I used the typical 89C52 MCU control + 74LS04 drive transmission + CX20106 receiver circuit on the Internet. There is no problem with welding, and the distance measurement can be achieved. But the max...
[i=s]This post was last edited by chenzhufly on 2019-6-11 00:32[/i]The main changes were to the power supply, adding a serial port and JTAG for easier debugging. As for the SD card, there is no plan t...
I have been working on FPGA design for a while. I have experienced the joy of solving problems and the pain of searching for results and answers. Now I will summarize the problems and mistakes I often...
[size=4]I use the IO port of the microcontroller to drive the relay through the 8050 transistor. After the microcontroller is powered on, the IO port outputs a high level, hoping that the relay will w...
Dong Yang, executive vice president of the China Association of Automobile Manufacturers, said on the 26th that according to the authorization of the Ministry of Industry and Information Technology...[Details]
On April 24, Sungrow released its annual financial report. The report shows that in 2017, Sungrow's global shipments reached 16.5GW, of which domestic shipments reached 13.2GW, a year-on-year incre...[Details]
There has been a lot of news about Huawei
phones
recently
. At the
Huawei
Global Analyst Conference
on the 17th
,
Huawei
announced that it will launch
5G
phones
in the seco...[Details]
Since China began to try to produce panels independently in 1998, in 2018, China's panel industry has gradually upgraded from a marginal industry to the largest production scale. Especially in the ...[Details]
Autonomous driving
and
5G
are the two hot topics that global companies and media are paying the most attention to, and the combination of the two is the focus of everyone's attention....[Details]
This program mainly uses the comparison output function of the timer to generate PWM waves to control the LED. The comparison output of timer A corresponds to P2.3 P2.4. Therefore, a matching working...[Details]
I rewrote the main part of this program. The program uses the watchdog as a normal timer and scans the digital tubes in the watchdog interrupt. In addition, I added a display buffer. If you want to d...[Details]
1. Brief description A summary of "How to build uClinux kernel transplantation on ARMSYS development board with S3C44B0X as core", including the analysis of Bootloader function and the key co...[Details]
Why does MCU have a watchdog? With this question, let's learn about watchdogs. Even the 51 single-chip microcomputer has a watchdog, which shows that this dog has a special meaning to us. The purpose...[Details]
When STM32 uses JTMS (PA13) and JTCK (PA14) as normal I/O ports, add the following code before initialization (the order cannot be reversed): RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO, ENABLE); G...[Details]
Note: This STM32 microcontroller is the STM32F103 series. The ADC of Stm32 has DMA function. This is beyond doubt and is what we use most! However, if we want to sample a signal (such as a pulse sign...[Details]
In the 80C51 single-chip microcomputer, the clock frequency is known to be 6MHz. Please program P1.0 and P1.1 to output square waves with periods of 2s and 0.5s respectively. Please give the answer a...[Details]
Manually assemble the following program machine code and analyze the execution function of the program segment. CLR A MOV R2, A MOV R7, #4 LOOP: CLR C MOV A, R0 RLC...[Details]
It is required to use timer/counter 1 for timing, with a timing of 1 second; timer/counter 0 for counter, and the external pulse to be counted is connected from P3.4 (T0). The microcontroller will co...[Details]
Circuit: Using AT89S52 single chip microcomputer. P3.0 to P3.3 are connected to four external buttons. P3.4 to P3.7 are the bit selection ports for controlling the four digital tubes, and P1 is the s...[Details]
51mcu
京公网安备 11010802033920号
EEWORLD
