AT29C512-15 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > storage> AT29C512-15

AT29C512-15: Description64K X 8 FLASH 5V PROM, 90 ns, PQCC32; Categorystorage; File Size198KB，18 Pages; ManufacturerAtmel (Microchip)

Download Datasheet Parametric Compare View All

AT29C512-15 Overview

64K X 8 FLASH 5V PROM, 90 ns, PQCC32

AT29C512-15 Parametric

Parameter Name	Attribute value
Number of functions	1
Number of terminals	32
Maximum operating temperature	70 Cel
Minimum operating temperature	0.0 Cel
Maximum supply/operating voltage	5.5 V
Minimum supply/operating voltage	4.5 V
Rated supply voltage	5 V
maximum access time	90 ns
Processing package description	Plastic, MS-016AE, LCC-32
state	DISCONTINUED
Craftsmanship	CMOS
packaging shape	Rectangle
Package Size	ChipCARRIER
surface mount	Yes
Terminal form	J BEND
Terminal spacing	1.27 mm
terminal coating	tin lead
Terminal location	Four
Packaging Materials	Plastic/Epoxy
Temperature level	COMMERCIAL
memory width	8
organize	64K × 8
storage density	524288 deg
operating mode	ASYNCHRONOUS
Number of digits	65536 words
Number of digits	64K
Memory IC type	FLASH 5V programmable read-only memory
serial parallel	parallel
Maximum TWC of write cycle	10 ms

Preview

Download Datasheet

View All

Features

•

Fast Read Access Time – 70 ns

•

5-volt Only Reprogramming

•

Sector Program Operation

– Single Cycle Reprogram (Erase and Program)

– 512 Sectors (128 Bytes/Sector)

– Internal Address and Data Latches for 128 Bytes

Internal Program Control and Timer

Hardware and Software Data Protection

Fast Sector Program Cycle Time – 10 ms

DATA Polling for End of Program Detection

Low Power Dissipation

– 50 mA Active Current

– 100 µA CMOS Standby Current

Typical Endurance > 10,000 Cycles

Single 5V ± 10% Supply

CMOS and TTL Compatible Inputs and Outputs

Commercial and Industrial Temperature Ranges

Green (Pb/Halide-free) Packaging Option

•

512K (64K x 8)

5-volt Only

Flash Memory

AT29C512

•

1. Description

The AT29C512 is a 5-volt only in-system Flash programmable and erasable read only

memory (PEROM). Its 512K of memory is organized as 65,536 words by 8 bits. Man-

ufactured with Atmel’s advanced nonvolatile CMOS technology, the device offers

access times to 70 ns with power dissipation of just 275 mW over the commercial tem-

perature range. When the device is deselected, the CMOS standby current is less

than 100 µA. The device endurance is such that any sector can typically be written to

in excess of 10,000 times.

To allow for simple in-system reprogrammability, the AT29C512 does not require high

input voltages for programming. Five-volt-only commands determine the operation of

the device. Reading data out of the device is similar to reading from an EPROM.

Reprogramming the AT29C512 is performed on a sector basis; 128 bytes of data are

loaded into the device and then simultaneously programmed.

During a reprogram cycle, the address locations and 128 bytes of data are internally

latched, freeing the address and data bus for other operations. Following the initiation

of a program cycle, the device will automatically erase the sector and then program

the latched data using an internal control timer. The end of a program cycle can be

detected by DATA polling of I/O7. Once the end of a program cycle has been

detected, a new access for a read or program can begin.

0456H–FLASH–2/05

AT29C512

3. Block Diagram

4. Device Operation

4.1

Read

The AT29C512 is accessed like an EPROM. When CE and OE are low and WE is high, the data

stored at the memory location determined by the address pins is asserted on the outputs. The

outputs are put in the high impedance state whenever CE or OE is high. This dual-line control

gives designers flexibility in preventing bus contention.

