DATASHEET
ISL8487E, ISL81487L, ISL81487E
±15kV ESD Protected, 1/8 Unit Load, 5V, Low Power, High Speed or Slew Rate
Limited RS-485/RS-422 Transceivers
The
ISL8487E, ISL81487L,
and
ISL81487E
RS-485/RS-422
devices are ESD protected, fractional unit load (UL),
BiCMOS, 5V powered, single transceivers that meet both
the RS-485 and RS-422 standards for balanced
communication. Each driver output/receiver input is
protected against ±15kV ESD strikes without latch-up. Unlike
competitive devices, this device family is specified for 10%
tolerance supplies (4.5V to 5.5V).
All devices present a 1/8 unit load to the RS-485 bus, which
allows up to 256 transceivers on the network for large node
count systems (for example, process automation and remote
meter reading systems). In a remote utility meter reading
system, individual utility meter readings (in apartments, for
example) are routed to a concentrator with an RS-485
network, so the high allowed node count minimizes the
number of repeaters required to network all the meters. Data
for all meters is then read out from the concentrator from a
single access port or a wireless link.
Slew rate limited drivers on the ISL8487E and ISL81487L
reduce EMI and minimize reflections from improperly
terminated transmission lines or unterminated stubs in
multidrop and multipoint applications. Data rates up to
250kbps are achievable with these devices.
Data rates up to 5Mbps are achievable by using the
ISL81487E, which features higher slew rates.
The receiver (Rx) inputs feature a “fail-safe if open” design,
which ensures a logic high Rx output if Rx inputs are floating.
The driver (Tx) outputs are short-circuit protected, even for
voltages exceeding the power supply voltage. Additionally,
on-chip thermal shutdown circuitry disables the Tx outputs to
prevent damage if power dissipation becomes excessive.
The half duplex devices multiplex the Rx inputs and Tx
outputs to allow transceivers with Rx and Tx disable
functions in 8 lead packages.
FN6051
Rev.8.00
Sep 20, 2018
Features
• RS-485 I/O pin ESD protection . . . . . . . . . . . ±15kV HBM
- Class 3 ESD level on all other pins . . . . . . . >7kV HBM
• Fractional unit load allows up to 256 devices on the bus
• Specified for 10% tolerance supplies
• High data rate version (ISL81487E) . . . . . . . up to 5Mbps
• Slew rate limited versions for error free data
transmission (ISL8487E, ISL81487L) . . . . .up to 250kbps
• Low current shutdown mode (except ISL81487E) . . . 0.5µA
• Low quiescent supply current:
- ISL8487E, ISL81487L . . . . . . . . . . . 145µA (maximum)
- ISL81487E . . . . . . . . . . . . . . . . . . . . 420µA (maximum)
• -7V to +12V common mode input voltage range
• Three state Rx and Tx outputs
• 30ns propagation delays, 5ns skew (ISL81487E)
• Half duplex pinouts
• Operate from a single +5V supply (10% tolerance)
• Current limiting and thermal shutdown for driver overload
protection
• Pin compatible replacements for: MAX487E, (ISL8487E);
LTC1487, ADM1487 (ISL81487L); MAX1487E, ST485ER
(ISL81487E)
• Pb-free plus anneal available (RoHS compliant)
Applications
• High node count networks
• Automated utility meter reading systems
• Factory automation
• Security networks
• Building environmental control systems
• Industrial/process control networks
Related Literature
For a full list of related documents, visit our website:
•
ISL8487E, ISL81487L,
and
ISL81487E
product pages
TABLE 1. SUMMARY OF FEATURES
PART
NUMBER
ISL8487E
ISL81487L
ISL81487E
HALF/FULL
DUPLEX
Half
Half
Half
NO. OF DEVICES
DATA RATE
ALLOWED ON BUS
(Mbps)
256
256
256
0.25
0.25
5
SLEW RATE
LIMITED?
Yes
Yes
No
RECEIVER/
QUIESCENT LOW POWER
PIN
DRIVER ENABLE?
I
CC
(A)
SHUTDOWN? COUNT
Yes
Yes
Yes
120
120
350
Yes
Yes
No
8
8
8
FN6051 Rev.8.00
Sep 20, 2018
Page 1 of 16
ISL8487E, ISL81487L, ISL81487E
Typical Operating Circuits
To calculate the resistor values, refer to
TB509.
