AT29C512-70PC datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > storage> storage> AT29C512-70PC

AT29C512-70PC: Description64K X 8 FLASH 5V PROM, 90 ns, PQCC32; Categorystorage storage; File Size198KB，18 Pages; ManufacturerAtmel (Microchip)

Download Datasheet Parametric Compare View All

AT29C512-70PC Overview

64K X 8 FLASH 5V PROM, 90 ns, PQCC32

AT29C512-70PC Parametric

Parameter Name	Attribute value
Is it Rohs certified?	incompatible
Maker	Atmel (Microchip)
Parts packaging code	DIP
package instruction	DIP, DIP32,.6
Contacts	32
Reach Compliance Code	unknow
ECCN code	EAR99
Maximum access time	70 ns
command user interface	NO
Data polling	YES
Durability	10000 Write/Erase Cycles
JESD-30 code	R-PDIP-T32
JESD-609 code	e0
length	42.037 mm
memory density	524288 bi
Memory IC Type	FLASH
memory width	8
Number of functions	1
Number of departments/size	512
Number of terminals	32
word count	65536 words
character code	64000
Operating mode	ASYNCHRONOUS
Maximum operating temperature	70 °C
Minimum operating temperature
organize	64KX8
Output characteristics	3-STATE
Package body material	PLASTIC/EPOXY
encapsulated code	DIP
Encapsulate equivalent code	DIP32,.6
Package shape	RECTANGULAR
Package form	IN-LINE
page size	128 words
Parallel/Serial	PARALLEL
Peak Reflow Temperature (Celsius)	NOT SPECIFIED
power supply	5 V
Programming voltage	5 V
Certification status	Not Qualified
Maximum seat height	4.826 mm
Department size	128
Maximum standby current	0.0001 A
Maximum slew rate	0.05 mA
Maximum supply voltage (Vsup)	5.25 V
Minimum supply voltage (Vsup)	4.75 V
Nominal supply voltage (Vsup)	5 V
surface mount	NO
technology	CMOS
Temperature level	COMMERCIAL
Terminal surface	Tin/Lead (Sn/Pb)
Terminal form	THROUGH-HOLE
Terminal pitch	2.54 mm
Terminal location	DUAL
Maximum time at peak reflow temperature	NOT SPECIFIED
switch bit	YES
type	NOR TYPE
width	15.24 mm
Maximum write cycle time (tWC)	10 ms

Preview

Download Datasheet

View All

Features

•

Fast Read Access Time – 70 ns

•

5-volt Only Reprogramming

•

Sector Program Operation

– Single Cycle Reprogram (Erase and Program)

– 512 Sectors (128 Bytes/Sector)

– Internal Address and Data Latches for 128 Bytes

Internal Program Control and Timer

Hardware and Software Data Protection

Fast Sector Program Cycle Time – 10 ms

DATA Polling for End of Program Detection

Low Power Dissipation

– 50 mA Active Current

– 100 µA CMOS Standby Current

Typical Endurance > 10,000 Cycles

Single 5V ± 10% Supply

CMOS and TTL Compatible Inputs and Outputs

Commercial and Industrial Temperature Ranges

Green (Pb/Halide-free) Packaging Option

•

512K (64K x 8)

5-volt Only

Flash Memory

AT29C512

•

1. Description

The AT29C512 is a 5-volt only in-system Flash programmable and erasable read only

memory (PEROM). Its 512K of memory is organized as 65,536 words by 8 bits. Man-

ufactured with Atmel’s advanced nonvolatile CMOS technology, the device offers

access times to 70 ns with power dissipation of just 275 mW over the commercial tem-

perature range. When the device is deselected, the CMOS standby current is less

than 100 µA. The device endurance is such that any sector can typically be written to

in excess of 10,000 times.

To allow for simple in-system reprogrammability, the AT29C512 does not require high

input voltages for programming. Five-volt-only commands determine the operation of

the device. Reading data out of the device is similar to reading from an EPROM.

Reprogramming the AT29C512 is performed on a sector basis; 128 bytes of data are

loaded into the device and then simultaneously programmed.

During a reprogram cycle, the address locations and 128 bytes of data are internally

latched, freeing the address and data bus for other operations. Following the initiation

of a program cycle, the device will automatically erase the sector and then program

the latched data using an internal control timer. The end of a program cycle can be

detected by DATA polling of I/O7. Once the end of a program cycle has been

detected, a new access for a read or program can begin.