4.2

Byte Load

Byte loads are used to enter the 128 bytes of a sector to be programmed or the software codes

for data protection. A byte load is performed by applying a low pulse on the WE or CE input with

CE or WE low (respectively) and OE high. The address is latched on the falling edge of CE or

WE, whichever occurs last. The data is latched by the first rising edge of CE or WE.

4.3

Program

The device is reprogrammed on a sector basis. If a byte of data within a sector is to be changed,

data for the entire sector must be loaded into the device. Any byte that is not loaded during the

programming of its sector will be indeterminate. Once the bytes of a sector are loaded into the

device, they are simultaneously programmed during the internal programming period. After the

first data byte has been loaded into the device, successive bytes are entered in the same man-

ner. Each new byte to be programmed must have its high-to-low transition on WE (or CE) within

150 µs of the low-to-high transition of WE (or CE) of the preceding byte. If a high-to-low transi-

tion is not detected within 150 µs of the last low-to-high transition, the load period will end and

the internal programming period will start. A7 to A15 specify the sector address. The sector

address must be valid during each high-to-low transition of WE (or CE). A0 to A6 specify the

byte address within the sector. The bytes may be loaded in any order; sequential loading is not

required. Once a programming operation has been initiated, and for the duration of t

, a read

operation will effectively be a polling operation.

0456H–FLASH–2/05

4.4

Software Data Protection

A software controlled data protection feature is available on the AT29C512. Once the software

protection is enabled a software algorithm must be issued to the device before a program may

be performed. The software protection feature may be enabled or disabled by the user; when

shipped from Atmel, the software data protection feature is disabled. To enable the software

data protection, a series of three program commands to specific addresses with specific data

must be performed. After the software data protection is enabled the same three program com-

mands must begin each program cycle in order for the programs to occur. All software program

commands must obey the sector program timing specifications. Once set, the software data pro-

tection feature remains active unless its disable command is issued. Power transitions will not

reset the software data protection feature; however, the software feature will guard against inad-

vertent program cycles during power transitions.

Once set, software data protection will remain active unless the disable command sequence is

issued.

After setting SDP, any attempt to write to the device without the 3-byte command sequence will

start the internal write timers. No data will be written to the device; however, for the duration of

, a read operation will effectively be a polling operation.

After the software data protection’s 3-byte command code is given, a byte load is performed by

applying a low pulse on the WE or CE input with CE or WE low (respectively) and OE high. The

address is latched on the falling edge of CE or WE, whichever occurs last. The data is latched by

the first rising edge of CE or WE. The 128 bytes of data must be loaded into each sector by the

same procedure as outlined in the program section under device operation.

4.5

Hardware Data Protection

Hardware features protect against inadvertent programs to the AT29C512 in the following ways:

(a) V

sense – if V

is below 3.8V (typical), the program function is inhibited; (b) V

power on

delay – once V

has reached the V

sense level, the device will automatically time out 5 ms

(typical) before programming; (c) Program inhibit – holding any one of OE low, CE high or WE

high inhibits program cycles; and (d) Noise filter – pulses of less than 15 ns (typical) on the WE

or CE inputs will not initiate a program cycle.

4.6

Product Identification

The product identification mode identifies the device and manufacturer as Atmel. It may be

accessed by hardware or software operation. The hardware operation mode can be used by an

external programmer to identify the correct programming algorithm for the Atmel product. In

addition, users may wish to use the software product identification mode to identify the part (i.e.,

using the device code), and have the system software use the appropriate sector size for pro-

gram operations. In this manner, the user can have a common board design for 256K to 4-

megabit densities and, with each density’s sector size in a memory map, have the system soft-

ware apply the appropriate sector size.

For details, see Operating Modes (for hardware operation) or Software Product Identification.

The manufacturer and device code is the same for both modes.