Ordering Information
PART NUMBER ()
ISL8487EIBZ
ISL8487EIBZ-T
PART MARKING
8487EIBZ
8487EIBZ
TEMP. RANGE (°C)
-40 to +85
-40 to +85
-40 to +85
TAPE AND REEL
(UNITS) (Note
1)
-
2.5k
-
PACKAGE
8 Ld SOIC
(Pb-free)
8 Ld SOIC
(Pb-free)
PKG. DWG. #
M8.15
M8.15
8487EIPZ
ISL8487EIPZ
(not
recommended for new designs,
recommended replacement
ISL81487LIPZ)
ISL81487LIBZ
ISL81487LIBZ-T
ISL81487LIPZ
ISL81487EIBZ
ISL81487EIBZ-T
ISL81487EIPZ
NOTES:
1. Refer to
TB347
for details about reel specifications.
81487LIBZ
81487LIBZ
81487LIPZ
81487EIBZ
81487EIBZ
ISL81487EIPZ
8 Ld PDIP
E8.3
(Pb-free,
Note 4)
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-
2.5k
-
-
2.5k
-
8 Ld SOIC
(Pb-free)
8 Ld SOIC
(Pb-free)
M8.15
M8.15
E8.3
8 Ld PDIP
(Pb-free,
Note 4)
8 Ld SOIC
(Pb-free)
8 Ld SOIC
(Pb-free)
M8.15
M8.15
8 Ld PDIP
E8.3
(Pb-free,
Note 4)
2. Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate
termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Pb-free products are MSL
classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020
3. For Moisture Sensitivity Level (MSL), see the
ISL8487E, ISL81487L,
and
ISL81487E
product information pages. For more information about
MSL, see
TB363.
4. Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications.
FN6051 Rev.8.00
Sep 20, 2018
Page 2 of 16
ISL8487E, ISL81487L, ISL81487E
Pinout
PDIP, SOIC
TOP VIEW
RO 1
RE 2
DE 3
DI 4
D
8
7
6
5
V
CC
B/Z
A/Y
GND
R
Pin Descriptions
PIN
RO
RE
DE
DI
GND
A/Y
B/Z
V
CC
FUNCTION
Receiver output. RO is high if A > B by at least 0.2V; RO is low if A < B by 0.2V or more; RO is high if A and B are unconnected (floating).
Receiver output enable. RO is enabled when RE is low; RO is high impedance when RE is high.
Driver output enable. The driver outputs Y and Z are enabled by bringing DE high. They are high impedance when DE is low.
Driver input. A low on DI forces output Y low and output Z high. Similarly, a high on DI forces output Y high and output Z low.
Ground connection.
15kV
HBM ESD protected, RS-485/422 level, noninverting receiver input and noninverting driver output. Pin is an input (A) if DE = 0;
pin is an output (Y) if DE = 1.
15kV
HBM ESD protected, RS-485/422 level, inverting receiver input and inverting driver output. Pin is an input (B) if DE = 0; pin is
an output (Z) if DE = 1.
System power supply input (4.5V to 5.5V).
Truth Tables
TRANSMITTING
INPUTS
RE
X
X
0
1
DE
1
1
0
0
DI
1
0
X
X
Z
0
1
High-Z
High-Z
(Note
12)
OUTPUTS
Y
1
0
High-Z
High-Z
(Note
12)
RE
0
0
0
1
1
RECEIVING
INPUTS
DE
X
X
X
X
0
A-B
≥ +0.2V
≤ -0.2V
Inputs Open
X
X
OUTPUT
RO
1
0
1
High-Z
(Note
12)
High-Z
FN6051 Rev.8.00
Sep 20, 2018
Page 3 of 16
ISL8487E, ISL81487L, ISL81487E
Absolute Maximum Ratings
V
CC
to Ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V
Input Voltages
DI, DE, RE . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to (V
CC
+0.5V)
Input/Output Voltages
A/Y, B/Z . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -8V to +12.5V
RO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to (V
CC
+0.5V)
Short-Circuit Duration
Y, Z . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous
ESD Rating . . . . . . . . . . . . . . . . . . . . See
“Electrical Specifications”
Thermal Information
Thermal Resistance (Typical,
Note 5)
JA
(°C/W)
8 Ld SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . .
170
140
8 Ld PDIP Package (Note
6)
. . . . . . . . . . . . . . . . . .