0456H–FLASH–2/05

AT29C512

3. Block Diagram

4. Device Operation

4.1

Read

The AT29C512 is accessed like an EPROM. When CE and OE are low and WE is high, the data

stored at the memory location determined by the address pins is asserted on the outputs. The

outputs are put in the high impedance state whenever CE or OE is high. This dual-line control

gives designers flexibility in preventing bus contention.

4.2

Byte Load

Byte loads are used to enter the 128 bytes of a sector to be programmed or the software codes

for data protection. A byte load is performed by applying a low pulse on the WE or CE input with

CE or WE low (respectively) and OE high. The address is latched on the falling edge of CE or

WE, whichever occurs last. The data is latched by the first rising edge of CE or WE.

4.3

Program

The device is reprogrammed on a sector basis. If a byte of data within a sector is to be changed,

data for the entire sector must be loaded into the device. Any byte that is not loaded during the

programming of its sector will be indeterminate. Once the bytes of a sector are loaded into the

device, they are simultaneously programmed during the internal programming period. After the

first data byte has been loaded into the device, successive bytes are entered in the same man-

ner. Each new byte to be programmed must have its high-to-low transition on WE (or CE) within

150 µs of the low-to-high transition of WE (or CE) of the preceding byte. If a high-to-low transi-

tion is not detected within 150 µs of the last low-to-high transition, the load period will end and

the internal programming period will start. A7 to A15 specify the sector address. The sector

address must be valid during each high-to-low transition of WE (or CE). A0 to A6 specify the

byte address within the sector. The bytes may be loaded in any order; sequential loading is not

required. Once a programming operation has been initiated, and for the duration of t

, a read

operation will effectively be a polling operation.

0456H–FLASH–2/05

4.4

Software Data Protection

A software controlled data protection feature is available on the AT29C512. Once the software

protection is enabled a software algorithm must be issued to the device before a program may

be performed. The software protection feature may be enabled or disabled by the user; when

shipped from Atmel, the software data protection feature is disabled. To enable the software

data protection, a series of three program commands to specific addresses with specific data

must be performed. After the software data protection is enabled the same three program com-

mands must begin each program cycle in order for the programs to occur. All software program

commands must obey the sector program timing specifications. Once set, the software data pro-

tection feature remains active unless its disable command is issued. Power transitions will not

reset the software data protection feature; however, the software feature will guard against inad-

vertent program cycles during power transitions.

Once set, software data protection will remain active unless the disable command sequence is

issued.

After setting SDP, any attempt to write to the device without the 3-byte command sequence will

start the internal write timers. No data will be written to the device; however, for the duration of

, a read operation will effectively be a polling operation.

After the software data protection’s 3-byte command code is given, a byte load is performed by

applying a low pulse on the WE or CE input with CE or WE low (respectively) and OE high. The

address is latched on the falling edge of CE or WE, whichever occurs last. The data is latched by

the first rising edge of CE or WE. The 128 bytes of data must be loaded into each sector by the

same procedure as outlined in the program section under device operation.

4.5

Hardware Data Protection

Hardware features protect against inadvertent programs to the AT29C512 in the following ways:

(a) V

sense – if V

is below 3.8V (typical), the program function is inhibited; (b) V

power on

delay – once V

has reached the V

sense level, the device will automatically time out 5 ms

(typical) before programming; (c) Program inhibit – holding any one of OE low, CE high or WE

high inhibits program cycles; and (d) Noise filter – pulses of less than 15 ns (typical) on the WE

or CE inputs will not initiate a program cycle.

4.6

Product Identification

The product identification mode identifies the device and manufacturer as Atmel. It may be

accessed by hardware or software operation. The hardware operation mode can be used by an

external programmer to identify the correct programming algorithm for the Atmel product. In

addition, users may wish to use the software product identification mode to identify the part (i.e.,

using the device code), and have the system software use the appropriate sector size for pro-

gram operations. In this manner, the user can have a common board design for 256K to 4-

megabit densities and, with each density’s sector size in a memory map, have the system soft-

ware apply the appropriate sector size.

For details, see Operating Modes (for hardware operation) or Software Product Identification.

The manufacturer and device code is the same for both modes.

