EEWORLDEEWORLDEEWORLD

Part Number

Search

326173U016HT1

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 16V, 75% +Tol, 10% -Tol, 17000uF, Through Hole Mount, RADIAL LEADED, ROHS COMPLIANT
CategoryPassive components    capacitor   
File Size963KB,4 Pages
ManufacturerCDE [ CORNELL DUBILIER ELECTRONICS ]
Environmental Compliance  
Download Datasheet Parametric View All

326173U016HT1 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 16V, 75% +Tol, 10% -Tol, 17000uF, Through Hole Mount, RADIAL LEADED, ROHS COMPLIANT

326173U016HT1 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerCDE [ CORNELL DUBILIER ELECTRONICS ]
package instruction,
Reach Compliance Codecompli
ECCN codeEAR99
capacitance17000 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
diameter22.6 mm
dielectric materialsALUMINUM (WET)
ESR14.9 mΩ
JESD-609 codee3
leakage current0.2607 mA
length92.7 mm
Manufacturer's serial number326
Installation featuresTHROUGH HOLE MOUNT
negative tolerance10%
Number of terminals2
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package shapeCYLINDRICAL PACKAGE
Package formRadial
polarityPOLARIZED
positive tolerance75%
Rated (DC) voltage (URdc)16 V
ripple current3793.4 mA
series326
surface mountNO
Terminal surfaceTin (Sn)
Terminal pitch7.62 mm
Terminal shapeWIRE
Type 325/326,
–55 ºC to 125 ºC Long-Life, Switching Power Grade Radial
High Temperature and Ultra-Low ESR
The Types 325 and 326 are the ultra-wide-temperature, low-ESR
capacitors for switching power-supply outputs and automotive applications.
The 125 °C capability and exceptionally low ESRs enable high ripple-
current capability. With series inductance of 12 to 16 nH and ripple currents
to 27 amps one of these capacitors can save by replacing eight to ten of the
12.5 mm diameter capacitors routinely at the output of switching power
supplies. Type 325 has three leads for rugged, reverse-proof mounting, and
Type 326 has two leads
.
Highlights
2000 hour life test at 125 °C
Ripple Current to 27 amps
ESRs to 5 m
> 90% capacitance at –40 °C
Replaces multiple capacitors
Type 325
Type 326
Specifications
Operating Temperature:
Rated Voltage:
Capacitance:
Capacitance Tolerance:
Leakage Current:
Cold Impedance:
Ripple Current Multipliers:
–55 °C to 125 °C
6.3 to 63 Vdc –
880 µF to 46,000 µF
–10 +75%
≤0.5 √CV µA, 4 mA max, 5 minutes
–55 °C multiple of 25 °C Z ≤2.5 @ 120 Hz
≤20 from 20–100 kHz
Ambient Temperature
45ºC
1.39
120 Hz
see ratings
55ºC
1.3
65ºC
1.21
75ºC
1.11
85ºC
1.00
95ºC
0.88
105ºC
0.73
1 kHz
0.85
115ºC 125ºC
0.55
0.26
20-100 kHz
1.00
Frequency
360 Hz
0.76
400 Hz
0.77
Life Test:
Load Life:
Complies with the EU Directive
2002/95/EC requirement
restricting the use of Lead (Pb),
Mercury (Hg), Cadmium (Cd),
Shelf
Hexavalent chromium (Cr(VI)),
PolyBrominated Biphenyls
(PBB) and PolyBrominated
Diphenyl Ethers (PBDE).
Life:
Outline Drawings
Vibration:
2000 h with rated voltage at 125 °C
∆ capacitance ± 10%
ESR 125 % of limit
DCL 100 % of limit
4000 h at full load at 85 °C
∆ capacitance ± 10%
ESR 200 % of limit
DCL 100 % of limit
500 h at 105 °C,
∆ capacitance ± 10%,
ESR 110% of limit,
DCL 200% of limit
10 to 55 Hz, 0.06” and 10 g max, 2 h each plane
L
+0.015
-0.032
L
CDM Cornell Dubilier
140 Technology Place
Liberty, SC 29657
Phone: (864)843-2277
Fax: (864)843-3800
www.cde.com
Which expert please give me some advice: Bias of signal waveform
Could any expert please give me some advice on the bias of the signal waveform? I want to offset a triangle wave with a base point of 2.5V, a maximum point of 3.6V, and a minimum point of 1.3V to the ...
kibby0 Analog electronics
Problems on connecting the neutral points of two DC circuits with different voltages
[i=s]This post was last edited by sunboy25 on 2017-6-6 10:08[/i] I would like to ask why the circuit can still work normally after the two neutral points A and B in the circuit diagram below are conne...
sunboy25 Power technology
This week's highlights
[url=https://e2echina.ti.com/question_answer/dsp_arm/sitara_arm/f/25/t/134026][font=微软雅黑][size=4]EtherCAT implemented based on CPSW of AM335x[/size][/font][/url][font=微软雅黑][size=4][color=#000000] [/co...
橙色凯 DSP and ARM Processors
Talk about my IRIG-B custom component design and debugging summary based on SOPC
Keywords: SOPC, custom component, IRIG-B, debugging [b]I. Case description [/b] Recently, I plan to use SOPC to build a system to complete the upgrade of the project platform. Since the platform based...
wdgui522 FPGA/CPLD
The main components of switching power supply: switching power supply transformer, switching power supply principle and design (serial 47)
[b]Chapter 2 Main Components of Switching Power Supply 2-1. Switching Power Supply Transformer[/b] Modern electronic equipment has higher and higher technical performance indicators such as working ef...
noyisi112 Power technology
Questions about pspice simulation
[img=110,0]https://bbs.eeworld.com.cn/forum.php?mod=image&aid=358477&size=300x300&key=ba87408b2bb9203f&nocache=yes&type=fixnone[/img][size=12px][size=18px][color=#333333][backcolor=transparent][font=微...
ATneva Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 933  1270  2018  1641  888  19  26  41  34  18 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号