Maximum Junction Temperature (Plastic Package) . . . . . . . 150°C
Maximum Storage Temperature Range . . . . . . . . . . . -65°C to 150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C
(SOIC - Lead Tips Only)
Operating Conditions
Temperature Range
ISL8XXXIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to 85°C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” can permanently damage the device. This is a stress only rating and operation of the device at
these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
5.
JA
is measured with the component mounted on a low-effective thermal conductivity test board in free air. See
TB379
for details.
6. Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications.
(
Electrical Specifications
PARAMETER
DC CHARACTERISTICS
Driver Differential V
OUT
(No Load)
Driver Differential V
OUT
(with Load)
Change in Magnitude of Driver
Differential V
OUT
for
Complementary Output States
Driver Common-Mode V
OUT
Change in Magnitude of Driver
Common-Mode V
OUT
for
Complementary Output States
Logic Input High Voltage
Logic Input Low Voltage
Logic Input Current
Input Current (A/Y, B/Z), (Note
15)
Test Conditions: V
CC
= 4.5V to 5.5V; Unless Otherwise Specified. Typicals are at V
CC
= 5V, T
A
= +25°C,
Note 7
SYMBOL
TEST CONDITIONS
TEMP
(°C)
MIN
TYP
MAX
UNIT
V
OD1
V
OD2
V
OD
R = 50Ω (RS-422), (Figure
1)
R = 27Ω (RS-485), (Figure
1)
R = 27Ω or 50Ω, (Figure
1)
Full
Full
Full
Full
-
2
1.5
-
-
3
2.3
0.01
V
CC
-
5
0.2
V
V
V
V
V
OC
V
OC
R = 27Ω or 50Ω, (Figure
1)
R = 27Ω or 50Ω, (Figure
1)
Full
Full
-
-
-
0.01
3
0.2
V
V
V
IH
V
IL
I
IN1
I
IN2
I
IN2
DE, DI, RE
DE, DI, RE
DE, DI, RE
DE = 0V, V
CC
= 4.5 to
5.5V
DE = 0V, V
CC
= 0V
-7V
V
CM
12V
V
CM
= 0V
I
O
= -4mA, V
ID
= 200mV
I
O
= -4mA, V
ID
= 200mV
0.4V
V
O
2.4V
-7V
V
CM
12V
V
IN
= 12V
V
IN
= -7V
V
IN
= 12V
V
IN
= -7V
Full
Full
Full
Full
Full
Full
Full
Full
25
Full
Full
Full
Full
2
-
-2
-
-
-
-
-0.2
-
3.5
-
-
96
-
-
-
-
-
-
-
-
70
-
-
-
-
-
0.8
2
140
-120
180
-100
0.2
-
-
0.4
1
-
V
V
µA
µA
µA
µA
µA
V
mV
V
V
µA
kΩ
Receiver Differential Threshold
Voltage
Receiver Input Hysteresis
Receiver Output High Voltage
Receiver Output Low Voltage
Three-State (High Impedance)
Receiver Output Current
Receiver Input Resistance
V
TH
V
TH
V
OH
V
OL
I
OZR
R
IN
FN6051 Rev.8.00
Sep 20, 2018
Page 4 of 16
ISL8487E, ISL81487L, ISL81487E
Electrical Specifications
PARAMETER
No-Load Supply Current, (Note
8)
Test Conditions: V
CC
= 4.5V to 5.5V; Unless Otherwise Specified. Typicals are at V
CC
= 5V, T
A
= +25°C,
Note 7
(Continued)
SYMBOL
I
CC
TEST CONDITIONS
ISL81487E, DI, RE = 0V DE = V
CC
or V
CC
DE = 0V
ISL8487E, ISL81487L,
DI, RE = 0V or V
CC
DE = V
CC
DE = 0V
TEMP
(°C)
Full
Full
Full
Full
Full
Full
Full
MIN
-
-
-
-
-
35
7
TYP
400
350
160
120
0.5
-
-
MAX
500
420
200
145
8
250
85
UNIT
µA
µA
µA
µA
µA
mA
mA
Shutdown Supply Current
Driver Short-Circuit Current,
V
O
= High or Low
Receiver Short-Circuit Current
I
SHDN
I
OSD1
I
OSR
t
PLH
