CAUTION: Stresses above those listed in “Absolute Maximum Ratings” can permanently damage the device. This is a stress only rating and operation of the device at
these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
5.
JA
is measured with the component mounted on a low-effective thermal conductivity test board in free air. See
TB379
for details.
6. Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications.
(
Electrical Specifications
PARAMETER
DC CHARACTERISTICS
Driver Differential V
OUT
(No Load)
Driver Differential V
OUT
(with Load)
Change in Magnitude of Driver
Differential V
OUT
for
Complementary Output States
Driver Common-Mode V
OUT
Change in Magnitude of Driver
Common-Mode V
OUT
for
Complementary Output States
Logic Input High Voltage
Logic Input Low Voltage
Logic Input Current
Input Current (A/Y, B/Z), (Note
15)
Test Conditions: V
CC
= 4.5V to 5.5V; Unless Otherwise Specified. Typicals are at V
CC
= 5V, T
A
= +25°C,
Note 7
SYMBOL
TEST CONDITIONS
TEMP
(°C)
MIN
TYP
MAX
UNIT
V
OD1
V
OD2
V
OD
R = 50Ω (RS-422), (Figure
1)
R = 27Ω (RS-485), (Figure
1)
R = 27Ω or 50Ω, (Figure
1)
Full
Full
Full
Full
-
2
1.5
-
-
3
2.3
0.01
V
CC
-
5
0.2
V
V
V
V
V
OC
V
OC
R = 27Ω or 50Ω, (Figure
1)
R = 27Ω or 50Ω, (Figure
1)
Full
Full
-
-
-
0.01
3
0.2
V
V
V
IH
V
IL
I
IN1
I
IN2
I
IN2
DE, DI, RE
DE, DI, RE
DE, DI, RE
DE = 0V, V
CC
= 4.5 to
5.5V
DE = 0V, V
CC
= 0V
-7V
V
CM
12V
V
CM
= 0V
I
O
= -4mA, V
ID
= 200mV
I
O
= -4mA, V
ID
= 200mV
0.4V
V
O
2.4V
-7V
V
CM
12V
V
IN
= 12V
V
IN
= -7V
V
IN
= 12V
V
IN
= -7V
Full
Full
Full
Full
Full
Full
Full
Full
25
Full
Full
Full
Full
2
-
-2
-
-
-
-
-0.2
-
3.5
-
-
96
-
-
-
-
-
-
-
-
70
-
-
-
-
-
0.8
2
140
-120
180
-100
0.2
-
-
0.4
1
-
V
V
µA
µA
µA
µA
µA
V
mV
V
V
µA
kΩ
Receiver Differential Threshold
Voltage
Receiver Input Hysteresis
Receiver Output High Voltage
Receiver Output Low Voltage
Three-State (High Impedance)
Receiver Output Current
Receiver Input Resistance
V
TH
V
TH
V
OH
V
OL
I
OZR
R
IN
FN6051 Rev.8.00
Sep 20, 2018
Page 4 of 16
ISL8487E, ISL81487L, ISL81487E
Electrical Specifications
PARAMETER
No-Load Supply Current, (Note
8)
Test Conditions: V
CC
= 4.5V to 5.5V; Unless Otherwise Specified. Typicals are at V
GPIO operations can be performed through the sys file system interface. When the file system operates GPIO, you must first check whether the GPIO you want to operate is occupied by other drivers. If i...
Everyone: I don't know why when I download NK, it always gets stuck at [b]Sp=ffffc7cc [/b] Windows CE Kernel for ARM (Thumb Enabled) Built on Aug 4 2008 at 18:38:38 ProcessorType=0411 Revision=7 sp_ab...
There are a lot of movies, mp3s, and software stored on the computer hard disk. How to use the mobile phone to directly access the hard disk resources through wifi without connecting to the line, play...
Today's computer peripherals are pursuing high speed and high versatility. In order to meet user needs, seven companies led by Intel launched the USB (Universal Serial Bus) bus protocol in 1994, wh...[Details]
This program is written to simulate the serial port hardware mechanism. When used, a timed interrupt can be set with a time interval of 1/4 baud rate. The receiving function is called once for ea...[Details]
Assume that data is read from 8-bit AD (if it is a higher-bit AD, the data type can be defined as int), the subroutine is get_ad();
1. Limited secondary filtering
/* A value can be adjust...[Details]
1. Introduction
Since the 1980s, with the continuous development of automotive electronic technology, there are more and more electronic control units in automobiles, such as electronic fuel i...[Details]
Floating-point digital signal processing has become a constant requirement for precision technology, often in applications requiring high accuracy in areas such as aviation, industrial machinery, a...[Details]
System design is a complex process. It is not enough to just use ICs. There are many details to consider. This article uses a high-fidelity music playback system as an example to introduce how to s...[Details]
1 Introduction
Solar street lights are mainly composed of four parts: solar photovoltaic cell components, batteries, charge and discharge controllers, and lighting fixtures. The bo...[Details]
DSP (digital signal processor) is used more and more frequently in today's engineering applications. There are three main reasons for this: first, it has powerful computing power and is capable of ...[Details]
The solidification and modularization of intelligent video analysis algorithms are the current trends in the application of intelligent video analysis technology. It perfectly combines intelligent ...[Details]
1 Introduction
As an emerging microfabrication technology, micro-electromechanical system (MEMS) technology has begun to be applied in various fields. It can integrate functions such as inform...[Details]
With the rapid development of urban economy, elevators are increasingly used as a vertical transportation tool. However, elevator fault detection and maintenance, especially the role of elevator remot...[Details]
1. What is temperature?
Heat is a type of molecular motion. The hotter an object is, the faster its molecules move. Absolute zero is defined as the temperature at which all molecular motion ...[Details]
LED is the abbreviation of light emitting diode, which is an electric light source made of semiconductor technology. The core part of LED is a chip composed of P-type semiconductor and N-type semi...[Details]
Flooded Batteries
This battery developed in Germany can be used to power flashlights, strobe lights and toys as long as it is filled with water. This battery can be stored for 50 years and can...[Details]
Overview
In spectral measurement, photomultiplier tubes (PMT) and charge-coupled devices (CCD) are often used as photoelectric converters. PMT is used in slow-changing, high-precision spectral...[Details]
Special Edition for Assessment Centres
京公网安备 11010802033920号
EEWORLD