AT29C512

0456H–FLASH–2/05

AT29C512-70PC Related Products

	AT29C512-70PC	29C512	AT29C512-12PC	AT29C512-12	AT29C512-15PI	AT29C512-15	AT29C512-70	AT29C512-15PC	AT29C512-90	AT29C512-90PC
Description	64K X 8 FLASH 5V PROM, 90 ns, PQCC32	64K X 8 FLASH 5V PROM, 90 ns, PQCC32	64K X 8 FLASH 5V PROM, 90 ns, PQCC32	64K X 8 FLASH 5V PROM, 90 ns, PQCC32	64K X 8 FLASH 5V PROM, 90 ns, PQCC32	64K X 8 FLASH 5V PROM, 90 ns, PQCC32	64K X 8 FLASH 5V PROM, 90 ns, PQCC32	64K X 8 FLASH 5V PROM, 90 ns, PQCC32	64K X 8 FLASH 5V PROM, 90 ns, PQCC32	64K X 8 FLASH 5V PROM, 90 ns, PQCC32
memory width	8	8	8	8	8	8	8	8	8	8
Number of functions	1	1	1	1	1	1	1	1	1	1
Number of terminals	32	32	32	32	32	32	32	32	32	32
Maximum operating temperature	70 °C	70 Cel	70 °C	70 Cel	85 °C	70 Cel	70 Cel	70 °C	70 Cel	70 °C
Minimum operating temperature	-	0.0 Cel	-	0.0 Cel	-40 °C	0.0 Cel	0.0 Cel	-	0.0 Cel	-
organize	64KX8	64K × 8	64KX8	64K × 8	64KX8	64K × 8	64K × 8	64KX8	64K × 8	64KX8
surface mount	NO	Yes	NO	Yes	NO	Yes	Yes	NO	Yes	NO
Temperature level	COMMERCIAL	COMMERCIAL	COMMERCIAL	COMMERCIAL	INDUSTRIAL	COMMERCIAL	COMMERCIAL	COMMERCIAL	COMMERCIAL	COMMERCIAL
Terminal form	THROUGH-HOLE	J BEND	THROUGH-HOLE	J BEND	THROUGH-HOLE	J BEND	J BEND	THROUGH-HOLE	J BEND	THROUGH-HOLE
Terminal location	DUAL	Four	DUAL	Four	DUAL	Four	Four	DUAL	Four	DUAL

Recommended Resources

Water resistor anti-speed protection circuit

Motor restart circuit after power outage

W723 extended output current voltage stabilizing circuit

Voice control turns on the circuit

Full duplex telephone system circuit diagram

TDA1489 power amplifier circuit

A question about signals and systems: When the player speed increases, the sound becomes higher. This is because the spectrum of the electrical signal becomes wider. But why does the spectrum of the sound become wider? Please give me some...; stream DSP and ARM Processors

I wrote a program code for the CPLD to read and write data as a DSP peripheral. Can an expert tell me if there is any problem?: When CPLD is used as a DSP peripheral, DSP puts the data in the IO space, CPLD reads the data, and controls the peripheral operation program according to the corresponding address and information. I w...; happysee FPGA/CPLD

SensorTile Unboxing: It took about 20 days from application to review and then to receiving the board. During these 20 days, I have been thinking about how to design this set of products. Now I finally got it and started ...; 李炳1991 MEMS sensors

MSP430 Program Library Overview: My initial contact with msp430 came from the book "MSP430 Series Microcontroller System Engineering Design and Practice" published by the Machinery Industry Press. I started to participate in electron...; Engin Microcontroller MCU

Generation and elimination of self-excitation

[size=4]Since self-excitation is harmful to the circuit, the conditions for self-excitation should be destroyed during design and production to reduce or eliminate its harm to the circuit. The followi...

fish001 Analogue and Mixed Signal

Showing the process of WEBENCH design + FPGA power supply

FPGA power supply load design...

pleasemissme Analogue and Mixed Signal

Design ideas and codes for waking up portable devices with simple gestures

This article discusses how to wake up a touch-sensitive device such as a tablet without touching the device, using basic gesture recognition and novel proximity sensors. The article discusses the p...[Details]

Design of street lamp energy-saving device based on PWM

1 Introduction With the acceleration of the pace of urban modernization, society has higher requirements for urban road lighting and urban lighting projects. The state has clearly required tha...[Details]

