EEWORLDEEWORLDEEWORLD

Part Number

Search

B1RJH-JH

Description
TOGGLE SWITCH,STRAIGHT,SPDT,ON-ON,PC TAIL TERMINAL,TOGGLE BAT,7
Categoryunclassified   
File Size256KB,8 Pages
ManufacturerOhmite
Websitehttps://www.ohmite.com
Download Datasheet Parametric View All

B1RJH-JH Overview

TOGGLE SWITCH,STRAIGHT,SPDT,ON-ON,PC TAIL TERMINAL,TOGGLE BAT,7

B1RJH-JH Parametric

Parameter NameAttribute value
Lead-freeYes
EU RoHS regulationsYes
stateACTIVE
terminal coatingGOLD OVER NICKEL
Manufacturer SeriesB
Switch typeTOGGLE SWITCH
Series B
Toggles
Process Sealed Subminiature Antistatic Toggles
A
General
Specifications
Electrical Capacity (Resistive Load)
Logic Level:
0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Note: Find additional explanation of operating range in Supplement section.
Pushbuttons
Rockers
Other Ratings
Programmable Illuminated PB
Contact Resistance:
Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Nominal Operating Force:
Keylocks
Contact Timing:
Angle of Throw:
50 milliohms maximum
500 megohms minimum @ 500V DC
500V AC minimum for 1 minute minimum
100,000 operations minimum for On-None-On & On-Off-On
50,000 operations minimum for other circuits
50,000 operations minimum for locking lever models
50,000 operations minimum
Toggles A, A1, E & K with Long Paddle: 1.47N (momentary); 1.18N (maintained)
Toggles J & H & K with Short Paddle: 2.72N (momentary); 1.84N (maintained)
Toggle L: 0.59N
Nonshorting (break-before-make)
26°
Materials & Finishes
Rotaries
Toggle:
Bushing:
Gasket:
Case Housing:
Support Bracket:
Movable Contact:
Stationary Contacts:
Terminals:
Nickel plated brass
Carbon blended polyamide; nickel plated zinc alloy for locking levers & threaded bushing
Nitrile butadiene rubber
Glass fiber reinforced polyamide
Tin plated phosphor bronze
Phosphor bronze with gold plating
Copper alloy with gold plating
Copper alloy with gold plating
Tactiles
Slides
Environmental Data
Operating Temperature Range:
Humidity:
Vibration:
Shock:
–30°C through +85°C (–22°F through +185°F)
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
50G (490m/s
2
) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Tilt
Touch
Installation
Mounting Torque:
.30 ~ .45Nm (2.65 ~ 3.98 lb
in) for A1 actuator with threaded bushing only
PCB Processing
Indicators
Soldering:
Cleaning:
Wave Soldering Recommended: See Profile A in Supplement section.
Manual Soldering: See Profile A in Supplement section.
Automated cleaning. See Cleaning specifications in Supplement section.
Accessories
Standards & Certifications
Flammability Standards:
Supplement
UL94V-0 available
The B Series toggles have not been tested for UL recognition or CSA certification.
These switches are designed for use in a low-voltage, low-current, logic-level circuit.
When used as intended in a logic-level circuit, the results do not produce hazardous energy.
A12
www.nkk.com
Need help 24V 100mA working current sensorless built-in MOS three-phase brushless motor driver chip
Need three-phase brushless motor driver chip Voltage: DC 24V Working current: 100mA No sensor Built-in MOSIf you have resources, please contact 452446843[url=home.php?mod=spaceuid=803337]@qq.com[/url]...
涛之苍穹 Motor Drive Control(Motor Control)
(A-Current Signal Detection Device) First Prize of Zhejiang Province_Hangzhou Dianzi University
[align=center][font=微软雅黑, "][size=14px][align=left]This design uses STM32F407 as the core to achieve isolated current measurement. Use TDA2030 to power amplify the input signal, and the current is tra...
sigma Electronics Design Contest
What is the Report ID in HID?
Hello everyone: I need to control a USB sound card via HID. I have successfully opened the USB device and called HidP_GetCaps. But when writing data via WriteFile, there is a problem. The API document...
jingdongbo Embedded System
【Altera soc experience tour】+ Implementation of wireless routing design based on ad hoc network on FPGA-SOC (3)
FPGA software part of the intermediate frequency design of DUC design of PFIR design This scheme requires the design of a 72-order 3-fold interpolation programmable FIR filter (i.e. PFIR), with an inp...
muhan9 FPGA/CPLD
【Discussion】Capture mode pulse counting
I want to use 430 to measure the number of pulses of an external input pulse in 1 second. I use Timer_A to set the timer for 1 second, and then define the input pin as capture mode. Every time a pulse...
wujieling Microcontroller MCU
EEWORLD University Hall----Hands on Sensorless 2(B)
Hands on Sensorless 2(B):https://training.eeworld.com.cn/course/181...
dongcuipin Talking

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1489  2463  2467  218  1712  30  50  5  35  52 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号