AT29C512

0456H–FLASH–2/05

AT29C512-15 Related Products

	AT29C512-15	29C512	AT29C512-12PC	AT29C512-12	AT29C512-15PI	AT29C512-70	AT29C512-70PC	AT29C512-15PC	AT29C512-90	AT29C512-90PC
Description	64K X 8 FLASH 5V PROM, 90 ns, PQCC32	64K X 8 FLASH 5V PROM, 90 ns, PQCC32	64K X 8 FLASH 5V PROM, 90 ns, PQCC32	64K X 8 FLASH 5V PROM, 90 ns, PQCC32	64K X 8 FLASH 5V PROM, 90 ns, PQCC32	64K X 8 FLASH 5V PROM, 90 ns, PQCC32	64K X 8 FLASH 5V PROM, 90 ns, PQCC32	64K X 8 FLASH 5V PROM, 90 ns, PQCC32	64K X 8 FLASH 5V PROM, 90 ns, PQCC32	64K X 8 FLASH 5V PROM, 90 ns, PQCC32
Number of functions	1	1	1	1	1	1	1	1	1	1
Number of terminals	32	32	32	32	32	32	32	32	32	32
Maximum operating temperature	70 Cel	70 Cel	70 °C	70 Cel	85 °C	70 Cel	70 °C	70 °C	70 Cel	70 °C
Minimum operating temperature	0.0 Cel	0.0 Cel	-	0.0 Cel	-40 °C	0.0 Cel	-	-	0.0 Cel	-
surface mount	Yes	Yes	NO	Yes	NO	Yes	NO	NO	Yes	NO
Terminal form	J BEND	J BEND	THROUGH-HOLE	J BEND	THROUGH-HOLE	J BEND	THROUGH-HOLE	THROUGH-HOLE	J BEND	THROUGH-HOLE
Terminal location	Four	Four	DUAL	Four	DUAL	Four	DUAL	DUAL	Four	DUAL
Temperature level	COMMERCIAL	COMMERCIAL	COMMERCIAL	COMMERCIAL	INDUSTRIAL	COMMERCIAL	COMMERCIAL	COMMERCIAL	COMMERCIAL	COMMERCIAL
memory width	8	8	8	8	8	8	8	8	8	8
organize	64K × 8	64K × 8	64KX8	64K × 8	64KX8	64K × 8	64KX8	64KX8	64K × 8	64KX8

Recommended Resources

Schematic diagram of a distributed power supply system

Homemade 9-stop timer circuit

Integrated voltage regulator application circuit commonly used in automobiles 03

Switch electromagnet drive circuit diagram

555 motorcycle DC ignition circuit

Circuit composed of isolation amplifier Burr-Brown3652

Electromagnetic compatibility design at circuit board level: This application note discusses electromagnetic compatibility ( EMC ) design at the circuit board level from the aspects of component selection, circuit design, and printed circuit board layout . This...; 风亦路 PCB Design

Is there any MP3 decoding library?: I want to use ESP32 to play MP3. I already have an IIS amplifier board and an SPI TF card plug-in. I want to play music, but it can only play WAV. Can I ask the experts how to soft-decode MP3 and then...; lemon1394 MicroPython Open Source section

The most basic question about AVR: I made a circuit board with attiny13, and wanted to adjust it, but the software didn't listen to me. I installed AVR STDIO 4 and other C software, but none of them could compile. I uninstalled them al...; uyang4050 Embedded System

MicroPython has over 10,000 stars on GitHub!: ...; dcexpert MicroPython Open Source section

MSP430G2553 State Machine Modeling: The program requires that if p1.3 is pressed short, p1.0 will be inverted, and if p1.3 is pressed long, p1.6 will be inverted. The following is the program: #include "msp430g2553.h" #define IDLE 0 #de...; Aguilera Microcontroller MCU

Registration for the 2020 ADI Test and Measurement Technology Solution Exchange is now open! Participants can win an oscilloscope grand prize!: Registration for the 2020 ADI Test and Measurement Technology Solution Exchange is now open! Participants can win an oscilloscope grand prize!Time: 13:00-16:30, November 16th Location: Shanghai New In...; EEWORLD社区 Test/Measurement

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components