EEWORLDEEWORLDEEWORLD

Part Number

Search

51760-11303615BALF

Description
Board Connector, Female, Right Angle, Solder Terminal, Guide Pin, Receptacle
CategoryThe connector    The connector   
File Size259KB,3 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Environmental Compliance
Download Datasheet Parametric View All

51760-11303615BALF Overview

Board Connector, Female, Right Angle, Solder Terminal, Guide Pin, Receptacle

51760-11303615BALF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerAmphenol
Reach Compliance Codecompliant
Board mount optionsHOLE .086-.098
body width0.47 inch
subject depth0.82 inch
body length8.55 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact completed and terminatedTIN
Contact point genderFEMALE
Contact materialCOPPER ALLOY
Contact resistance20 mΩ
Contact styleHYBRID
Dielectric withstand voltage2500VDC V
Durability200 Cycles
maximum insertion force.973 N
Insulation resistance500000000 Ω
insulator materialGLASS FILLED THERMOPLASTIC
Manufacturer's serial number51760
Mixed contactsYES
Installation option 1GUIDE PIN
Installation option 2LOCKING
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
Maximum operating temperature105 °C
Minimum operating temperature-55 °C
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.09 inch
Termination typeSOLDER
Evacuation force-minimum value.17792 N
PDM: Rev:M
STATUS:
Released
Printed: Dec 20, 2010
.
Output duration of ISE VHDL state machine
I wrote a state machine using when case, but the output of each state control signal only lasts for half a time cycle, and other components cannot react at all. How can I make the output of each case ...
timdong FPGA/CPLD
Flash application problem, the whole segment is erased!
Each time the 430 Flash is erased, it erases the entire segment A or B. If I only want to change one of the data, there is a risk of losing all other data. What should I do? Please give me some good a...
aiwenwen Microcontroller MCU
The problem of hitting the board
This is a pre-drawn board. There are no mistakes in the rule check. Can an expert please help me check if there are any other problems? I now want to take it to a processing factory to print out this ...
NJMKL PCB Design
S9KEAZN64AM MCU reports a fault when using PE to burn .SAP file
fl::target -lc "LC for Simple Flash" fl::target -b 0x1ffffc00 0x1000 fl::target -v off -l off cmdwin::fl::device -d "FTMRH_PFlash64RAM4" -o "16kx32x1" -a 0x0 0xffff cmdwin::fl::erase allBeginning Oper...
willqy NXP MCU
Contiki(3) Run! stm32(f103)
[i=s]This post was last edited by Xin Xin on 2014-11-16 01:42[/i] First of all, let me briefly mention it. After a lot of trouble, I can now successfully run contiki on stm32. Of course, there are man...
辛昕 RF/Wirelessly
Struggle stm32 data
...
qingfenglinxia stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2172  906  2447  1803  709  44  19  50  37  15 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号