(Note 2).................................................. –40°C to 125°C
Maximum Junction Temperature........................... 125°C
Storage Temperature Range................... –65°C to 125°C
MS PACKAGE
16-LEAD PLASTIC MSOP
T
JMAX
= 125°C,
θ
JA
= 130°C/W
ORDER INFORMATION
LEAD FREE FINISH
LT3519EMS#PBF
LT3519IMS#PBF
TAPE AND REEL
LT3519EMS#TRPBF
LT3519IMS#TRPBF
PART MARKING*
3519
3519
PACKAGE DESCRIPTION
16-Lead Plastic MSOP
16-Lead Plastic MSOP
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to:
http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to:
http://www.linear.com/tapeandreel/
ELECTRICAL CHARACTERISTICS
PARAMETER
V
IN
Operating Voltage Range
V
IN
Supply Current
The
l
denotes the specifications which apply over the full
operating temperature range, otherwise specifications are at T
A
= 25°C. V
IN
= 12V,
SHDN/UVLO
= 12V, CTRL = 2V, PWM = 5V,
unless otherwise noted.
CONDITIONS
Continuous Operation (Note 3)
SHDN/UVLO
= 0V
(Shutdown)
PWM = 0V
(Idle)
PWM > 1.5V, FB = 1.5V (Active, Not Switching)
ISP = 24V, CTRL = 2V
ISP = 0V, CTRL = 2V
ISP = 24V, CTRL = 100mV
2.5V < ISP < 45V
400kHz (LT3519)
400kHz (LT3519)
l
l
l
MIN
3
TYP
0.1
2.0
2.5
MAX
30
UNITS
V
μA
mA
mA
Current Sense Voltage (V
ISP
-V
ISN
)
Zero Current Sense Voltage (V
ISP
-V
ISN
)
Current Sense Voltage Line Regulation
Switching Frequency
Maximum Duty Cycle
Switch Current Limit
Switch V
CESAT
240
–12
320
94
750
250
250
–6
0.02
400
97
980
300
260
0
440
1150
mV
mV
mV
%/V
kHz
%
mA
mV
I
SW
= 500mA
3519f
2
LT3519
ELECTRICAL CHARACTERISTICS
PARAMETER
Switch Leakage Current
CTRL for Full-Scale LED Current
CTRL Pin Bias Current
PWM Input High Voltage
PWM Input Low Voltage
PWM Pin Resistance to GND
FB Regulation Voltage (V
FB
)
FB Pin Threshold Voltage for
OPENLED
Falling
FB Pin Bias Current
ISP , ISN Idle Input Bias Current
ISP , ISN Full-Scale Input Bias Current
Schottky Forward Drop
Schottky Leakage Current
SHDN/UVLO
Threshold Voltage Falling
SHDN/UVLO
Input Low Voltage
SHDN/UVLO
Pin Bias Current Low
SHDN/UVLO
Pin Bias Current High
V
REF
Output Voltage
V
REF
Output Pin Regulation
OPENLED
Output Low (V
OL
)
OPENLED
Leakage Current
I
VIN
Drops Below 1μA
SHDN/UVLO
= 1.15V
SHDN/UVLO
= 1.30V
–100μA ≤ I
VREF
≤ 0μA
3V < V
IN
< 40V
I
OPENLED
= 1mA
FB = 0V,
OPENLED
= 40V
l
l
The
l
denotes the specifications which apply over the full
operating temperature range, otherwise specifications are at T
A
= 25°C. V
IN
= 12V,
SHDN/UVLO
= 12V, CTRL = 2V, PWM = 5V,
unless otherwise noted.
CONDITIONS
SW = 45V, PWM = 0V
1.2
Current Out of Pin, CTRL = 0.1V
1.5
0.4
70
1.190
1.220
V
FB
– 60mV
Current Out of Pin, FB = 1V
PWM = 0V
ISP = ISN = 24V
I
SCHOTTKY
= 500mA
CATHODE = 24V, ANODE = 0V
l
MIN
TYP
MAX
2
UNITS
μA
V
nA
V
V
kΩ
V
V
nA
μA
μA
V
50
100
1.250
120
1
60
17
0.8
4
1.180
1.8
1.96
1.220
2.2
10
2
1.270
0.4
2.6
100
2.04
0.04
240
1
μA
V
V
μA
nA
V
%/V
mV
μA
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2.
