The ASM3P2969A uses the most efficient and optimized
modulation profile approved by the FCC and is
implemented by using a proprietary all digital method.
The ASM3P2969A modulates the output of a single PLL
in order to “spread” the bandwidth of a synthesized clock,
and more importantly, decreases the peak amplitudes of
its harmonics. This results in significantly lower system
EMI compared to the typical narrow band signal produced
by oscillators and most frequency generators. Lowering
EMI by increasing a signal’s bandwidth is called ‘spread
spectrum clock generation’.
Applications
The ASM3P2969A is targeted towards all portable
devices with very low power requirements like MP3
players, Notebooks and digital still cameras.
Product Description
The ASM3P2969A is a versatile spread spectrum
frequency modulator designed specifically for a wide
range of clock frequencies. The ASM3P2969A reduces
electromagnetic interference (EMI) at the clock source,
allowing system wide reduction of EMI of
all clock
dependent signals. The ASM3P2969A allows significant
system cost savings by reducing the number of circuit
board layers ferrite beads, shielding that are traditionally
required to pass EMI regulations.
Key Specifications
Description
Supply voltages
Cycle-to-Cycle Jitter
Output Duty Cycle
Modulation Rate Equation
Frequency Deviation
Specification
VDD = 3.3V /2.5V
200pS (Max)
45/55%
F
IN
/256
±1% @ 10MHz
Block Diagram
VDD
Modulation
XIN
XOUT
Crystal
Oscillator
Frequency
Divider
Feedback
Divider
REFOUT/2
DIV/2
Phase
Detector
Loop
Filter
VCO
PLL
Output
Divider
ModOUT
VSS
Alliance Semiconductor
2575 Augustine Drive
•
Santa Clara, CA
•
Tel: 408.855.4900
•
Fax: 408.855.4999
•
www.alsc.com
Notice: The information in this document is subject to change without notice.
September 2005
rev 1.6
Pin Configuration (6-pin TSOT- 23 Package)
ASM3P2969A
REFOUT/2
1
XOUT
2
6
VSS
ModOUT
VDD
ASM3P2969A
5
4
XIN/CLKIN
3
Pin Description
Pin#
1
2
3
4
5
6
Pin Name
REFOUT/2
XOUT
XIN/CLKIN
VDD
ModOUT
VSS
Type
O
O
I
P
O
P
Description
Buffered and divided by 2 output of the input frequency.
Crystal connection. If using an external reference, this pin must be left unconnected.
Crystal connection or external reference frequency input. This pin has dual functions. It
can be connected either to an external crystal or an external reference clock.
Power supply for the entire chip
Spread spectrum clock output.
Ground connection.
Low Power Peak EMI Reducing Solution
Notice: The information in this document is subject to change without notice.
2 of 12
September 2005
rev 1.6
Pin Configuration (8-pin SOIC and TSSOP Packages)
ASM3P2969A
XIN/CLKIN
1
XOUT
2
8
7
6
5
VDD
NC
ModOUT
VSS
ASM3P2969A
REFOUT/2
3
NC
4
Pin Description
Pin#
1
2
3
4
5
6
7
8
Pin Name
XIN/CLKIN
XOUT
REFOUT/2
NC
VSS
ModOUT
NC
VDD
Type
I
O
O
-
P
O
-
P
Description
Crystal connection or external reference frequency input. This pin has dual functions. It
can be connected either to an external crystal or an external reference clock.
Crystal connection. If using an external reference, this pin must be left unconnected.
Buffered and divided by 2 output of the input frequency.
No connect.
Ground connection.
Spread spectrum clock output.
No connect.
Power supply for the entire chip
Modulation Profile
Specifications
Description
Frequency Range
For 2.5V Supply
For 3.3V Supply
Specification
6MHz < CLKIN < 12MHz
6MHz < CLKIN < 13MHz
F
IN
/256
±1% @ 10MHz
Modulation Equation
Frequency Deviation
Low Power Peak EMI Reducing Solution
Notice: The information in this document is subject to change without notice.
