EEWORLDEEWORLDEEWORLD

Part Number

Search

M55342E11B556AMTF

Description
RESISTOR, THIN FILM, 0.05 W, 0.1 %, 25 ppm, 556 ohm, SURFACE MOUNT, 0402, CHIP
CategoryPassive components    The resistor   
File Size111KB,4 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

M55342E11B556AMTF Overview

RESISTOR, THIN FILM, 0.05 W, 0.1 %, 25 ppm, 556 ohm, SURFACE MOUNT, 0402, CHIP

M55342E11B556AMTF Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
MakerVishay
package instructionSMT, 0402
Reach Compliance Codecompliant
Other featuresNON-INDUCTIVE, LASER TRIMMABLE
structureRectangular
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package height0.254 mm
Package length1.016 mm
Package formSMT
Package width0.559 mm
method of packingTR, Embossed, 7 Inch
Rated power dissipation(P)0.05 W
Rated temperature70 °C
GuidelineMIL-PRF-55342
resistance556 Ω
Resistor typeFIXED RESISTOR
size code0402
surface mountYES
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Terminal shapeWRAPAROUND
Tolerance0.1%
Operating Voltage30 V
E/H (Military M/D55342)
Vishay Thin Film
QPL MIL-PRF-55342 Qualified Thin Film Resistor Chips
FEATURES
Established reliability, “R” failure rate level (100 ppm), C = 2
High purity alumina substrate 99.6 % purity
Wraparound termination featuring a tenacious adhesion
layer covered with an electroplated nickel barrier layer for
+ 150 °C operating conditions
Very low noise and voltage coefficient
(< - 25 dB, 0.5 ppm/V)
Non-inductive
Laser-trimmed tolerances ± 0.1 %
Wraparound resistance less than 0.010
Ω
typical
In-lot tracking less than 5 ppm/°C
Complete MIL-testing available in-house
Antistatic waffle pack or tape and reel packaging available
Military/aerospace/QPL
SURFACE MOUNT
CHIPS
Actual Size
M55342/02
Thin Film Mil chip resistors feature all sputtered wraparound
termination for excellent adhesion and dimensional
uniformity. They are ideal in applications requiring stringent
performance requirements. Established reliability is assured
through 100 % screening and extensive environmental lot
testing. Wafer is sawed producing exact dimensions and
clean, straight edges.
Note
Specification changed
MIL-PRF-55342
by
DSCC
from
MIL-R-55342
to
CONSTRUCTION
TYPICAL PERFORMANCE
ABS
Passivation
Resistor film
Solder
coating
Nickel barrier
High ourity
alumina substrate
Adhesion layer
TCR
TOL
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
Test
Material
Absolute TCR
Absolute Tolerance
Stability:
ΔR
Absolute
Voltage Coefficient
Operating Temperature Range
Storage Temperature Range
Noise
Shelf Life Stability
SPECIFICATIONS
Passivated nichrome
± 25 ppm/°C to ± 300 ppm/°C TCR
± 0.1 %
± 0.1 %
± 0.5 ppm/V
- 55 °C to + 125 °C
- 55 °C to + 150 °C
- 25 dB
100 ppm
1 year at + 25 °C
- 55 °C to + 125 °C
+ 25 °C
2000 h at + 70 °C
CONDITIONS
www.vishay.com
50
For technical questions, contact:
thin-film@vishay.com
Document Number: 60018
Revision: 16-Sep-09
【Design Tools】ChipScope Pro User Guide ---- Attached code and test waveforms
This article introduces how to use ChipScope Prothrough a specific example , gives the whole code , and ModelSim simulation results. I have tried this example and can get the desired results, so I rec...
GONGHCU FPGA/CPLD
533MHz Processor S3C2443 Wiring Guide
The same applies to S3C2450. The BGA spacing of S3C2443 is 0.5mm, which is much higher than the 0.8mm of S3C2410 and S3C2440, and requires a much higher PCB process, and blind holes need to be made....
gina MCU
How can I give the following circuit a signal source for simulation?
The passband signal frequency obtained after filtering by the above circuit is required to be around 60KHZ. How to simulate the signal source (the software I use is multisim)? Could you please explain...
州平卞 Analog electronics
What is 5v tolerance?
Can a 5V tolerant pin be connected directly to a 5V power supply without damage? Can a non-5V tolerant pin be connected to a 5V power supply with a resistor in series (using its internal clamp protect...
kjxxbjb stm32/stm8
【TI recommended course】Recommendation #Consumer Electronics Application and Design Seminar#
//training.eeworld.com.cn/TI/show/course/5540...
lukouGao TI Technology Forum
Sampling clock design of V2.0~
Consider that the clock frequency is greater than 100MHz, and the phase should be relatively accurate. Moreover, when the sampled signal is 50M, in order to achieve an effective resolution of more tha...
FLT9006 DIY/Open Source Hardware

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2783  958  927  1045  2094  57  20  19  22  43 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号