The LT3519E is guaranteed to meet specified performance
from 0°C to 125°C. Specifications over the –40°C to 125°C operating
temperature range are assured by design, characterization and
correlation with statistical process controls. The LT3519I is guaranteed
to meet performance specifications over the –40°C to 125°C operating
temperature range.
Note 3.
Absolute maximum voltage at V
IN
and
OPENLED
is 40V for
nonrepetitive one second transients and 30V for continuous operation.
My old razor was broken. I always wanted to buy one. I was going to use my E coins to buy a range hood. But then my family said they didn't want to buy one. So I bought a Feike razor online. It took l...
UCC3957 is TIM's 3-cell or 4-cell lithium battery protection IC. UCC3957 is a 3-cell or 4-cell lithium-ion battery pack protection IC using BiCMOS technology. It protects the battery pack together wit...
I am working on a motion control card project recently. During the debugging of the prototype, I need to verify the correctness of the CAN bus communication function. In the past, I only knew the CAN ...
May is a nice month, not too cold nor too hot. In this month, people can choose the way they like to dress, regardless of the weather.
May is a sober month, during which there is always a lot of work ...
[i=s] This post was last edited by dontium on 2015-1-23 11:22 [/i] TI (State Council) Commonly Used Operational Amplifier Circuit Collection[b][size=4][/size][/b]...
When playing with the Bluetooth serial port, the data (character type) sent to the serial port assistant is normal when the baud rate is 9600. When I want to add the Bluetooth function, I change the b...
In
circuit design,
current
measurement
is widely used, and the main fields are divided into three categories: in measurement,
the electric meter
is used to measure the curre...[Details]
1. Overview
Will passive devices
produce nonlinear intermodulation distortion? The answer is yes! Although there is no systematic theoretical analysis, it has been found in engineerin...[Details]
5. Identifiers and keywords of C language
A complete PIC microcontroller C language program usually consists of six parts: include files (i.e. header files 1, variable definitions, variable de...[Details]
Editor's note: In order to help technicians or engineers who have knowledge of PIC microcontroller assembly language quickly master the method of using C language to program PIC microcontrollers, t...[Details]
Capacitors
are basic components in various electronic devices and are widely used for bypassing, coupling,
filtering
, tuning, etc. in electronic circuits. However, to use capacitors,...[Details]
Abstract: In recent years, with the establishment and grid-connected power generation of a large number of solar photovoltaic power stations at home and abroad, photovoltaic grid-connected inverter...[Details]
This article will introduce a design method for a distributed control system used in a tracking car, which can perform distributed control of motor modules, sensor modules, and lighting control mod...[Details]
Energy conservation and environmental protection are the main directions of current automotive technology research, and power batteries are the key to electric vehicle technology. Research on powe...[Details]
At present,
the control system used in
automobiles
can be divided into three parts from the functional point of view:
sensor
unit, control unit and execution unit. Among them,
th...[Details]
The number of timers/counters and interrupt sources directly determines the performance of the microcontroller. The MCS-51 microcontroller has two programmable 16-bit timers/counters and five inter...[Details]
Some people believe that hybrid vehicles are just a transitional product, and the ultimate goal of developing new energy vehicles is electric vehicles. Therefore, China should skip hybrid vehicles ...[Details]
Li/SOCl2 batteries (lithium sub-cells) have the advantages of high operating voltage, stable discharge voltage, wide operating temperature range and long storage life, and have been widely used in ...[Details]
As a type of iron battery, lithium iron phosphate battery (hereinafter referred to as lithium iron battery) has always been widely concerned by industry friends (some people say that lithium iron b...[Details]
1. Electromagnetic compatibility design
Electromagnetic compatibility refers to the ability of electronic equipment to work in a coordinated and effective manner in various electromagnetic env...[Details]
Modern communication equipment, portable electronic products, laptops, electric vehicles, small satellites, etc. generally use batteries as power sources and are widely used. However, the batteries...[Details]
Talking
京公网安备 11010802033920号
EEWORLD