Using ZLGCAN Interface Function Library in LabVIEW

1. Overview The Virtual CAN Interface (VCI) function library is an application program interface specifically provided for the use of ZLGCAN devices on PCs. The functions in the library ar...[Details]

Design of paper machine transmission control system based on Profibus DP

1. Project Introduction Shandong Dezhou Xingtai Paper Co., Ltd. is a newly built high-end paperboard production enterprise with domestic leading level established by Shandong Zhaodongfang Pape...[Details]

Microsoft plans to launch a Windows-based cloud system

This week, Microsoft held its 2012 Microsoft Worldwide Partner Conference (WPC) in Toronto, Canada. At the conference, Microsoft showed its new products and services to partners around the world. A...[Details]

Improving the efficiency of gear motors

With concerns about the growing energy crisis, motor efficiency has become an important and timely topic. This is because motors use 63% to 70% of the electricity produced in the United States and ...[Details]

Receiving and forwarding infrared remote control signals

Infrared remote control is widely used in home appliances, but the remote controls produced are not compatible with each other. The universal remote controls commonly seen on the market can only co...[Details]

Power Electronics in Automotive Systems

I. Introduction The use of electronics in cars dates back to the early 20th century when electric starters replaced hand cranks. Automotive electronics became popular in the 1960s with the...[Details]

How to set and adjust PID parameters

PID is proportional differential adjustment. You can refer to the detailed introduction in the automatic control course for details! The positive action and the negative action in temperature contr...[Details]

Marine instrument EMC and compass safety distance

According to the National Shipbuilding Industry Economic Research Center, the total shipbuilding capacity in my country last year was about 9×106t. The new ship orders exceeded 17×106t, accounting ...[Details]

Engine test system based on fieldbus

1. Introduction Diesel engine test is the last key process in the diesel engine production process, which plays a very important role in the manufacturing quality of diesel engines. Its main c...[Details]

City Bus Information Integrated Control System Based on CAN Bus

1 Introduction With the continuous development of electronic technology, automotive electronic technology has also developed rapidly. The number of various electronic control units on automobi...[Details]

Voltage and current feedback amplifiers are almost identical

The construction of voltage and current feedback amplifier application circuits is generally the same, except for a few key points. Current feedback amplifiers have higher sl...[Details]

Analysis of battery operation and maintenance work

Different places have accumulated certain experience in equalizing charging of battery packs, but it is difficult to master it properly. Long-term non-equalizing charging or frequent equalizing cha...[Details]

Basic knowledge of power quality

Power quality refers to the quality of AC power supplied to the user end through the public power grid. In an ideal state, the public power grid should supply power to users at a constant frequency...[Details]

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components

M55342M12B12F1C-W

212Y1012N328FN

5962F9684503QYA

ALP12M2-HSH-64

54122-114-45-1500RLF

A13KP-CF

12VR1H15B1N502C3

MMSD-25-30-F-03.25-D-G-MDX-M

AME8500BEETAE15

KPC6N139LTLD

1.5KE170CA_B0_10001

CRH2512F13R3E04Z

Popular Articles

From flying cars to intelligent robot horses, the plot behind Xpeng's technological muscle display

Rohde & Schwarz launches R&S VSESIM-VSS, combining EDA simulation and hardware testing

Discussion on sensor fusion and domain control architecture in automotive ADAS systems

Wafer foundry orders cut in Q4? Why does the industry's view differ from Morgan Stanley's?

Xiaomi launches smart glasses Explorer Edition, supports calls, photos, and navigation

Soil Tester Product Introduction

HIRO deploys next-generation scalable edge micro data center

Surpass Yourself, Pursue Global Dreams | RT-Thread Developer Conference Concludes Successfully!

Apple Music releases 2021 music memory playlist: all the songs you love

Wearable student safety positioning system based on iBeacon Bluetooth 4.0

Technical ResourceMore

\"Circuit Fundamentals\" edited by Wang Huiling

Application of MAX038 in Precision Frequency Synthesis Waveform Generator

CCD camera technical parameters

51 MCU test board circuit diagram - schematic diagram

Ultrasonic distance measurement digital tube display

Research on signal filtering and denoising based on wavelet transform

Controlling AC Signal Offset and Amplitude Using a Dual-Channel Multiplying DAC and a Single IV Converter

Chapter 5_VHDL_State Machine

WP217 - Estimate actual output timing without board simulation

OPTI-LOOP architecture reduces output capacitance and improves transient response