3 of 12
September 2005
rev 1.6
Absolute Maximum Ratings
Symbol
VDD, V
IN
T
STG
T
A
T
s
T
J
T
DV
Storage temperature
Operating temperature
Max. Soldering Temperature (10 sec)
Junction Temperature
Static Discharge Voltage
(As per JEDEC STD22- A114-B)
ASM3P2969A
Parameter
Rating
-0.5 to +7.0
-65 to +125
0 to 70
260
150
2
Unit
V
°C
°C
°C
°C
KV
Voltage on any pin with respect to Ground
Note: These are stress ratings only and are not implied for functional use. Exposure to absolute maximum ratings for prolonged periods of time may affect
device reliability.
DC Electrical Characteristics for 2.5V Supply
(Test condition: All parameters are measured at room temperature (+25°C) unless otherwise stated)
Symbol
V
IL
V
IH
I
IL
I
IH
I
XOL
I
XOH
V
OL
V
OH
I
DD
I
CC
VDD
t
ON
Z
OUT
Input low voltage
Input high voltage
Input low current
Input high current
Parameter
Min
VSS - 0.3
2.0
-
-
-
-
-
1.8
-
-
2.375
-
-
Typ
-
-
-
-
3
3
-
-
1.0
2.5
2.5
-
50
Max
0.8
VDD + 0.3
-35
35
-
-
0.6
-
-
-
2.625
5
-
Unit
V
V
µA
µA
mA
mA
V
V
mA
mA
V
mS
Ω
XOUT output low current (@0.5V, VDD=2.5V)
XOUT output high current (@1.8V, VDD=2.5V)
Output low voltage (VDD = 2.5 V, I
OL
= 8mA)
Output high voltage (VDD = 2.5 V, I
OH
= 8mA)
Static supply current *
Dynamic supply current (2.5V, 10MHz and no load)
Operating Voltage
Power-up time (first locked cycle after power-up)
Output impedance
* XIN / CLKIN pin is pulled low
AC Electrical Characteristics for 2.5V Supply
Symbol
CLKIN
ModOUT
f
d
t
LH
*
t
HL
*
t
JC
t
D
Input frequency
Output frequency
Frequency Deviation
Input Frequency = 6MHz
Input Frequency = 12MHz
Parameter
Min
6
6
-
-
0.7
0.4
-
45
Typ
-
-
±1.5
±0.8
1.4
0.9
-
50
Max
12
12
-
-
1.7
1.1
200
55
Unit
MHz
MHz
%
nS
nS
pS
%
Output rise time (measured from 0.7V to 1.7V)
Output fall time (measured from 1.7V to 0.7V)
Jitter (cycle to cycle)
Output duty cycle
* t
LH
and t
HL
are measured into a capacitive load of 15pF
Low Power Peak EMI Reducing Solution
Notice: The information in this document is subject to change without notice.
4 of 12
September 2005
rev 1.6
DC Electrical Characteristics for 3.3V Supply
(Test condition: All parameters are measured at room temperature (+25°C) unless otherwise stated)
ASM3P2969A
Symbol
V
IL
V
IH
I
IL
I
IH
I
XOL
I
XOH
V
OL
V
OH
I
DD
I
CC
VDD
t
ON
Z
OUT
Input low voltage
Input high voltage
Input low current
Input high current
Parameter
Min
VSS - 0.3
2.0
-
-
-
-
-
2.5
-
-
2.7
-
-
Typ
-
-
-
-
3
3
-
-
1.1
3.5
3.3
-
45
Max
0.8
VDD + 0.3
-35
35
-
-
0.4
-
-
-
3.6
5
-
Unit
V
V
µA
µA
mA
mA
V
V
mA
mA
V
mS
Ω
XOUT output low current (@0.4V, VDD=3.3V)
XOUT output high current (@2.5V, VDD=3.3V)
Output low voltage (VDD = 3.3 V, I
OL
= 8mA)
Output high voltage (VDD = 3.3 V, I
OH
= 8mA)
Static supply current *
Dynamic supply current (3.3V, 10MHz and no load)
Operating Voltage
Power-up time (first locked cycle after power-up)
Output impedance
* XIN / CLKIN pin is pulled low
AC Electrical Characteristics for 3.3V Supply
Symbol
CLKIN
ModOUT
f
d
t
LH
*
t
HL
*
t
JC
t
D
Input frequency
Output frequency
Frequency Deviation
Input Frequency = 6MHz
Input Frequency = 13MHz
Parameter
Min
6
6
-
-
0.4
0.4
-
45
Typ
-
-
±1.5
±0.75
1.2
1.0
-
50
Max
13
13
-
-
1.5
1.2
200
55
Unit
MHz
MHz
%
nS
nS
pS
%
Output rise time (measured from 0.8 to 2.0V)
Output fall time (measured at 2.0V to 0.8V)
Jitter (cycle to cycle)
Output duty cycle
*t
LH
and t
HL
are measured into a capacitive load of 15pF
Low Power Peak EMI Reducing Solution
Notice: The information in this document is subject to change without notice.