, t
PHL
t
SKEW
t
R
, t
F
t
ZH
t
ZL
t
HZ
t
LZ
t
PLH
, t
PHL
t
SKD
t
ZH
t
ZL
t
HZ
t
LZ
f
MAX
t
PLH
, t
PHL
t
SKEW
t
R
, t
F
t
ZH
t
ZL
t
HZ
t
LZ
t
PLH
, t
PHL
t
SKD
t
ZH
t
ZL
t
HZ
t
LZ
f
MAX
t
SHDN
t
ZH(SHDN)
t
ZL(SHDN)
(Note
12),
DE = 0V, RE = V
CC
, DI = 0V or V
CC
DE = V
CC
, -7V
V
Y
or V
Z
12V, (Note
9)
0V
V
O
V
CC
R
DIFF
= 54Ω, C
L
= 100pF, (Figure
2)
R
DIFF
= 54Ω, C
L
= 100pF, (Figure
2)
R
DIFF
= 54Ω, C
L
= 100pF, (Figure
2)
C
L
= 100pF, SW = GND, (Figure
2)
C
L
= 100pF, SW = V
CC
, (Figure
2)
C
L
= 15pF, SW = GND, (Figure
2)
C
L
= 15pF, SW = V
CC
, (Figure
2)
(Figure
4)
(Figure
4)
C
L
= 15pF, SW = GND, (Figure
5)
C
L
= 15pF, SW = V
CC
, (Figure
5)
C
L
= 15pF, SW = GND, (Figure
5)
C
L
= 15pF, SW = V
CC
, (Figure
5)
SWITCHING CHARACTERISTICS (ISL81487E)
Driver Input to Output Delay
Driver Output Skew
Driver Differential Rise or Fall Time
Driver Enable to Output High
Driver Enable to Output Low
Driver Disable from Output High
Driver Disable from Output Low
Receiver Input to Output Delay
Receiver Skew | t
PLH
- t
PHL
|
Receiver Enable to Output High
Receiver Enable to Output Low
Receiver Disable from Output High
Receiver Disable from Output Low
Maximum Data Rate
Full
Full
Full
Full
Full
Full
Full
Full
25
Full
Full
Full
Full
Full
15
-
3
-
-
-
-
30
-
-
-
-
-
5
24
3
12
14
14
44
21
90
5
9
9
9
9
-
50
10
25
70
70
70
70
150
-
50
50
50
50
-
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Mbps
SWITCHING CHARACTERISTICS (ISL8487E)
Driver Input to Output Delay
Driver Output Skew
Driver Differential Rise or Fall Time
Driver Enable to Output High
Driver Enable to Output Low
Driver Disable from Output High
Driver Disable from Output Low
Receiver Input to Output Delay
Receiver Skew | t
PLH
- t
PHL
|
Receiver Enable to Output High
Receiver Enable to Output Low
Receiver Disable from Output High
Receiver Disable from Output Low
Maximum Data Rate
Time to Shutdown
Driver Enable from Shutdown to
Output High
Driver Enable from Shutdown to
Output Low
R
DIFF
= 54Ω, C
L
= 100pF, (Figure
2)
R
DIFF
= 54Ω, C
L
= 100pF, (Figure
2)
R
DIFF
= 54Ω, C
L
= 100pF, (Figure
2)
C
L
= 100pF, SW = GND, (Figure
3, Note 10)
C
L
= 100pF, SW = V
CC
, (Figure
3, Note 10)
C
L
= 15pF, SW = GND, (Figure
3)
C
L
= 15pF, SW = V
CC
, (Figure
3)
(Figure
4)
(Figure
4)
C
L
= 15pF, SW = GND, (Figure
5, Note 11)
C
L
= 15pF, SW = V
CC
, (Figure
5, Note 11)
C
L
= 15pF, SW = GND, (Figure
5)
C
L
= 15pF, SW = V
CC
, (Figure
5)
(Note
12)
C
L
= 100pF, SW = GND, (Figure
3, Notes 12
and
13)
C
L
= 100pF, SW = V
CC
, (Figure
3, Notes 12
and
13)
Full
Full
Full
Full
Full
Full
Full
Full
25
Full
Full
Full
Full
Full
Full
Full
Full
250
-
250
250
250
300
300
250
-
-
-
-
-
250
50
-
-
650
160
900
1000
860
660
640
500
60
10
10
10
10
-
120
1000
1000
2000
800
2000
2000
2000
3000
3000
2000
-
50
50
50
50
-
600
2000
2000
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
kbps
ns
ns
ns
FN6051 Rev.8.00
Sep 20, 2018
Page 5 of 16
京公网安备 11010802033920号
EEWORLD
