices provide multiple center power and ground pins, and separate byte enable controls, allowing individual bytes to
be written and read. LB controls the lower bits, I/O1–I/O8, and UB controls the higher bits, I/O9–I/O16.
All chip inputs and outputs are TTL- and CMOS-compatible, and operation is from either a single 5V (AS7C4098) or 3.3V
(AS7C34098) supply. Both devices are available in the JEDEC standard 400-mL, 44-pin SOJ and TSOP 2 packages.
Absolute maximum ratings
Parameter
Voltage on V
CC
relative to GND
Voltage on any pin relative to GND
Power dissipation
Storage temperature
Ambient temperature with V
CC
applied
DC current into outputs (low)
Device
AS7C4098
AS7C34098
Symbol
V
t1
V
t1
V
t2
P
D
T
stg
T
bias
I
OUT
Min
–0.50
–0.50
–0.50
–
–65
–55
–
Max
+7.0
+5.0
V
CC
+0.50
1.5
+150
+125
±20
Unit
V
V
V
W
°C
°C
mA
Note: Stresses greater than those listed under
Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any other conditions outside those indicated in the operational sections of this specification is not implied.
Exposure to absolute maximum rating conditions for extended periods may affect reliability.
Truth table
CE
H
L
L
L
WE
X
H
X
H
OE
X
H
X
L
LB
X
X
H
L
H
L
L
UB
X
X
H
H
L
L
H
L
L
I/O1–I/O8
High Z
High Z
D
OUT
High Z
D
OUT
D
IN
High Z
D
IN
I/O9–I/O16
High Z
High Z
High Z
D
OUT
D
OUT
High Z
D
IN
D
IN
Mode
Standby (I
SB
, I
SB1
)
Output disable (I
CC
)
Read (I
CC
)
L
L
X
H
L
Write (I
CC
)
Key: X = Don’t care, L = Low, H = High.
1/13/05;
v.1.9
Alliance Semiconductor
P. 2 of 10
AS7C4098
AS7C34098
®
Recommended operating conditions
Parameter
AS7C4098
Supply voltage
AS7C34098
AS7C34098
AS7C4098
Input voltage
commercial
industrial
AS7C34098
Symbol
V
CC
(12/15/20)
V
CC
(10)
V
CC
(12/15/20)
V
IH
V
IH
V
IL1
Ambient operating temperature
T
A
T
A
Min Typical
4.5
3.15
3.0
2.2
2.0
–0.5
0
–40
5.0
3.3
3.3
–
–
–
–
–
Max
5.5
3.6
3.6
V
CC
+ 0.5
V
CC
+ 0.5
0.8
70
85
Unit
V
V
V
V
V
V
°C
°C
1 V
IL
min = –1.0V for pulse width less than 5ns.
DC operating characteristics (over the operating range)
What is NB-lot?
NB-IoT, or Narrow Band-Internet of Things, has the characteristics of low cost, low power consumption, and wide coverage (cellular network). It is positioned in the carrier-grade, low-...
I encountered a problem when developing a program on Windows. I personally think it should be a unicode encoding problem. For example, there is the following problem; CString a("$ABCDE"); I personally...
[table] [tr][td][color=#666666]What are the correct ways to use the DIN rail power supply? The following scan IC network will answer for you: [/color] [color=#666666] 1. The AC voltage standards for D...
[i=s]This post was last edited by forever1314 on 2016-5-11 14:44[/i] int main(void) { u8 a,j,i=0; /* config the led */ LED_GPIO_Config(); /*config key*/ Key_GPIO_Config(); while(1) { if( Key_Scan(GPIO...
Since the maximum input voltage of MPS2307DN is 23V, but the current circuit requires 24V input and 3.3 and 5V output, MPS2307 cannot be used. I am looking for a compatible chip. It is best if the PCB...
The rapid development of the Internet has realized high-speed information transmission and resource sharing, greatly facilitating people's lives. Embedded systems are widely used in various electr...[Details]
Assume that data is read from 8-bit AD (if it is a higher-bit AD, the data type can be defined as int), the subroutine is get_ad();
1. Limited secondary filtering
/* A value can be adjust...[Details]
1. Introduction
RFID (radio frequency identification) is a non-contact automatic identification technology that emerged in the 1990s. It uses the characteristics of radio frequency signal prop...[Details]
When the WDP500-2A plane grating monochromator is used to test the emission wavelength of a high-power laser diode at different currents, the matching of the laser diode has the disadvantages of lo...[Details]
Microcontrollers (MCUs), which are widely used in automotive electronics, are rapidly facing time and cost pressures. The main advantage of using MCUs has always been to create high-level system in...[Details]
Floating-point digital signal processing has become a constant requirement for precision technology, often in applications requiring high accuracy in areas such as aviation, industrial machinery, a...[Details]
introduction
Solar cells and LED lighting are typical applications of new energy and energy-saving and efficient technologies. Solar LED lighting uses solar cells to convert solar energy...[Details]
1 Introduction
Solar street lights are mainly composed of four parts: solar photovoltaic cell components, batteries, charge and discharge controllers, and lighting fixtures. The bo...[Details]
Electronic systems are located at different points on the automotive power bus and therefore often need to operate under very stringent power requirements. These include load dump, cold crank, very lo...[Details]
With the continuous improvement of the requirements of intelligent building security systems and the continuous improvement of people's safety awareness, indoor anti-theft has gradually attracted peop...[Details]
1. Introduction
Testing the temperature of steel billets before rolling is an important measure to ensure the quality of steel. Traditional manual testing is difficult to ensure product qu...[Details]
LED lamps and bulbs are now rapidly replacing incandescent, halogen and CFL (compact fluorescent lamp) light sources in many general lighting applications. Flyback DC/DC converters are the power su...[Details]
0 Introduction
With the rise and continuous improvement of the solid-state lighting industry, light-emitting diodes (LEDs) have become an alternative lighting technology and are gr...[Details]
With the advocacy and implementation of the government's Safe City Plan, the security market has increasingly higher requirements for the clarity of surveillance images. Imagine that after a case o...[Details]
Overview
In spectral measurement, photomultiplier tubes (PMT) and charge-coupled devices (CCD) are often used as photoelectric converters. PMT is used in slow-changing, high-precision spectral...[Details]
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