Contents Chapter 1 Overview of UNIX Operating System 6 1.1 Introduction to UNIX Operating System 6 1.2 Composition of UNIX System 6 1.3 Several Terms Related to UNIX 7 Chapter 2 Common UNIX Operations...
I recently debugged FPGA to write data to RAM. The data bus of RAM is 72 bits and the address bus is 20 bits. Since the same data needs to be written to 6 RAMs, the design is made like this: the exter...
Let’s start with a simple question: How fast can the GPIO flip speed of STM32 (for example, used to simulate timing) be? Write a piece of code to test: [code]void test(void) { for(;;) { GPIOA->ODR = (...
Assume that data is read from 8-bit AD (if it is a higher-bit AD, the data type can be defined as int), the subroutine is get_ad();
1. Limited secondary filtering
/* A value can be adjust...[Details]
Today, with the increasing integration of functions, mobile phones can also be used as portable media players (PMP), digital cameras, handheld computers (PDAs), and even global positioning systems ...[Details]
introduction
Throughout the history of automotive lighting, power has always played an important role. Initially, cars only needed headlights to see the road in the dark. Later, other light so...[Details]
Floating-point digital signal processing has become a constant requirement for precision technology, often in applications requiring high accuracy in areas such as aviation, industrial machinery, a...[Details]
1 Introduction
Solar street lights are mainly composed of four parts: solar photovoltaic cell components, batteries, charge and discharge controllers, and lighting fixtures. The bo...[Details]
With the rapid development of urban economy, elevators are increasingly used as a vertical transportation tool. However, elevator fault detection and maintenance, especially the role of elevator remot...[Details]
LED is the abbreviation of light emitting diode, which is an electric light source made of semiconductor technology. The core part of LED is a chip composed of P-type semiconductor and N-type semi...[Details]
I've been studying dot matrix recently. It looks simple, but it takes a while to master it completely! The 8*8 dot matrix hardware circuit I'm making now is like this. The row is driven by 74HC138 + t...[Details]
Overview
In spectral measurement, photomultiplier tubes (PMT) and charge-coupled devices (CCD) are often used as photoelectric converters. PMT is used in slow-changing, high-precision spectral...[Details]
Motors are important products that convert electrical energy into mechanical energy to achieve automation, and they are widely used in industrial control, medical electronics, white a...[Details]
It is well known to automotive suppliers that automakers are demanding more from their supply base. For connector suppliers, this means stricter requirements for product performance, stability and ...[Details]
According to the Industrial Technology Research Institute of Taiwan, due to factors such as the oil crisis and global warming, the issues of energy conservation and environmental protection have at...[Details]
The era of mobile access to the Internet has arrived, and it will rapidly change the business and infrastructure needs of mobile operators under a whole new trend of requirements. We need 4G LTE to...[Details]
Introduction
Nowadays, people pay more and more attention to the security alarm system, and people have higher and higher requirements for the functions and performance of the alarm. This paper prop...[Details]
Introduction
In industrial control, speed measurement is often required. Generally, a contact tachometer is used. This tachometer must be placed against the center of the shaft to measure. It...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
